AS/NZS 3800:2005
Electrical equipment for explosive atmospheres - Repair and overhaul
Sets out requirements for repair and overhaul of electrical equipment used in hazardous areas, which are defined in AS/NZS 60079.10 for gases and AS/NZS 61241.10 for dusts. It covers equipment having a group designation of Group I for coal mining and Group II for all other industries where flammable gases and vapours may be present. It covers all types of explosion-protection techniques and specifies requirements for repair and overhaul service facilities.
| Get this standard | Prices exclude GST | |
|---|---|---|
| PDF ( Single user document) |
$217.80 NZD
|
|
| HardCopy |
$242.00 NZD
|
|
| Networkable PDF |
Price varies
|
|
| Online Library ( Annual subscription) |
Info
Price varies
Online Library subscription pricing The cost of your subscription will depend on which standards you want to access, and how many people in your organisation need to be able to access the Online Library subscription at the same time (concurrent users). During your subscription period, we are also able to make any necessary changes and ensure you are aware of any pricing changes that result. For a quote, contact our Online Library team by emailing onlinelibrary@standards.govt.nz. |
AS/NZS 3800:2005 ELECTRICAL EQUIPMENT FOR EXPLOSIVE ATMOSPHERES-REPAIR AND OVERHAUL
PREFACE
CONTENTS
FOREWORD
SECTION 1 SCOPE AND GENERAL
1.1 SCOPE
1.2 APPLICATION
1.3 REFERENCED DOCUMENTS
1.4 DEFINITIONS
1.4.1 Approved
1.4.2 Australian Qualification Framework (AQF)
1.4.3 Certification
1.4.4 Competent person
1.4.5 Encapsulation (Ex ‚m™)
1.4.6 Enclosure, dust-excluding ignition-proof (DIP enclosure)
1.4.7 Equipment
1.4.8 Explosion-protection
1.4.9 Explosive gas atmosphere
1.4.10 Ex Testing Laboratory (ExTL)
1.4.11 Flameproof enclosure (Ex ‚d™)
1.4.12 Flameproof joint
1.4.13 Gap (diametral clearance)
1.4.14 Hazardous area
1.4.15 Increased safety protection (Ex ‚e™)
1.4.16 Intrinsically safe electrical equipment (Ex ‚i™)
1.4.17 Length of flamepath (width of joint)
1.4.18 Maintenance
1.4.19 Maximum surface temperature
1.4.20 Modification
1.4.21 Non-sparking protection (Ex ‚n™)
1.4.22 Operating rod (spindle)
1.4.23 Overhaul
1.4.24 Overhaul and examination report
1.4.25 Pressure piling
1.4.26 Pressurization (Ex ‚p™)
1.4.27 Recognized service facility
1.4.28 Repair
1.4.29 Replacement
1.4.30 Sand-filled enclosure (Ex ‚q™)
1.4.31 Special protection (Ex ‚s™)
1.4.32 Temperature classification
1.4.33 Verification dossier
1.5 DOCUMENTATION/INFORMATION
1.5.1 General
1.5.2 Where certification documentation is not available but sufficient information is available to identify the type of...
