ISO 21100:2014
Air cargo unit load devices — Performance requirements and test parameters
The purpose ISO 21100:2014 is to establish the minimum requirements for airworthiness approval of air cargo pallets, nets and containers, generally designated as air cargo unit load devices.
ISO 21100:2014 defines the minimum performance requirements and test parameters for air cargo unit load devices requiring approval of airworthiness for installation in an approved aircraft cargo compartment and restraint system that complies with the cargo restraint and occupant protection requirements of EASA CS-25 or 14 CFR Part 25, except for the 9,0 g forward ultimate inertia force.
ISO 21100:2014 applies to airworthiness approved air cargo unit load devices intended for carriage on board civil transport category airplanes type certificated under EASA CS-25 or 14 CFR Part 25.
ISO 21100:2014 exclusively applies to unit load devices airworthiness approval and testing parameters. It does not apply to either aircraft design or aircraft operating requirements, which are provided by the approved Weight and Balance Manual for each aircraft type.
| Get this standard | Prices exclude GST | |
|---|---|---|
| PDF ( Single user document) |
$141.75 NZD
|
|
| HardCopy |
$194.63 NZD
|
|
| Networkable PDF |
Price varies
|
Section sec_1
Section sec_1.1
Section sec_1.2
Section sec_1.3
Section sec_1.4
Section sec_1.5
Section sec_1.6
Section sec_1.7
Section sec_2
Section sec_2.1
Section sec_2.2
Section sec_2.3
Section sec_2.3.1
Section sec_2.3.2
Section sec_2.3.3
Section sec_2.3.4
Section sec_2.3.5
Section sec_2.3.6
Section sec_2.3.7
Section sec_3
Section sec_3.1
Section sec_3.2
Section sec_3.3
Section sec_3.3.1
Section sec_3.3.2
Section sec_3.3.3
Section sec_3.4
Section sec_3.5
Section sec_4
Section sec_4.1
Section sec_4.2
Section sec_4.3
Section sec_4.4
Section sec_4.5
Section sec_4.6
Section sec_4.7
Section sec_4.8
Section sec_4.9
Section sec_4.10
Section sec_4.10.1
Section sec_4.10.1.1
Section sec_4.10.1.2
Section sec_4.10.1.3
Section sec_4.10.1.4
Section sec_4.10.2
Section sec_4.10.3
Section sec_4.10.3.1
Section sec_4.10.3.2
Section sec_4.10.3.3
Section sec_4.10.3.4
Section sec_4.10.3.5
Section sec_4.10.4
Section sec_4.10.4.1
Section sec_4.10.4.2
Section sec_4.10.4.3
Section sec_4.11
Section sec_5
Section sec_5.1
Section sec_5.2
Section sec_5.3
Section sec_5.4
Section sec_6
Section sec_6.1
Section sec_6.2
Section sec_6.3
Section sec_6.4
Section sec_7
Section sec_7.1
Section sec_7.2
Table tab_1
Table tab_A.7
Table tab_c
Table tab_A.8
Table tab_d
Table tab_B.7
Table tab_e
Table tab_B.8
Table tab_f
Table tab_G.1
Table tab_g
Table tab_K.4
Table tab_h
Table tab_L.5
Table tab_i
Table tab_L.6
Table tab_j
Table tab_M.4
Table tab_k
Table tab_M.5
Table tab_l
Table tab_N.1
Table tab_m
Table tab_P.1
Table tab_Q.1
Table tab_R.1
Table tab_n
Table tab_S.1
Table tab_o
Section sec_8
Table tab_2
Table tab_p
Table tab_q
Table tab_r
Table tab_s
Table tab_t
Table tab_v
Table tab_w
Table tab_x
Table tab_y
Table tab_z
Table tab_aa
Table tab_ab
Table tab_ac
Table tab_ad
Table tab_ae
Table tab_af
Table tab_ag
Table tab_ah
Reference ref_1
Reference ref_2
Reference ref_3
Reference ref_4
Reference ref_5
Reference ref_6
Reference ref_7
Reference ref_8
Reference ref_9
Reference ref_10
Reference ref_11
Reference ref_12
Reference ref_13
Reference ref_14
Reference ref_15
Reference ref_16
Reference ref_17
Reference ref_18
Reference ref_19
Reference ref_20
Reference ref_21
Reference ref_22
Reference ref_23
Foreword
1 Scope
2 References and terms and definitions
2.1 Government regulations
2.2 Normative references
2.3 Terms and definitions
3 Classification
3.1 Types
3.2 Sizes
3.3 Configurations
3.4 Forms
3.5 Classification identifier
4 Performance requirements
4.1 Materials
4.2 Fabrication methods and workmanship
4.3 Protection
4.4 Construction
4.5 Marking
4.6 Inspection provisions
