ISO 21307:2017
Plastics pipes and fittings — Butt fusion jointing procedures for polyethylene (PE) piping systems
ISO 21307:2017 establishes general principles regarding the procedure used in the construction and quality assessment of butt fusion jointing of polyethylene (PE) piping system components specified in accordance with relevant ISO standards. These components are installed in accordance with the relevant codes of practice, national regulations or industry guidance. Specifically, this document specifies three butt fusion jointing procedures for PE pipes and fittings. These are:
- single low-pressure fusion jointing procedure;
- dual low-pressure fusion jointing procedure;
- single high-pressure fusion jointing procedure.
ISO 21307:2017 takes into consideration the materials and components used, the fusion jointing procedure and equipment and the quality assessment of the completed joint. It can be applied in conjunction with appropriate national regulations and standards.
| Get this standard | Prices exclude GST | |
|---|---|---|
| PDF ( Single user document) |
$213.75 NZD
|
|
| HardCopy |
$267.75 NZD
|
|
| Networkable PDF |
Price varies
|
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Butt fusion jointing process
4.1 General
4.2 Principle
4.3 Cleaning the pipe or fitting ends, planing unit and heater surfaces
4.4 Clamping the components
4.5 Planing the pipe or fitting ends
4.6 Aligning the pipes or fittings
4.7 Calculation of the gauge pressure
4.8 Determination of the drag pressure
4.9 Heating the pipe or fitting ends
4.10 Jointing the pipe or fitting ends
4.11 Cooling the pipe or fitting ends
5 Butt fusion jointing procedures
5.1 General
5.2 Single low-pressure fusion jointing procedure
5.3 Dual low-pressure fusion jointing procedure
5.4 Single high-pressure fusion jointing procedure
6 Quality control
6.1 General
6.2 Destructive joint integrity testing
6.3 Non-destructive joint integrity testing
Annex A (informative) Examples of values of parameters for single low-pressure fusion jointing procedure
Annex B (informative) Examples of values of parameters for dual low-pressure fusion jointing procedure
Annex C (informative) Examples of values of parameters for single high-pressure fusion jointing procedure
Bibliography
Previous versions
Keep me up-to-date
Sign up to receive updates when there are changes to this standard
Related Information
Similar Standards
-
AS/NZS 1254:2010
PVC-U pipes and fittings for stormwater and surface water applications
-
AS/NZS 1254:2010 A1
PVC-U pipes and fittings for stormwater and surface water applications: Amendment 1 -
AS/NZS 1254:2010 A2
PVC-U pipes and fittings for stormwater and surface water applications: Amendment 2 -
AS/NZS 1254:2010 A3
PVC-U pipes and fittings for stormwater and surface water applications: Amendment 3
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Butt fusion jointing process
4.1 General
4.2 Principle
4.3 Cleaning the pipe or fitting ends, planing unit and heater surfaces
4.4 Clamping the components
4.5 Planing the pipe or fitting ends
4.6 Aligning the pipes or fittings
4.7 Calculation of the gauge pressure
4.8 Determination of the drag pressure
4.9 Heating the pipe or fitting ends
4.10 Jointing the pipe or fitting ends
4.11 Cooling the pipe or fitting ends
5 Butt fusion jointing procedures
5.1 General
5.2 Single low-pressure fusion jointing procedure
5.3 Dual low-pressure fusion jointing procedure
5.4 Single high-pressure fusion jointing procedure
6 Quality control
6.1 General
6.2 Destructive joint integrity testing
6.3 Non-destructive joint integrity testing
Annex A (informative) Examples of values of parameters for single low-pressure fusion jointing procedure
Annex B (informative) Examples of values of parameters for dual low-pressure fusion jointing procedure
Annex C (informative) Examples of values of parameters for single high-pressure fusion jointing procedure
Bibliography