1.5.3 Insufficient information
1.5.4 Traceability/marking
1.5.5 Variation from certification documents
1.5.6 Acceptance criteria
1.6 MIXED EXPLOSION-PROTECTION TECHNIQUES
1.7 GROUPING OF EXPLOSION-PROTECTED ELECTRICAL EQUIPMENT
1.7.1 Group designation
1.7.2 Group II subdivision
1.8 ROLE OF COMPETENT PERSONS
SECTION 2 FLAMEPROOF ENCLOSURES (Ex 'd')
2.1 GENERAL
2.1.1 Flameproof enclosures
2.1.2 Use of greases
2.1.3 Fixing bolts, studs and nuts
2.1.4 Attachments
2.1.5 Replacement
2.1.6 Machining
2.1.7 Joint surfaces
2.1.8 Mixed protection techniques
2.2 CERTIFICATION
2.2.1 General
2.2.2 Flameproof tests
2.3 CATEGORIES OF WORK
2.3.1 General
2.3.2 Overhaul-No repair
2.3.3 Overhaul-Repair
2.3.4 Modifications
2.4 OVER-PRESSURE TESTING
2.4.1 General
2.4.2 Water-cooled motors and enclosures
2.4.3 Enclosures with screwed covers
2.5 OVERHAUL AND REPAIR PROCEDURES
2.5.1 Overhaul of Ex ‚d™-Flameproof motors
2.5.2 Overhaul of Ex™d™-Flameproof enclosures
2.5.3 Overhaul of electrical equipment installed within Ex ‚d™ enclosures
SECTION 3 INTRINSIC SAFETY(Ex 'i')
3.1 GENERAL
3.2 EQUIPMENT
3.2.1 Enclosures
3.2.2 Ingress protection
3.2.3 Plugs and sockets
3.2.4 Terminations
3.2.5 Fuses
3.2.6 Printed circuit boards
3.2.7 Optocouplers
3.2.8 Piezo-electric devices
3.2.9 Multi-core cables
3.2.10 Fibre optic cable
3.2.11 Electrical parts
3.2.12 Batteries
3.2.13 Transformers
3.2.14 Encapsulated parts
3.2.15 Non-electrical parts
3.3 MODIFICATIONS
3.4 OVERHAUL AND REPAIR PROCEDURES
3.4.1 General procedures
3.4.2 Specific procedures
SECTION 4 INCREASED SAFETY (Ex 'e')
4.1 GENERAL
4.2 EQUIPMENT
4.2.1 Enclosures
4.2.2 Ingress protection
4.2.3 Plugs and sockets
4.2.4 Terminations
4.2.5 Internal connections
4.2.6 Electrical parts
4.2.7 Batteries
4.2.8 Transformers
4.2.9 Light transmitting parts
4.2.10 Lamps
4.2.11 Lampholders
4.2.12 Ballasts and capacitors
4.2.13 Encapsulated parts
4.2.14 Insulation
4.2.15 Winding connections
4.3 MODIFICATIONS
4.3.1 Modifications permitted by certification
4.3.2 Modifications not permitted within certification
4.4 CERTIFICATION
4.5 OVERHAUL AND REPAIR PROCEDURES
4.5.1 Motor windings
4.5.2 Overhaul of Ex ‚e™-Increased safety motors
4.5.3 Overhaul of Ex ‚e™-Increased safety enclosures
4.5.4 Overhaul of electrical equipment installed within Ex ‚e™ enclosures
SECTION 5 PRESSURIZED ENCLOSURES (Ex ‚p™)
5.1 GENERAL
5.2 PRESSURIZATION
5.3 ENCLOSURES
5.3.1 Materials
5.3.2 Joints in the enclosure
5.3.3 Gaskets and seals
5.3.4 Fasteners
5.3.5 Cable entries
5.4 TEMPERATURE RATING
5.4.1 Lighting fittings
5.4.2 Heat-generating equipment
5.5 OVERHAUL AND REPAIR PROCEDURES
SECTION 6 NON-SPARKING (Ex 'n')
6.1 GENERAL
6.2 EQUIPMENT
6.2.1 Enclosures
6.2.2 Ingress protection
6.2.3 Plugs and sockets
6.2.4 Terminations
6.2.5 Internal connections
6.2.6 Electrical parts
6.2.7 Batteries
6.2.8 Transformers
6.2.9 Light-transmitting parts
6.2.10 Lamps
6.2.11 Lampholders
6.2.12 Ballasts and capacitors
6.2.13 Encapsulated parts
6.2.14 Insulation
6.2.15 Winding connections
6.3 MODIFICATIONS
6.3.1 Modifications permitted by certification
6.3.2 Modifications not permitted within certification