4.7 Fire protection
4.8 Rapid decompression
4.9 Dimensions and tolerances
4.10 Strength
4.11 Environmental degradation
5 Tests
5.1 Test requirements
5.2 Test parameters
5.3 Test methods
5.4 Test results
6 Additional
6.1 Intended use
6.2 Unit load device capacities
6.3 Container contours
6.4 Pallet configurations
7 Unit load device configurations
8 Testing restraint conditions
Bibliography
Keep me up-to-date
Sign up to receive updates when there are changes to this standard
Related Information
Similar Standards
-
BS 185-13:1972
Glossary of aeronautical and astronautical terms, Air-traffic and ground services
-
BS 2C 11:1988
Specification for ground pressure test connections for aircraft pressure cabins
-
BS 2C 13:1988
Specification for sizes of aircraft gravity filling orifices and associated replenishment nozzles (metric series)
-
BS 2C 19:1994
Specification for pressure re-oiling connection (new type)
Section sec_1
Section sec_1.1
Section sec_1.2
Section sec_1.3
Section sec_1.4
Section sec_1.5
Section sec_1.6
Section sec_1.7
Section sec_2
Section sec_2.1
Section sec_2.2
Section sec_2.3
Section sec_2.3.1
Section sec_2.3.2
Section sec_2.3.3
Section sec_2.3.4
Section sec_2.3.5
Section sec_2.3.6
Section sec_2.3.7
Section sec_3
Section sec_3.1
Section sec_3.2
Section sec_3.3
Section sec_3.3.1
Section sec_3.3.2
Section sec_3.3.3
Section sec_3.4
Section sec_3.5
Section sec_4
Section sec_4.1
Section sec_4.2
Section sec_4.3
Section sec_4.4
Section sec_4.5
Section sec_4.6
Section sec_4.7
Section sec_4.8
Section sec_4.9
Section sec_4.10
Section sec_4.10.1
Section sec_4.10.1.1
Section sec_4.10.1.2
Section sec_4.10.1.3
Section sec_4.10.1.4
Section sec_4.10.2
Section sec_4.10.3
Section sec_4.10.3.1
Section sec_4.10.3.2
Section sec_4.10.3.3
Section sec_4.10.3.4
Section sec_4.10.3.5
Section sec_4.10.4
Section sec_4.10.4.1
Section sec_4.10.4.2
Section sec_4.10.4.3
Section sec_4.11
Section sec_5
Section sec_5.1
Section sec_5.2
Section sec_5.3
Section sec_5.4
Section sec_6
Section sec_6.1
Section sec_6.2
Section sec_6.3
Section sec_6.4
Section sec_7
Section sec_7.1
Section sec_7.2
Table tab_1
Table tab_A.7
Table tab_c
Table tab_A.8
Table tab_d
Table tab_B.7
Table tab_e
Table tab_B.8
Table tab_f
Table tab_G.1
Table tab_g
Table tab_K.4
Table tab_h
Table tab_L.5
Table tab_i
Table tab_L.6
Table tab_j
Table tab_M.4
Table tab_k
Table tab_M.5
Table tab_l
Table tab_N.1
Table tab_m
Table tab_P.1
Table tab_Q.1
Table tab_R.1
Table tab_n
Table tab_S.1
Table tab_o
Section sec_8
Table tab_2
Table tab_p
Table tab_q
Table tab_r
Table tab_s
Table tab_t
Table tab_v
Table tab_w
Table tab_x
Table tab_y
Table tab_z
Table tab_aa
Table tab_ab
Table tab_ac
Table tab_ad
Table tab_ae
Table tab_af
Table tab_ag
Table tab_ah
Reference ref_1
Reference ref_2
Reference ref_3
Reference ref_4
Reference ref_5
Reference ref_6
Reference ref_7
Reference ref_8
Reference ref_9
Reference ref_10
Reference ref_11
Reference ref_12
Reference ref_13
Reference ref_14
Reference ref_15
Reference ref_16
Reference ref_17
Reference ref_18
Reference ref_19
Reference ref_20
Reference ref_21
Reference ref_22
Reference ref_23
Foreword
1 Scope
2 References and terms and definitions
2.1 Government regulations
2.2 Normative references
2.3 Terms and definitions
3 Classification
3.1 Types
3.2 Sizes
3.3 Configurations
3.4 Forms
3.5 Classification identifier
4 Performance requirements
4.1 Materials
4.2 Fabrication methods and workmanship
4.3 Protection
4.4 Construction
4.5 Marking
4.6 Inspection provisions
4.7 Fire protection
4.8 Rapid decompression
4.9 Dimensions and tolerances
4.10 Strength
4.11 Environmental degradation
5 Tests
5.1 Test requirements
5.2 Test parameters
5.3 Test methods
5.4 Test results
6 Additional
6.1 Intended use
6.2 Unit load device capacities
6.3 Container contours
6.4 Pallet configurations
7 Unit load device configurations
8 Testing restraint conditions
Bibliography