ISO 6195:2013
Fluid power systems and components — Cylinder-rod wiper-ring housings in reciprocating applications — Dimensions and tolerances
ISO 6195:2013 specifies dimensions and tolerances of housings for wiper rings used in reciprocating rod applications for fluid power cylinders. The range of rod diameters is from 4 mm to 360 mm.
ISO 6195:2013 is applicable to the following five housing designs.
- Type A: recessed housings with undercut or separate cover to retain elastomeric wipers.
- Type B: open recessed housings for wipers with integral rigid enforcement, that are press-fit in the housing.
- Type C: recessed housings with undercut to retain elastomeric wipers (these are the preferred housings for double lip wipers without integral rigid enforcement).
- Type D: recessed housings with undercut to retain elastomer-energized, plastic-faced wipers.
- Type E: recessed housings with undercut or separate cover to retain elastomeric wipers (these are the preferred housings for single lip wipers without integral rigid enforcement).
| Get this standard | Prices exclude GST | |
|---|---|---|
| PDF ( Single user document) |
$118.26 NZD
|
|
| HardCopy |
$152.17 NZD
|
|
| Networkable PDF |
Price varies
|
Section sec_1
Figure fig_1
Section sec_2
Section sec_3
Section sec_4
Section sec_5
Section sec_6
Section sec_6.1
Section sec_6.1.1
Section sec_6.1.2
Section sec_6.1.3
Table tab_b
Figure fig_2
Table tab_1
Section sec_6.2
Section sec_6.2.1
Section sec_6.2.2
Section sec_6.2.3
Table tab_c
Figure fig_3
Table tab_2
Section sec_6.3
Section sec_6.3.1
Section sec_6.3.2
Table tab_d
Figure fig_4
Table tab_3
Section sec_6.4
Section sec_6.4.1
Section sec_6.4.2
Table tab_e
Figure fig_5
Table tab_4
Section sec_6.5
Section sec_6.5.1
Section sec_6.5.2
Section sec_6.5.3
Table tab_f
Figure fig_6
Table tab_5
Section sec_7
Section sec_7.1
Section sec_7.2
Section sec_7.3
Section sec_7.4
Table tab_6
Section sec_8
Section sec_8.1
Section sec_8.2
Section sec_8.3
Table tab_7
Section sec_9
Reference ref_1
Reference ref_2
Reference ref_3
Reference ref_4
Reference ref_5
Reference ref_6
Reference ref_7
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Letter symbols
5 General
6 Requirements for housings
6.1 Type A housing
6.2 Type B housing
6.3 Type C housing
6.4 Type D housing
6.5 Type E housing
7 Other requirements regarding dimensions
8 Surface roughness
9 Identification statement (reference to this International Standard)
Bibliography
Previous versions
Keep me up-to-date
Sign up to receive updates when there are changes to this standard
Related Information
Similar Standards
-
BS EN 13001-3-6:2018+A1:2021
Cranes. General design, Limit states and proof of competence of machinery. Hydraulic cylinders
-
BS ISO 10099:2001
Pneumatic fluid power. Cylinders. Final examination and acceptance criteria
-
BS ISO 10100:2020
Hydraulic fluid power. Cylinders. Acceptance tests
-
BS ISO 10762:2015
Hydraulic fluid power. Mounting dimensions for cylinders, 10 MPa (100 bar) series
Section sec_1
Figure fig_1
Section sec_2
Section sec_3
Section sec_4
Section sec_5
Section sec_6
Section sec_6.1
Section sec_6.1.1
Section sec_6.1.2
Section sec_6.1.3
Table tab_b
Figure fig_2
Table tab_1
Section sec_6.2
Section sec_6.2.1
Section sec_6.2.2
Section sec_6.2.3
Table tab_c
Figure fig_3
Table tab_2
Section sec_6.3
Section sec_6.3.1
Section sec_6.3.2
Table tab_d
Figure fig_4
Table tab_3
Section sec_6.4
Section sec_6.4.1
Section sec_6.4.2
Table tab_e
Figure fig_5
Table tab_4
Section sec_6.5
Section sec_6.5.1
Section sec_6.5.2
Section sec_6.5.3
Table tab_f
Figure fig_6
Table tab_5
Section sec_7
Section sec_7.1
Section sec_7.2
Section sec_7.3
Section sec_7.4
Table tab_6
Section sec_8
Section sec_8.1
Section sec_8.2
Section sec_8.3
Table tab_7
Section sec_9
Reference ref_1
Reference ref_2
Reference ref_3
Reference ref_4
Reference ref_5
Reference ref_6
Reference ref_7
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Letter symbols
5 General
6 Requirements for housings
6.1 Type A housing
6.2 Type B housing
6.3 Type C housing
6.4 Type D housing
6.5 Type E housing
7 Other requirements regarding dimensions
8 Surface roughness
9 Identification statement (reference to this International Standard)
Bibliography