6.4 CERTIFICATION
6.5 OVERHAUL AND REPAIR PROCEDURES
6.5.1 Motor windings
6.5.2 Overhaul of Ex ‚n™-Non-sparking motors
6.5.3 Overhaul of Ex ‚n™-Non-sparking enclosures
6.5.4 Overhaul of electrical equipment installed within Ex ‚n™ non-sparking enclosures
SECTION 7 ENCAPSULATION (Ex 'm')
7.1 PRINCIPLES OF ENCAPSULATION (Ex ‚m™)
7.2 APPLICATION
7.3 REPAIR AND OVERHAUL
7.3.1 Associated protection techniques
7.3.2 Removal of encapsulation material
7.3.3 Replacement of components
7.3.4 Preparation for replacing encapsulation
7.3.5 Encapsulating material
7.3.6 Pouring encapsulation material
7.3.7 Visual inspection
7.4 RECLAMATION
7.5 MODIFICATIONS
SECTION 8 DUST EXCLUDING IGNITION-PROOF (DIP)
8.1 GENERAL
8.2 EQUIPMENT
8.2.1 Enclosures
8.2.2 Cable and conduit entries
8.2.3 Incomplete documentation/information
8.3 AUXILIARY EQUIPMENT
8.3.1 Dust-excluding brake units
8.3.2 Auxiliary devices
8.3.3 Light-transmitting parts
8.3.4 Encapsulated parts
8.3.5 Batteries
8.3.6 Lamps
8.3.7 Lampholders
8.3.8 Ballasts
8.3.9 Interlocks
8.4 MECHANICAL REPAIRS
8.4.1 Damage to components
8.4.2 Joints
8.4.3 Spigoted joints
8.4.4 Shafts and housings
8.4.5 Boots
8.4.6 Journals
8.4.7 Damaged stator cores
8.5 MODIFICATIONS
8.6 CERTIFICATION
8.7 OVERHAUL AND REPAIR PROCEDURES
8.7.1 Motor windings
8.7.2 Overhaul of DIP motors
8.7.3 Overhaul of DIP enclosures
8.7.4 Overhaul of DIP electrical equipment installed within DIP enclosures
SECTION 9 USER INFORMATION
9.1 SCOPE
9.2 GENERAL REPAIR/OVERHAUL INFORMATION
9.2.1 General
9.2.2 Certification
9.2.3 Overhaul and examination reports
9.2.4 Overhaul frequency
9.3 SPECIFIC INFORMATION
9.3.1 General
9.3.2 Flameproof
9.4 DECIDING ON REPAIR OR REPLACEMENT
APPENDIX A - REQUIREMENTS FOR REPAIR AND OVERHAUL SERVICE FACILITIES
A1 SCOPE
A2 REQUIREMENTS FOR SERVICE FACILITIES
A2.1 Type of service facility
A2.2 Personnel
A2.3 Facilities
APPENDIX B - PRINCIPLES OF FLAMEPROOF ENCLOSURES (Ex ‚d™)
B1 INTRODUCTION
B2 CHARACTERISTICS OF FLAMEPROOF ENCLOSURES
B3 OVERHAUL OF FLAMEPROOF ENCLOSURES
B3.1 General
B3.2 Flameproof motors
B3.3 Maximum surface temperature
B3.4 Fixing bolts, studs and nuts
B3.5 Breathing devices
APPENDIX C - PRINCIPLES OF INCREASED SAFETY (Ex ‚e™)
C1 INTRODUCTION
C2 ARCING OR SPARKING PARTS
C3 INSULATION
C4 TEMPERATURE
C5 TERMINALS AND TERMINATIONS
APPENDIX D - IDENTIFICATION OF REPAIRED EQUIPMENT
D1 TRACEABILITY
D1.1 General
D1.2 Minimum marking
D1.3 Form of marking
D1.4 Subsequent overhauls
APPENDIX E - TESTS OF JOINT SURFACES USING STRAIGHTEDGES
APPENDIX F - CORROSION OR SURFACE INDENTATION TOLERANCES
APPENDIX G - OVER-PRESSURE TEST
G1 INTRODUCTION
G2 TEST PROCEDURE
G3 REPORTING OF RESULTS
G4 INTERPRETATION OF RESULTS
APPENDIX H - EXAMPLES OF OVER-PRESSURE TEST RIGS
APPENDIX I - TYPICAL REPAIR/OVERHAUL AND EXAMINATION REPORT FOR FLAMEPROOF MOTORS (Ex ‚d™)
APPENDIX J - CHECK OF CIRCULAR FLANGES, SPIGOTS AND HOLES
J1 SCOPE
APPENDIX K - TYPICAL REPAIR/OVERHAUL AND EXAMINATION REPORT FOR FLAMEPROOF ENCLOSURE (Ex ‚d™)
APPENDIX L - TYPICAL REPAIR/OVERHAUL AND EXAMINATION REPORT FOR ELECTRICAL EQUIPMENT INSTALLED WITHIN FLAMEPROOF...
