ISO 13680:2020
Petroleum and natural gas industries — Corrosion-resistant alloy seamless tubular products for use as casing, tubing, coupling stock and accessory material — Technical delivery conditions
This document specifies the technical delivery conditions for corrosion-resistant alloy seamless tubular products for casing, tubing, coupling stock and accessory material (including coupling stock and accessory material from bar) for two product specification levels:
— PSL-1, which is the basis of this document;
— PSL-2, which provides additional requirements for a product that is intended to be both corrosion and cracking resistant for the environments and qualification method specified in Annex G and in the ISO 15156 series.
At the option of the manufacturer, PSL-2 products can be provided in lieu of PSL-1.
NOTE 1 The corrosion-resistant alloys included in this document are special alloys in accordance with ISO 4948-1 and ISO 4948-2.
NOTE 2 For the purpose of this document, NACE MR0175 is equivalent to the ISO 15156 series.
NOTE 3 Accessory products can be manufactured from coupling stock and tubular material, or from solid bar stock or from bored and heat heat-treated bar stock as covered in Annex F.
This document contains no provisions relating to the connection of individual lengths of pipe.
This document contains provisions relating to marking of tubing and casing after threading.
This document is applicable to the following five groups of products:
a) group 1, which is composed of stainless alloys with a martensitic or martensitic/ferritic structure;
b) group 2, which is composed of stainless alloys with a ferritic-austenitic structure, such as duplex and super-duplex stainless alloy;
c) group 3, which is composed of stainless alloys with an austenitic structure (iron base);
d) group 4, which is composed of nickel-based alloys with an austenitic structure (nickel base);
e) group 5, which is composed of bar only (Annex F) in age-hardened (AH) nickel-based alloys with austenitic structure.
NOTE 4 Not all PSL-1 categories and grades can be made cracking resistant in accordance with the ISO 15156 series and are, therefore, not included in PSL-2.
| Get this standard | Prices exclude GST | |
|---|---|---|
| PDF ( Single user document) |
$118.26 NZD
|
|
| HardCopy |
$152.17 NZD
|
|
| Networkable PDF |
Price varies
|
Foreword
Introduction
1 Scope
2 Normative references
3 Terms, definitions, abbreviated terms and symbols
3.1 Terms and definitions
3.2 Abbreviated terms
3.3 Symbols
4 General
4.1 Dual normative references
4.2 Units of measurement
5 Information supplied by the purchaser
6 Manufacturing process
6.1 Melting practices
6.2 Product manufacturing process
6.3 Pipe end sizing
6.4 Straightening
6.5 Process requiring validation
6.6 Traceability
6.7 Manufacturing procedure qualification test
6.8 Process for update of alloys and/or grades
7 Material requirements
7.1 Chemical composition
7.2 Tensile properties
7.3 Hardness properties
7.4 Charpy V-notch test properties — General requirements
7.4.1 Evaluation of test results
7.4.2 Critical thickness
7.4.3 Specimen size, orientation and hierarchy
7.4.4 Alternative size impact test specimens
7.4.5 Sub-size test specimens
7.4.6 Test temperature
7.5 Charpy V-notch — Absorbed energy requirements for coupling stock and accessory material — All grades
7.5.1 General
7.5.2 Requirements for all grades
7.6 Charpy V-notch — Absorbed energy requirements for pipe — All grades
7.7 Flattening requirements
7.8 Charpy V-notch test properties at low temperature for group 2
7.8.1 General
7.8.2 Evaluation of test results
7.8.3 Selection of test specimens
7.8.4 Test temperature
7.8.5 Absorbed energy requirements
7.9 Corrosion properties
7.9.1 General
7.9.2 Pitting corrosion properties for group 2
7.10 Microstructure properties
7.10.1 Group 1
7.10.2 Group 2
7.10.3 Groups 3 and 4
7.11 Surface condition
7.12 Defects
7.12.1 Pipe
7.12.2 Coupling stock and accessory material
7.12.3 Process control plan
8 Dimensions, masses and tolerances
8.1 Outside diameter, wall thickness and mass
8.2 Length
8.3 Tolerances
8.3.1 Tolerance on outside diameter, wall thickness and mass
8.3.2 Inside diameter, d
8.3.3 Straightness
8.3.4 Drift requirements
8.4 Product ends
