ISO 9021:2020
Motorcycles and mopeds — Controls — Types, positions and functions
This document describes the types, positions and functions of the rider-operated controls on a motorcycle/moped[1], in order to facilitate use.
Annex A specifies controls, indicators and tell-tales for which identification is obligatory and the appropriate graphical symbols. Annex B provides the information for applying for electrically propelled motorcycle/moped1).
This document applies to those controls which, when fitted, are commonly used by the rider of a motorcycle/moped.
The definition or specification of a control does not signify the mandatory presence of each and every control listed in this document on a vehicle.
[1] "motorcycle/moped" as defined in ISO 3833 but does not include a steering wheel type.
| Get this standard | Prices exclude GST | |
|---|---|---|
| PDF ( Single user document) |
$190.00 NZD
|
|
| Networkable PDF |
Price varies
|
Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 General requirements
4.1 Type and position
4.2 General design
4.3 Access
4.4 Identification
4.5 Orientation and directions
4.5.1 Right side/left side
4.5.2 Forward (in relation to the handlebars)
4.5.3 Clockwise/anticlockwise
5 Individual requirements
5.1 Electrical controls
5.1.1 Ignition switch/main switch
5.2 Engine controls
5.2.1 Starting
5.2.2 Speed
5.2.3 Stop
5.3 Brakes
5.3.1 Front (wheel) brake
5.3.2 Rear (wheel) brake
5.3.3 Combined service brake
5.3.4 Parking brake
5.4 Transmission
5.4.1 Clutch
5.4.2 Gear selection
5.5 Lighting and signalling controls
5.5.1 Horn (audible warning device)
5.5.2 Lighting
5.5.3 Direction-indicator switch
5.5.4 Hazard warning signal
5.6 Fuel supply controls
5.6.1 Cold starting device (manual choke)
5.6.2 Manual fuel shut-off control (manual fuel shut-off valve)
Annex A (normative) Controls, indicators and tell-tales for which (when fitted) identification is mandatory, and symbols to be used
Annex B (informative) Control for electrically propelled motorcycles and mopeds
Bibliography
Previous versions
Keep me up-to-date
Sign up to receive updates when there are changes to this standard
Related Information
Similar Standards
-
BS AU 193a:1990
Specification for replacement motor cycle and moped exhaust systems
-
BS AU 50-1.6.3a:1995
Tyres and wheels. Tyres. Motorcycle tyres, Specifications for designations, dimensions and load ratings for code designated series (diameter codes 4 to 12) tyres
-
BS AU 50-1.6.8:2000
Tyres and wheels. Tyres. Motorcycle tyres, Method of measuring tyre rolling circumference for new tyres under loaded conditions, Section 6: Motorcycle tyres Subsection 6.8: Method for measuring tyre rolling circumference for new tyres under loaded conditi
-
BS AU 50-1.7.1:1989
Tyres and wheels. Tyres. Moped tyres, Specification for tyre designations, dimensions and load ratings
Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 General requirements
4.1 Type and position
4.2 General design
4.3 Access
4.4 Identification
4.5 Orientation and directions
4.5.1 Right side/left side
4.5.2 Forward (in relation to the handlebars)
4.5.3 Clockwise/anticlockwise
5 Individual requirements
5.1 Electrical controls
5.1.1 Ignition switch/main switch
5.2 Engine controls
5.2.1 Starting
5.2.2 Speed
5.2.3 Stop
5.3 Brakes
5.3.1 Front (wheel) brake
5.3.2 Rear (wheel) brake
5.3.3 Combined service brake
5.3.4 Parking brake
5.4 Transmission
5.4.1 Clutch
5.4.2 Gear selection
5.5 Lighting and signalling controls
5.5.1 Horn (audible warning device)
5.5.2 Lighting
5.5.3 Direction-indicator switch
5.5.4 Hazard warning signal
5.6 Fuel supply controls
5.6.1 Cold starting device (manual choke)
5.6.2 Manual fuel shut-off control (manual fuel shut-off valve)
Annex A (normative) Controls, indicators and tell-tales for which (when fitted) identification is mandatory, and symbols to be used
Annex B (informative) Control for electrically propelled motorcycles and mopeds
Bibliography