APPENDIX M - PRINCIPLES OF INTRINSIC SAFETY (Ex ‚i™)
M1 INTRODUCTION
M2 CHARACTERISTICS OF INTRINSIC SAFETY
M2.1 General
M2.2 Groups
M2.3 Categories
M2.4 Intrinsically safe electrical equipment and systems
M2.5 Safety barriers
M2.6 Testing/assessment
M3 OVERHAUL OF INTRINSIC SAFETY EQUIPMENT
APPENDIX N - TYPICAL REPAIR/OVERHAUL AND EXAMINATION REPORT FOR INTRINSICALLY SAFE EQUIPMENT (Ex ‚i™)
APPENDIX O - TYPICAL REPAIR/OVERHAUL AND EXAMINATION REPORT FOR INCREASED SAFETY MOTORS (Ex ‚e™)
APPENDIX P - TYPICAL REPAIR/OVERHAUL AND EXAMINATION REPORT FOR INCREASED SAFETY ENCLOSURES (Ex ‚e™)
APPENDIX Q - TYPICAL OVERHAUL AND EXAMINATION REPORT FOR ELECTRICAL EQUIPMENT INSTALLED WITHIN INCREASED SAFETY ENCLOSURES
APPENDIX R - TYPICAL REPAIR/OVERHAUL AND EXAMINATION REPORT FOR PRESSURIZED ENCLOSURES INCLUDING PRESSURIZED...
APPENDIX S - TYPICAL REPAIR/OVERHAUL AND EXAMINATION REPORT FOR NON-SPARKING MOTORS (Ex ‚n™)
APPENDIX T - A TYPICAL REPAIR/OVERHAUL AND EXAMINATION REPORT FOR NON-SPARKING ENCLOSURES (Ex ‚n™)
APPENDIX U - TYPICAL REPAIR/OVERHAUL AND EXAMINATION REPORT FOR ELECTRICAL EQUIPMENT INSTALLED WITHIN NON-SPARKING...
APPENDIX V - TYPICAL REPAIR/OVERHAUL AND EXAMINATION REPORT FOR ENCAPSULATED EQUIPMENT (Ex ‚m™)
APPENDIX W - TYPICAL REPAIR/OVERHAUL AND EXAMINATION REPORT FOR DIP MOTORS
APPENDIX X - TYPICAL REPAIR/OVERHAUL AND EXAMINATION REPORT FOR DIP ENCLOSURES
APPENDIX Y - TYPICAL REPAIR/OVERHAUL AND EXAMINATION REPORT FOR ELECTRICAL EQUIPMENT INSTALLED WITHIN DIP ENCLOSURES
APPENDIX Z - GUIDANCE FOR MEASUREMENTS IN FLAMEPROOF EQUIPMENT, WHEN REPAIRED/OVERHAULED
Z1 GENERAL
Z2 GUIDANCE FOR TOLERANCES
Z2.1 Shafts with rolling-element bearings
Z2.2 Flanged joints
Previous versions
Keep me up-to-date
Sign up to receive updates when there are changes to this standard
References
Electrical equipment for mines and quarries - Substations
Related Information
Electricity (Safety) Regulations 2010
Ministry: WorkSafe New Zealand: Energy Safety
Section: Schedule 8, Clause 40
Citation context:40. Overhaul of mining electrical equipment in ERZ0 or ERZ1: Any overhaul of mining electrical equipment installed or used, or to be installed or used, in an ERZ0 or ERZ1 must be done in accordance with AS/NZS 3800.