9 Inspection and testing
9.1 Test equipment
9.2 Type and frequency of tests
9.3 Testing of chemical composition
9.3.1 Chemical analysis
9.3.2 Test method
9.3.3 Chromium depletion test — Groups 2, 3 and 4
9.4 Testing of mechanical characteristics
9.4.1 Test lot
9.4.2 Selection and preparation of samples and test pieces
9.5 Tensile test
9.5.1 Orientation and size of test pieces
9.5.2 Test method
9.5.3 Invalidation of test
9.5.4 Retest
9.6 Hardness test
9.6.1 Test pieces
9.6.2 Test method
9.6.3 Invalidation of tests
9.6.4 Periodic checks of hardness-testing machines
9.6.5 Verification of hardness-testing machines and indenters
9.6.6 Retests
9.7 Impact or flattening test
9.7.1 Test pieces
9.7.2 Frequency of testing
9.7.3 Impact test method
9.7.4 Flattening test method
9.7.5 Impact test retest
9.7.6 Flattening test retest
9.7.7 Invalidation of tests
9.8 Impact test at low temperature for group 2
9.9 Pitting corrosion test for group 2
9.10 Microstructural examination
9.10.1 Test pieces
9.10.2 Test method
9.10.3 Retest
9.11 Dimensional testing
9.11.1 General
9.11.2 Outside diameter
9.11.3 Wall thickness at end of products
9.11.4 Wall thickness of product body
9.12 Drift test
9.12.1 Non-upset and external upset pipe
9.12.2 Internal upset pipe
9.12.3 Drift mandrel coating
9.13 Length
9.14 Straightness
9.15 Mass determination
9.16 Visual inspection
9.16.1 General
9.16.2 Pipe body, coupling stock and accessory material
9.16.3 Pipe ends
9.16.4 Disposition
9.17 Non-destructive examination
9.17.1 General
9.17.2 NDE personnel
9.17.3 Products
9.17.4 Pup joints
9.17.5 Untested ends
9.17.6 Upset ends
9.17.7 Reference standards
9.17.8 NDE system capability records
9.17.9 All product group 1
9.17.10 Full-body NDE of product — Groups 2, 3 and 4
9.17.11 Pipe, coupling stock and accessory material requiring further evaluation
9.17.12 Evaluation of indications (prove-up)
9.17.13 Disposition of pipe containing defects
9.17.14 Disposition of coupling stock and accessory material containing defects
9.18 Positive material identification
10 Surface treatment
10.1 Group 1
10.2 Groups 2, 3 and 4
11 Marking
11.1 General
11.2 Colour-code identification
11.3 Marking content and sequence
11.4 Marking informative for couplings, pup joints and accessories after threading
12 Surface protection — Group 1
13 Documents
13.1 Electronic media
13.2 Retention of records
13.3 Test certificates
14 Handling, packaging and storage
14.1 General
14.2 Handling
14.3 Packaging
14.3.1 General
14.3.2 Identification
14.4 Storage
Annex A (normative) Tables in SI units
Annex B (normative) Figures in SI (USC) units
Annex C (normative) Tables in USC units
Annex D (normative) Purchaser inspection
Annex E (normative) Cleanliness requirements
Annex F (normative) Coupling blanks and accessory material from bar
Annex G (normative) Product specification level 2 (PSL-2)
Annex H (normative) Standardized manufacturing procedure qualification test
Annex I (informative) Photographic examples of microstructures, groups 2, 3 and 4
Bibliography
Previous versions
Keep me up-to-date
Sign up to receive updates when there are changes to this standard
Related Information
Similar Standards
-
AS/NZS 1518:2002
External extruded high-density-polyethylene coating system for pipes
-
AS/NZS 1518:2002 A1
External extruded high-density-polyethylene coating system for pipes: Amendment 1
-
AS/NZS 3862:2002
External fusion-bonded epoxy coating for steel pipes
-
BS 3604-2:1991
Steel pipes and tubes for pressure purposes: ferritic alloy steel with specified elevated temperature properties., Specification for longitudinally arc welded tubes
Foreword
Introduction
1 Scope
2 Normative references
3 Terms, definitions, abbreviated terms and symbols
3.1 Terms and definitions
3.2 Abbreviated terms
3.3 Symbols
4 General
4.1 Dual normative references
4.2 Units of measurement
5 Information supplied by the purchaser
6 Manufacturing process
6.1 Melting practices
6.2 Product manufacturing process
6.3 Pipe end sizing
6.4 Straightening
6.5 Process requiring validation
6.6 Traceability
6.7 Manufacturing procedure qualification test
6.8 Process for update of alloys and/or grades
7 Material requirements
7.1 Chemical composition
7.2 Tensile properties
7.3 Hardness properties
