AS/NZS 4365:2011
Radiocommunications equipment used in the UHF citizen band radio service
Specifies minimum essential performance requirements for radiocommunications equipment designed or intended to operate in the citizen band radio service, excluding repeater stations, in Australia and in New Zealand, in the UHF band. This edition incorporates revisions providing test methods and performance limits to facilitate 12.5 kHz channel operation in alignment with the Australian Communications and Media Authority (ACMA) 400 MHz band restructure and associated changes being made by the Ministry of Economic Development (MED) in New Zealand.
| Get this standard | Prices exclude GST | |
|---|---|---|
| PDF ( Single user document) |
$117.00 NZD
|
|
| HardCopy |
$130.00 NZD
|
|
| Networkable PDF |
Price varies
|
|
| Online Library ( Annual subscription) |
Info
Price varies
Online Library subscription information Online library subscriptions provide a cost-effective solution for organisations of any size to access the latest standards, offering 24/7 access to a personalised catalogue. The service ensures subscribers have have the most up-to-date version of selected standards, incluing automatic updates for any amendments or versions. Pricing is dependent on the chosen standards and the number of concurrent users, with discounts applied from the standards PDF price. For customised subscriptions or further inquiries, contact the Online Library team. |
AS/NZS 4365:2011 RADIOCOMMUNICATIONS EQUIPMENT USED IN THE UHF CITIZEN BAND RADIO SERVICE
PREFACE
CONTENTS
1 SCOPE
2 REFERENCED DOCUMENT
3 DEFINITIONS
3.1 Adjacent channel power (transmitter)
3.2 Artificial load
3.3 Carrier power (transmitter)
3.4 Citizen band radio service (CBRS)
3.5 Conducted spurious radiation (receiver)
3.6 Emission
3.7 End user
3.8 External Power Amplifier
3.9 F3E
3.10 Frequency error (transmitter)
3.11 G3E
3.12 Maximum frequency deviation
3.13 Multi-role device
3.14 Out-of-band modulation response
3.15 Personal mobile station
3.16 Rated transmitter output power
3.17 Repeater station
3.18 Spurious emissions (transmitter)
3.19 Selective calling
3.20 Telecommand
3.21 Telemetry
3.22 Time-out timer (TOT)
4 TEST CONDITIONS
4.1 Standard test conditions
4.1.1 Temperature and humidity
4.1.2 Test power source
4.2 Extreme test conditions
4.2.1 Extreme temperatures
4.2.2 Extreme test power-source voltages
4.3 Standard test modulation
4.4 Nominal test frequency
5 GENERAL REQUIREMENTS
5.1 External power amplifiers
5.2 Equipment markings
5.3 Equipment user manual
5.4 Adjustment mechanisms
5.5 Channel designation
5.6 Time-out timer
5.7 Channel-busy indicator
5.8 Operational timing requirements
5.9 Testing of units having only an integral antenna
5.10 Selective call inhibiting
5.11 Call-tone facility
5.12 Transmitter release tone
6 TRANSMITTER REQUIREMENTS AND TEST METHODS
6.1 Emission
6.1.1 Modes
6.1.2 Use of channels 22 and 23
6.1.3 Automatic station identification and/or position information
6.1.4 Start up channel
6.2 Nominal carrier frequency
6.3 Frequency error
6.3.1 Limits
6.3.2 Method of test
6.4 Transmitter transient performance
6.4.1 Limits
6.4.2 Method of test
6.5 Carrier power
6.5.1 Limits
6.5.2 Method of test
6.6 Maximum frequency deviation
6.6.1 Limit
6.6.2 Method of test
6.7 Adjacent channel power
6.7.1 Limit for analogue speech transmissions
6.7.2 Method of test for analogue speech transmissions
6.7.3 Limit for telemetry or telecommand transmissions
6.7.4 Method of test for telemetry or telecommand transmissions
6.8 Conducted spurious emissions
6.8.1 Limit
6.8.2 Method of test
6.9 Out-of-band modulation response
6.9.1 Limits
6.9.2 Method of test
7 RECEIVER REQUIREMENTS AND TEST METHODS
7.1 Limit for conducted spurious radiation
7.2 Method of test
APPENDIX A - CHARACTERISTICS OF POWER MEASURING RECEIVER
A1 GENERAL
A2 POWER MEASURING RECEIVER SPECIFICATION
A3 IF FILTER
A4 ATTENUATION INDICATOR
A5 RMS VALUE INDICATOR
A6 OSCILLATOR AND AMPLIFIER
Previous versions
Keep me up-to-date
Sign up to receive updates when there are changes to this standard
Related Information
Radiocommunications Regulations (General User Radio Licence for Citizen Band Radio) Notice 2011
Ministry: Ministry of Business Innovation and Employment - Records & Library Services
Section: 6(10)
Citation context:The supply of CB transmitter equipment operating in the 476.4 MHz - 477.425 MHz band that does not comply with AS/NZS 4365:2011 shall cease on 1 December 2012
Radiocommunications (Radio Standards) Notice 2010 - Revoked
Ministry: Ministry of Business Innovation and Employment - Records & Library Services
Section: Table 1
Citation context:Listed as a Standard applicable to personal communications
Radiocommunications Regulations (Radio Standards) Notice 2020 - Revoked
Ministry: Ministry of Business Innovation and Employment - Records & Library Services
Section: Table 1
Citation context:Listed as a standard applicable to citizen band radio service (476 MHz), compliance meets A2 level of conformity.