Electricity (Safety) Regulations 2010
Ministry: WorkSafe New Zealand: Energy Safety
Section: Schedule 2
Citation context:AS/NZS 3800 means AS/NZS 3800:2005
Similar Standards
-
AS/NZS 1299:2009
Electrical equipment for mines and quarries - Explosion-protected three-phase restrained plugs and receptacles for working voltages up to and including 3.3 kV
-
AS/NZS 1299:2009 A1
Electrical equipment for mines and quarries - Explosion-protected three-phase restrained plugs and receptacles for working voltages up to and including 3.3 kV: Amendment 1:2012 -
AS/NZS 1300:2009
Electrical equipment for mines and quarries - Bolted explosion-protected three-phase cable coupling devices
-
AS/NZS 1300:2009 A1
Electrical equipment for mines and quarries - Bolted explosion-protected three-phase cable coupling devices: Amendment 1:2012
AS/NZS 3800:2005 ELECTRICAL EQUIPMENT FOR EXPLOSIVE ATMOSPHERES-REPAIR AND OVERHAUL
PREFACE
CONTENTS
FOREWORD
SECTION 1 SCOPE AND GENERAL
1.1 SCOPE
1.2 APPLICATION
1.3 REFERENCED DOCUMENTS
1.4 DEFINITIONS
1.4.1 Approved
1.4.2 Australian Qualification Framework (AQF)
1.4.3 Certification
1.4.4 Competent person
1.4.5 Encapsulation (Ex ‚m™)
1.4.6 Enclosure, dust-excluding ignition-proof (DIP enclosure)
1.4.7 Equipment
1.4.8 Explosion-protection
1.4.9 Explosive gas atmosphere
1.4.10 Ex Testing Laboratory (ExTL)
1.4.11 Flameproof enclosure (Ex ‚d™)
1.4.12 Flameproof joint
1.4.13 Gap (diametral clearance)
1.4.14 Hazardous area
1.4.15 Increased safety protection (Ex ‚e™)
1.4.16 Intrinsically safe electrical equipment (Ex ‚i™)
1.4.17 Length of flamepath (width of joint)
1.4.18 Maintenance
1.4.19 Maximum surface temperature
1.4.20 Modification
1.4.21 Non-sparking protection (Ex ‚n™)
1.4.22 Operating rod (spindle)
1.4.23 Overhaul
1.4.24 Overhaul and examination report
1.4.25 Pressure piling
1.4.26 Pressurization (Ex ‚p™)
1.4.27 Recognized service facility
1.4.28 Repair
1.4.29 Replacement
1.4.30 Sand-filled enclosure (Ex ‚q™)
1.4.31 Special protection (Ex ‚s™)
1.4.32 Temperature classification
1.4.33 Verification dossier
1.5 DOCUMENTATION/INFORMATION
1.5.1 General
1.5.2 Where certification documentation is not available but sufficient information is available to identify the type of...