7.4 Charpy V-notch test properties — General requirements
7.4.1 Evaluation of test results
7.4.2 Critical thickness
7.4.3 Specimen size, orientation and hierarchy
7.4.4 Alternative size impact test specimens
7.4.5 Sub-size test specimens
7.4.6 Test temperature
7.5 Charpy V-notch — Absorbed energy requirements for coupling stock and accessory material — All grades
7.5.1 General
7.5.2 Requirements for all grades
7.6 Charpy V-notch — Absorbed energy requirements for pipe — All grades
7.7 Flattening requirements
7.8 Charpy V-notch test properties at low temperature for group 2
7.8.1 General
7.8.2 Evaluation of test results
7.8.3 Selection of test specimens
7.8.4 Test temperature
7.8.5 Absorbed energy requirements
7.9 Corrosion properties
7.9.1 General
7.9.2 Pitting corrosion properties for group 2
7.10 Microstructure properties
7.10.1 Group 1
7.10.2 Group 2
7.10.3 Groups 3 and 4
7.11 Surface condition
7.12 Defects
7.12.1 Pipe
7.12.2 Coupling stock and accessory material
7.12.3 Process control plan
8 Dimensions, masses and tolerances
8.1 Outside diameter, wall thickness and mass
8.2 Length
8.3 Tolerances
8.3.1 Tolerance on outside diameter, wall thickness and mass
8.3.2 Inside diameter, d
8.3.3 Straightness
8.3.4 Drift requirements
8.4 Product ends
9 Inspection and testing
9.1 Test equipment
9.2 Type and frequency of tests
9.3 Testing of chemical composition
9.3.1 Chemical analysis
9.3.2 Test method
9.3.3 Chromium depletion test — Groups 2, 3 and 4
9.4 Testing of mechanical characteristics
9.4.1 Test lot
9.4.2 Selection and preparation of samples and test pieces
9.5 Tensile test
9.5.1 Orientation and size of test pieces
9.5.2 Test method
9.5.3 Invalidation of test
9.5.4 Retest
9.6 Hardness test
9.6.1 Test pieces
9.6.2 Test method
9.6.3 Invalidation of tests
9.6.4 Periodic checks of hardness-testing machines
9.6.5 Verification of hardness-testing machines and indenters
9.6.6 Retests
9.7 Impact or flattening test
9.7.1 Test pieces
9.7.2 Frequency of testing
9.7.3 Impact test method
9.7.4 Flattening test method
9.7.5 Impact test retest
9.7.6 Flattening test retest
9.7.7 Invalidation of tests
9.8 Impact test at low temperature for group 2
9.9 Pitting corrosion test for group 2
9.10 Microstructural examination
9.10.1 Test pieces
9.10.2 Test method
9.10.3 Retest
9.11 Dimensional testing
9.11.1 General
9.11.2 Outside diameter
9.11.3 Wall thickness at end of products
9.11.4 Wall thickness of product body
9.12 Drift test
9.12.1 Non-upset and external upset pipe
9.12.2 Internal upset pipe
9.12.3 Drift mandrel coating
9.13 Length
9.14 Straightness
9.15 Mass determination
9.16 Visual inspection
9.16.1 General
9.16.2 Pipe body, coupling stock and accessory material
9.16.3 Pipe ends
9.16.4 Disposition
9.17 Non-destructive examination
9.17.1 General
9.17.2 NDE personnel
9.17.3 Products
9.17.4 Pup joints
9.17.5 Untested ends
9.17.6 Upset ends
9.17.7 Reference standards
9.17.8 NDE system capability records
9.17.9 All product group 1
9.17.10 Full-body NDE of product — Groups 2, 3 and 4
9.17.11 Pipe, coupling stock and accessory material requiring further evaluation
9.17.12 Evaluation of indications (prove-up)
9.17.13 Disposition of pipe containing defects
9.17.14 Disposition of coupling stock and accessory material containing defects
9.18 Positive material identification
10 Surface treatment
10.1 Group 1
10.2 Groups 2, 3 and 4
11 Marking
11.1 General
11.2 Colour-code identification
11.3 Marking content and sequence
11.4 Marking informative for couplings, pup joints and accessories after threading
12 Surface protection — Group 1
13 Documents
13.1 Electronic media
13.2 Retention of records
13.3 Test certificates
14 Handling, packaging and storage
14.1 General
14.2 Handling
14.3 Packaging
14.3.1 General
14.3.2 Identification
14.4 Storage
Annex A (normative) Tables in SI units
Annex B (normative) Figures in SI (USC) units
Annex C (normative) Tables in USC units
Annex D (normative) Purchaser inspection
Annex E (normative) Cleanliness requirements
Annex F (normative) Coupling blanks and accessory material from bar
Annex G (normative) Product specification level 2 (PSL-2)
Annex H (normative) Standardized manufacturing procedure qualification test
Annex I (informative) Photographic examples of microstructures, groups 2, 3 and 4
Bibliography