ISO 6162-1:2002
Hydraulic fluid power — Flange connectors with split or one-piece flange clamps and metric or inch screws — Part 1: Flange connectors for use at pressures of 3,5 MPa (35 bar) to 35 MPa (350 bar), DN 13 to DN 127
ISO 6162-1:2002 specifies complete general and dimensional characteristics for flange heads, split flange clamps (FCS), one-piece flange clamps (FC) and ports applicable to four-screw, split and one-piece flange clamp type tube and hose connectors for use at pressures of 3,5 MPa (35 bar) to 35 MPa (350 bar). It also specifies the dimensions of the seals to be used, as well as the grooves to house the seal.
ISO 6162-1:2002 also recognizes the need to accommodate metric screw fasteners, as well as to provide a means to use existing inch screw fasteners.
| Get this standard | Prices exclude GST | |
|---|---|---|
| PDF ( Single user document) |
$141.75 NZD
|
|
| HardCopy |
$194.63 NZD
|
|
| Networkable PDF |
Price varies
|
TitlePage - Hydraulic fluid power— Flange connectors with split or one-piece flange clamps and m...
TableofContent - Contents Page
Foreword - Foreword
Introduction - Introduction
Scope - 1 Scope
NormativeReference - 2 Normative references
Clause1 - 4 Material
UntitledSubclause2 - 4.1 Split flange clamp halves (see
UntitledSubclause2 - 4.2 Use flange heads made from ferrous material with:
UntitledSubclause2 - 4.3 Use hex head metric screws of property class8.8 or 10.9, as specifie...
UntitledSubclause2 - 4.4 Unless otherwise specified, the O-rings shall be made of NBR (nitrile...
Clause1 - 5 General specifications
UntitledSubclause2 - 5.1 Select from
UntitledSubclause2 - 5.2 Use hexagon head screws, unless otherwise specified.
UntitledSubclause2 - 5.3 If socket head cap screws are necessary and screws of property classe...
Clause1 - 6 Dimensions
Clause1 - 7 Tolerances
Clause1 - 8 Finish
UntitledSubclause2 - 8.1 The external surface on all flanges, except weld-on flange heads, sha...
UntitledSubclause2 - 8.2 Flange clamps shall meet the requirements of a
UntitledSubclause2 - 8.3 Screws and washers shall meet the requirements of a
UntitledSubclause2 - 8.4 Any appearance of red rust during the above salt spray tests shall be...
UntitledSubclause2 - 8.5 All connection components shall be free from hanging burrs, loose sca...
UntitledSubclause2 - 8.6 A smooth sealing surface shall be provided. Annular tool marks up to ...
UntitledSubclause2 - 8.7 For more specific finish requirements, see
Clause1 - 9 Pressure/temperature requirements
UntitledSubclause2 - 9.1 Testing shall be conducted in accordance with
UntitledSubclause2 - 9.2 Flange connectors complying with
UntitledSubclause2 - 9.3 Flange connectors complying with
Clause1 - 10 Marking
UntitledSubclause2 - 10.1 The flange head shall be permanently marked, at the minimum, with th...
UntitledSubclause2 - 10.2 Type1 clamp halves and one-piece flange clamps shall be permanently...
UntitledSubclause2 - 10.3 Type1 ports shall be permanently marked with an “M” for identificat...
Clause1 - 11 Designation of flange connections and their parts
Clause1 - 12 Identification statement
AnnexInformative - Equivalent SAE O-rings
AnnexInformative - Equivalent inch screw strengths
Bibliography - Bibliography
Keep me up-to-date
Sign up to receive updates when there are changes to this standard
Related Information
Similar Standards
-
AS/NZS 2280:2020
Ductile iron pipes and fittings -
AS/NZS 2280:2020 A1
Ductile iron pipes & fittings
-
BS 5200:1997
Specification for dimensions of hydraulic connectors and adaptors
-
BS 5242-2:1983
Tubes for fluid power cylinder barrels, Specification for non-ferrous metallic tubes with specially finished bores
TitlePage - Hydraulic fluid power— Flange connectors with split or one-piece flange clamps and m...
TableofContent - Contents Page
Foreword - Foreword
Introduction - Introduction
Scope - 1 Scope
NormativeReference - 2 Normative references
Clause1 - 4 Material
UntitledSubclause2 - 4.1 Split flange clamp halves (see
UntitledSubclause2 - 4.2 Use flange heads made from ferrous material with:
UntitledSubclause2 - 4.3 Use hex head metric screws of property class8.8 or 10.9, as specifie...
UntitledSubclause2 - 4.4 Unless otherwise specified, the O-rings shall be made of NBR (nitrile...
Clause1 - 5 General specifications
UntitledSubclause2 - 5.1 Select from
UntitledSubclause2 - 5.2 Use hexagon head screws, unless otherwise specified.
UntitledSubclause2 - 5.3 If socket head cap screws are necessary and screws of property classe...
Clause1 - 6 Dimensions
Clause1 - 7 Tolerances
Clause1 - 8 Finish
UntitledSubclause2 - 8.1 The external surface on all flanges, except weld-on flange heads, sha...
UntitledSubclause2 - 8.2 Flange clamps shall meet the requirements of a
UntitledSubclause2 - 8.3 Screws and washers shall meet the requirements of a
UntitledSubclause2 - 8.4 Any appearance of red rust during the above salt spray tests shall be...
UntitledSubclause2 - 8.5 All connection components shall be free from hanging burrs, loose sca...
UntitledSubclause2 - 8.6 A smooth sealing surface shall be provided. Annular tool marks up to ...
UntitledSubclause2 - 8.7 For more specific finish requirements, see
Clause1 - 9 Pressure/temperature requirements
UntitledSubclause2 - 9.1 Testing shall be conducted in accordance with
UntitledSubclause2 - 9.2 Flange connectors complying with
UntitledSubclause2 - 9.3 Flange connectors complying with
Clause1 - 10 Marking
UntitledSubclause2 - 10.1 The flange head shall be permanently marked, at the minimum, with th...
UntitledSubclause2 - 10.2 Type1 clamp halves and one-piece flange clamps shall be permanently...
UntitledSubclause2 - 10.3 Type1 ports shall be permanently marked with an “M” for identificat...
Clause1 - 11 Designation of flange connections and their parts
Clause1 - 12 Identification statement
AnnexInformative - Equivalent SAE O-rings
AnnexInformative - Equivalent inch screw strengths
Bibliography - Bibliography