1.5.3 Insufficient information
1.5.4 Traceability/marking
1.5.5 Variation from certification documents
1.5.6 Acceptance criteria
1.6 MIXED EXPLOSION-PROTECTION TECHNIQUES
1.7 GROUPING OF EXPLOSION-PROTECTED ELECTRICAL EQUIPMENT
1.7.1 Group designation
1.7.2 Group II subdivision
1.8 ROLE OF COMPETENT PERSONS
SECTION 2 FLAMEPROOF ENCLOSURES (Ex 'd')
2.1 GENERAL
2.1.1 Flameproof enclosures
2.1.2 Use of greases
2.1.3 Fixing bolts, studs and nuts
2.1.4 Attachments
2.1.5 Replacement
2.1.6 Machining
2.1.7 Joint surfaces
2.1.8 Mixed protection techniques
2.2 CERTIFICATION
2.2.1 General
2.2.2 Flameproof tests
2.3 CATEGORIES OF WORK
2.3.1 General
2.3.2 Overhaul-No repair
2.3.3 Overhaul-Repair
2.3.4 Modifications
2.4 OVER-PRESSURE TESTING
2.4.1 General
2.4.2 Water-cooled motors and enclosures
2.4.3 Enclosures with screwed covers
2.5 OVERHAUL AND REPAIR PROCEDURES
2.5.1 Overhaul of Ex ‚d™-Flameproof motors
2.5.2 Overhaul of Ex™d™-Flameproof enclosures
2.5.3 Overhaul of electrical equipment installed within Ex ‚d™ enclosures
SECTION 3 INTRINSIC SAFETY(Ex 'i')
3.1 GENERAL
3.2 EQUIPMENT
3.2.1 Enclosures
3.2.2 Ingress protection
3.2.3 Plugs and sockets
3.2.4 Terminations
3.2.5 Fuses
3.2.6 Printed circuit boards
3.2.7 Optocouplers
3.2.8 Piezo-electric devices
3.2.9 Multi-core cables
3.2.10 Fibre optic cable
3.2.11 Electrical parts
3.2.12 Batteries
3.2.13 Transformers
3.2.14 Encapsulated parts
3.2.15 Non-electrical parts
3.3 MODIFICATIONS
3.4 OVERHAUL AND REPAIR PROCEDURES
3.4.1 General procedures
3.4.2 Specific procedures
SECTION 4 INCREASED SAFETY (Ex 'e')
4.1 GENERAL
4.2 EQUIPMENT
4.2.1 Enclosures
4.2.2 Ingress protection
4.2.3 Plugs and sockets
4.2.4 Terminations
4.2.5 Internal connections
4.2.6 Electrical parts
4.2.7 Batteries
4.2.8 Transformers
4.2.9 Light transmitting parts
4.2.10 Lamps
4.2.11 Lampholders
4.2.12 Ballasts and capacitors
4.2.13 Encapsulated parts
4.2.14 Insulation
4.2.15 Winding connections
4.3 MODIFICATIONS
4.3.1 Modifications permitted by certification
4.3.2 Modifications not permitted within certification
4.4 CERTIFICATION
4.5 OVERHAUL AND REPAIR PROCEDURES
4.5.1 Motor windings
4.5.2 Overhaul of Ex ‚e™-Increased safety motors
4.5.3 Overhaul of Ex ‚e™-Increased safety enclosures
4.5.4 Overhaul of electrical equipment installed within Ex ‚e™ enclosures
SECTION 5 PRESSURIZED ENCLOSURES (Ex ‚p™)
5.1 GENERAL
5.2 PRESSURIZATION
5.3 ENCLOSURES
5.3.1 Materials
5.3.2 Joints in the enclosure
5.3.3 Gaskets and seals
5.3.4 Fasteners
5.3.5 Cable entries
5.4 TEMPERATURE RATING
5.4.1 Lighting fittings
5.4.2 Heat-generating equipment
5.5 OVERHAUL AND REPAIR PROCEDURES