Radiocommunications Regulations (Radio Standards) Notice 2015 - Revoked
Ministry: Ministry of Business Innovation and Employment - Records & Library Services
Section: Table 1
Citation context:Listed as a Standard applicable to personal communications
Radiocommunications Regulations (Radio Standards) Notice 2016 - Revoked
Ministry: Ministry of Business Innovation and Employment - Records & Library Services
Section: Table 1
Citation context:Listed as a Standard applicable to personal communications
Similar Standards
-
AS/NZS 4417.1:2012
Regulatory compliance mark for electrical and electronic equipment - Part 1: Use of the mark -
AS/NZS 4417.1:2012AA
Regulatory compliance mark for electrical and electronic equipment - Part 1: Use of the mark: Amendment A -
AS/NZS 61000.1.1:2000
Electromagnetic compatibility (EMC) - General - Application and interpretation of fundamental definitions and terms
-
AS/NZS 61000.2.12:2003
Electromagnetic compatibility (EMC) - Environment - Compatibility levels for low-frequency conducted disturbances and signalling in public medium-voltage power supply systems
AS/NZS 4365:2011 RADIOCOMMUNICATIONS EQUIPMENT USED IN THE UHF CITIZEN BAND RADIO SERVICE
PREFACE
CONTENTS
1 SCOPE
2 REFERENCED DOCUMENT
3 DEFINITIONS
3.1 Adjacent channel power (transmitter)
3.2 Artificial load
3.3 Carrier power (transmitter)
3.4 Citizen band radio service (CBRS)
3.5 Conducted spurious radiation (receiver)
3.6 Emission
3.7 End user
3.8 External Power Amplifier
3.9 F3E
3.10 Frequency error (transmitter)
3.11 G3E
3.12 Maximum frequency deviation
3.13 Multi-role device
3.14 Out-of-band modulation response
3.15 Personal mobile station
3.16 Rated transmitter output power
3.17 Repeater station
3.18 Spurious emissions (transmitter)
3.19 Selective calling
3.20 Telecommand
3.21 Telemetry
3.22 Time-out timer (TOT)
4 TEST CONDITIONS
4.1 Standard test conditions
4.1.1 Temperature and humidity
4.1.2 Test power source
4.2 Extreme test conditions
4.2.1 Extreme temperatures
4.2.2 Extreme test power-source voltages
4.3 Standard test modulation
4.4 Nominal test frequency
5 GENERAL REQUIREMENTS
5.1 External power amplifiers
5.2 Equipment markings
5.3 Equipment user manual
5.4 Adjustment mechanisms
5.5 Channel designation
5.6 Time-out timer
5.7 Channel-busy indicator
5.8 Operational timing requirements
5.9 Testing of units having only an integral antenna
5.10 Selective call inhibiting
5.11 Call-tone facility
5.12 Transmitter release tone
6 TRANSMITTER REQUIREMENTS AND TEST METHODS
6.1 Emission
6.1.1 Modes
6.1.2 Use of channels 22 and 23
6.1.3 Automatic station identification and/or position information
6.1.4 Start up channel
6.2 Nominal carrier frequency
6.3 Frequency error
6.3.1 Limits
6.3.2 Method of test
6.4 Transmitter transient performance
6.4.1 Limits
6.4.2 Method of test
6.5 Carrier power
6.5.1 Limits
6.5.2 Method of test
6.6 Maximum frequency deviation
6.6.1 Limit
6.6.2 Method of test
6.7 Adjacent channel power
6.7.1 Limit for analogue speech transmissions
6.7.2 Method of test for analogue speech transmissions
6.7.3 Limit for telemetry or telecommand transmissions
6.7.4 Method of test for telemetry or telecommand transmissions
6.8 Conducted spurious emissions
6.8.1 Limit
6.8.2 Method of test
6.9 Out-of-band modulation response
6.9.1 Limits
6.9.2 Method of test
7 RECEIVER REQUIREMENTS AND TEST METHODS
7.1 Limit for conducted spurious radiation
7.2 Method of test
APPENDIX A - CHARACTERISTICS OF POWER MEASURING RECEIVER
A1 GENERAL
A2 POWER MEASURING RECEIVER SPECIFICATION
A3 IF FILTER
A4 ATTENUATION INDICATOR
A5 RMS VALUE INDICATOR
A6 OSCILLATOR AND AMPLIFIER
Previous versions
AS/NZS 4365:2011
Online Library subscription information
Online library subscriptions provide a cost-effective solution for organisations of any size to access the latest standards, offering 24/7 access to a personalised catalogue. The service ensures subscribers have have the most up-to-date version of selected standards, incluing automatic updates for any amendments or versions. Pricing is dependent on the chosen standards and the number of concurrent users, with discounts applied from the standards PDF price. For customised subscriptions or further inquiries, contact the Online Library team.