ISO 11358-1:2014
Plastics — Thermogravimetry (TG) of polymers — Part 1: General principles
ISO 11358-1:2014 specifies general conditions for the analysis of polymers using thermogravimetric techniques. It is applicable to liquids or solids. Solid materials may be in the form of pellets, granules or powders. Fabricated shapes reduced to appropriate specimen size may also be analysed by this method.
| Get this standard | Prices exclude GST | |
|---|---|---|
| PDF ( Single user document) |
$126.00 NZD
|
|
| Networkable PDF |
Price varies
|
Section sec_1
Section sec_2
Section sec_3
Section sec_3.1
Section sec_3.2
Section sec_3.3
Section sec_4
Section sec_5
Section sec_5.1
Section sec_5.2
Section sec_6
Section sec_6.1
Section sec_6.2
Section sec_6.3
Section sec_6.4
Section sec_7
Section sec_7.1
Section sec_7.2
Section sec_8
Section sec_8.1
Section sec_8.2
Section sec_8.3
Section sec_9
Section sec_9.1
Section sec_9.2
Table tab_a
Figure fig_1
Section sec_9.3
Section sec_9.3.1
Table tab_c
Figure fig_2
Section sec_9.3.2
Table tab_e
Figure fig_3
Table tab_f
Figure fig_4
Section sec_9.3.3
Section sec_10
Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Principle
5 Apparatus
6 Test specimen preparation
6.1 General
6.2 Test specimens from finished products
6.3 Test specimen conditioning
6.4 Test specimen mass
7 Calibration
7.1 Mass calibration
7.2 Temperature calibration
8 Procedure
8.1 General
8.2 Temperature scanning mode
8.3 Isothermal mode
9 Expression of results
9.1 Graphical representation
9.2 Determination of increase in mass
9.3 Determination of loss in mass
10 Test report
Keep me up-to-date
Sign up to receive updates when there are changes to this standard
Related Information
Similar Standards
-
BS 2782-0:2011
Methods of testing plastic, Introduction
-
BS 2782-1:Method 140A:1992
Methods of testing plastics. Thermal properties, Determination of the burning behaviour of horizontal and vertical specimens in contact with a small-flame ignition source
-
BS 2782-1:Method 140E:1982
Methods of testing plastics. Thermal properties, Flammability of a small, inclined test piece exposed to an alcohol flame (laboratory method)
-
BS 2782-1:Method 150D:1976
Methods of testing plastics. Thermal properties, Cold crack temperature of film and thin sheeting
Section sec_1
Section sec_2
Section sec_3
Section sec_3.1
Section sec_3.2
Section sec_3.3
Section sec_4
Section sec_5
Section sec_5.1
Section sec_5.2
Section sec_6
Section sec_6.1
Section sec_6.2
Section sec_6.3
Section sec_6.4
Section sec_7
Section sec_7.1
Section sec_7.2
Section sec_8
Section sec_8.1
Section sec_8.2
Section sec_8.3
Section sec_9
Section sec_9.1
Section sec_9.2
Table tab_a
Figure fig_1
Section sec_9.3
Section sec_9.3.1
Table tab_c
Figure fig_2
Section sec_9.3.2
Table tab_e
Figure fig_3
Table tab_f
Figure fig_4
Section sec_9.3.3
Section sec_10
Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Principle
5 Apparatus
6 Test specimen preparation
6.1 General
6.2 Test specimens from finished products
6.3 Test specimen conditioning
6.4 Test specimen mass
7 Calibration
7.1 Mass calibration
7.2 Temperature calibration
8 Procedure
8.1 General
8.2 Temperature scanning mode
8.3 Isothermal mode
9 Expression of results
9.1 Graphical representation
9.2 Determination of increase in mass
9.3 Determination of loss in mass
10 Test report