SECTION 6 NON-SPARKING (Ex 'n')
6.1 GENERAL
6.2 EQUIPMENT
6.2.1 Enclosures
6.2.2 Ingress protection
6.2.3 Plugs and sockets
6.2.4 Terminations
6.2.5 Internal connections
6.2.6 Electrical parts
6.2.7 Batteries
6.2.8 Transformers
6.2.9 Light-transmitting parts
6.2.10 Lamps
6.2.11 Lampholders
6.2.12 Ballasts and capacitors
6.2.13 Encapsulated parts
6.2.14 Insulation
6.2.15 Winding connections
6.3 MODIFICATIONS
6.3.1 Modifications permitted by certification
6.3.2 Modifications not permitted within certification
6.4 CERTIFICATION
6.5 OVERHAUL AND REPAIR PROCEDURES
6.5.1 Motor windings
6.5.2 Overhaul of Ex ‚n™-Non-sparking motors
6.5.3 Overhaul of Ex ‚n™-Non-sparking enclosures
6.5.4 Overhaul of electrical equipment installed within Ex ‚n™ non-sparking enclosures
SECTION 7 ENCAPSULATION (Ex 'm')
7.1 PRINCIPLES OF ENCAPSULATION (Ex ‚m™)
7.2 APPLICATION
7.3 REPAIR AND OVERHAUL
7.3.1 Associated protection techniques
7.3.2 Removal of encapsulation material
7.3.3 Replacement of components
7.3.4 Preparation for replacing encapsulation
7.3.5 Encapsulating material
7.3.6 Pouring encapsulation material
7.3.7 Visual inspection
7.4 RECLAMATION
7.5 MODIFICATIONS
SECTION 8 DUST EXCLUDING IGNITION-PROOF (DIP)
8.1 GENERAL
8.2 EQUIPMENT
8.2.1 Enclosures
8.2.2 Cable and conduit entries
8.2.3 Incomplete documentation/information
8.3 AUXILIARY EQUIPMENT
8.3.1 Dust-excluding brake units
8.3.2 Auxiliary devices
8.3.3 Light-transmitting parts
8.3.4 Encapsulated parts
8.3.5 Batteries
8.3.6 Lamps
8.3.7 Lampholders
8.3.8 Ballasts
8.3.9 Interlocks
8.4 MECHANICAL REPAIRS
8.4.1 Damage to components
8.4.2 Joints
8.4.3 Spigoted joints
8.4.4 Shafts and housings
8.4.5 Boots
8.4.6 Journals
8.4.7 Damaged stator cores
8.5 MODIFICATIONS
8.6 CERTIFICATION
8.7 OVERHAUL AND REPAIR PROCEDURES
8.7.1 Motor windings
8.7.2 Overhaul of DIP motors
8.7.3 Overhaul of DIP enclosures
8.7.4 Overhaul of DIP electrical equipment installed within DIP enclosures
SECTION 9 USER INFORMATION
9.1 SCOPE
9.2 GENERAL REPAIR/OVERHAUL INFORMATION
9.2.1 General
9.2.2 Certification
9.2.3 Overhaul and examination reports
9.2.4 Overhaul frequency
9.3 SPECIFIC INFORMATION
9.3.1 General
9.3.2 Flameproof
9.4 DECIDING ON REPAIR OR REPLACEMENT
APPENDIX A - REQUIREMENTS FOR REPAIR AND OVERHAUL SERVICE FACILITIES
A1 SCOPE
A2 REQUIREMENTS FOR SERVICE FACILITIES
A2.1 Type of service facility
A2.2 Personnel
A2.3 Facilities
APPENDIX B - PRINCIPLES OF FLAMEPROOF ENCLOSURES (Ex ‚d™)
B1 INTRODUCTION
B2 CHARACTERISTICS OF FLAMEPROOF ENCLOSURES
B3 OVERHAUL OF FLAMEPROOF ENCLOSURES
B3.1 General
B3.2 Flameproof motors
