ISO 7778:2014
Through-thickness characteristics for steel products
ISO 7778:2014 specifies the criteria for through-thickness reduction of area properties specified in the direction of thickness perpendicular to the surface. It also specifies the test conditions by which conformance to the specified criteria is evaluated.
ISO 7778:2014 applies to fully killed steel with a specified minimum yield strength or proof strength ≤960 MPa and supplied as plates, wide flats, or sections of thickness from 15 mm to 400 mm.
| Get this standard | Prices exclude GST | |
|---|---|---|
| PDF ( Single user document) |
$141.75 NZD
|
|
| Networkable PDF |
Price varies
|
Section sec_1
Section sec_2
Section sec_3
Table tab_1
Section sec_4
Section sec_5
Section sec_5.1
Table tab_2
Section sec_5.2
Section sec_5.3
Section sec_5.3.1
Section sec_5.3.2
Section sec_6
Section sec_6.1
Section sec_6.1.1
Table tab_3
Section sec_6.1.2
Section sec_6.1.3
Section sec_6.1.4
Section sec_6.2
Section sec_6.2.1
Section sec_6.2.2
Section sec_6.2.2.1
Section sec_6.2.2.2
Section sec_6.2.2.3
Section sec_6.2.3
Section sec_6.2.4
Section sec_6.2.5
Table tab_b
Figure fig_1
Table tab_c
Figure fig_2
Reference ref_1
Reference ref_2
Reference ref_3
Reference ref_4
Reference ref_5
Reference ref_6
Foreword
Introduction
1 Scope
2 Normative references
3 Requirements
4 Designation
5 Number and selection of test pieces
5.1 Test unit for flat products
5.2 Test unit for sections
5.3 Sampling
6 Test methods
6.1 Test pieces
6.2 Tensile test
Bibliography
Previous versions
Keep me up-to-date
Sign up to receive updates when there are changes to this standard
Related Information
Similar Standards
-
AS/NZS 1365:1996
Tolerances for flat-rolled steel products
-
AS/NZS 1365:1996A1
Tolerances for flat-rolled steel products: Amendment 1 -
AS/NZS 1594:2025
Hot-rolled steel flat products
-
AS/NZS 1595:1998
Cold-rolled, unalloyed, steel sheet and strip
Section sec_1
Section sec_2
Section sec_3
Table tab_1
Section sec_4
Section sec_5
Section sec_5.1
Table tab_2
Section sec_5.2
Section sec_5.3
Section sec_5.3.1
Section sec_5.3.2
Section sec_6
Section sec_6.1
Section sec_6.1.1
Table tab_3
Section sec_6.1.2
Section sec_6.1.3
Section sec_6.1.4
Section sec_6.2
Section sec_6.2.1
Section sec_6.2.2
Section sec_6.2.2.1
Section sec_6.2.2.2
Section sec_6.2.2.3
Section sec_6.2.3
Section sec_6.2.4
Section sec_6.2.5
Table tab_b
Figure fig_1
Table tab_c
Figure fig_2
Reference ref_1
Reference ref_2
Reference ref_3
Reference ref_4
Reference ref_5
Reference ref_6
Foreword
Introduction
1 Scope
2 Normative references
3 Requirements
4 Designation
5 Number and selection of test pieces
5.1 Test unit for flat products
5.2 Test unit for sections
5.3 Sampling
6 Test methods
6.1 Test pieces
6.2 Tensile test
Bibliography