B3.3 Maximum surface temperature
B3.4 Fixing bolts, studs and nuts
B3.5 Breathing devices
APPENDIX C - PRINCIPLES OF INCREASED SAFETY (Ex ‚e™)
C1 INTRODUCTION
C2 ARCING OR SPARKING PARTS
C3 INSULATION
C4 TEMPERATURE
C5 TERMINALS AND TERMINATIONS
APPENDIX D - IDENTIFICATION OF REPAIRED EQUIPMENT
D1 TRACEABILITY
D1.1 General
D1.2 Minimum marking
D1.3 Form of marking
D1.4 Subsequent overhauls
APPENDIX E - TESTS OF JOINT SURFACES USING STRAIGHTEDGES
APPENDIX F - CORROSION OR SURFACE INDENTATION TOLERANCES
APPENDIX G - OVER-PRESSURE TEST
G1 INTRODUCTION
G2 TEST PROCEDURE
G3 REPORTING OF RESULTS
G4 INTERPRETATION OF RESULTS
APPENDIX H - EXAMPLES OF OVER-PRESSURE TEST RIGS
APPENDIX I - TYPICAL REPAIR/OVERHAUL AND EXAMINATION REPORT FOR FLAMEPROOF MOTORS (Ex ‚d™)
APPENDIX J - CHECK OF CIRCULAR FLANGES, SPIGOTS AND HOLES
J1 SCOPE
APPENDIX K - TYPICAL REPAIR/OVERHAUL AND EXAMINATION REPORT FOR FLAMEPROOF ENCLOSURE (Ex ‚d™)
APPENDIX L - TYPICAL REPAIR/OVERHAUL AND EXAMINATION REPORT FOR ELECTRICAL EQUIPMENT INSTALLED WITHIN FLAMEPROOF...
APPENDIX M - PRINCIPLES OF INTRINSIC SAFETY (Ex ‚i™)
M1 INTRODUCTION
M2 CHARACTERISTICS OF INTRINSIC SAFETY
M2.1 General
M2.2 Groups
M2.3 Categories
M2.4 Intrinsically safe electrical equipment and systems
M2.5 Safety barriers
M2.6 Testing/assessment
M3 OVERHAUL OF INTRINSIC SAFETY EQUIPMENT
APPENDIX N - TYPICAL REPAIR/OVERHAUL AND EXAMINATION REPORT FOR INTRINSICALLY SAFE EQUIPMENT (Ex ‚i™)
APPENDIX O - TYPICAL REPAIR/OVERHAUL AND EXAMINATION REPORT FOR INCREASED SAFETY MOTORS (Ex ‚e™)
APPENDIX P - TYPICAL REPAIR/OVERHAUL AND EXAMINATION REPORT FOR INCREASED SAFETY ENCLOSURES (Ex ‚e™)
APPENDIX Q - TYPICAL OVERHAUL AND EXAMINATION REPORT FOR ELECTRICAL EQUIPMENT INSTALLED WITHIN INCREASED SAFETY ENCLOSURES
APPENDIX R - TYPICAL REPAIR/OVERHAUL AND EXAMINATION REPORT FOR PRESSURIZED ENCLOSURES INCLUDING PRESSURIZED...
APPENDIX S - TYPICAL REPAIR/OVERHAUL AND EXAMINATION REPORT FOR NON-SPARKING MOTORS (Ex ‚n™)
APPENDIX T - A TYPICAL REPAIR/OVERHAUL AND EXAMINATION REPORT FOR NON-SPARKING ENCLOSURES (Ex ‚n™)
APPENDIX U - TYPICAL REPAIR/OVERHAUL AND EXAMINATION REPORT FOR ELECTRICAL EQUIPMENT INSTALLED WITHIN NON-SPARKING...
APPENDIX V - TYPICAL REPAIR/OVERHAUL AND EXAMINATION REPORT FOR ENCAPSULATED EQUIPMENT (Ex ‚m™)
APPENDIX W - TYPICAL REPAIR/OVERHAUL AND EXAMINATION REPORT FOR DIP MOTORS
APPENDIX X - TYPICAL REPAIR/OVERHAUL AND EXAMINATION REPORT FOR DIP ENCLOSURES
APPENDIX Y - TYPICAL REPAIR/OVERHAUL AND EXAMINATION REPORT FOR ELECTRICAL EQUIPMENT INSTALLED WITHIN DIP ENCLOSURES
APPENDIX Z - GUIDANCE FOR MEASUREMENTS IN FLAMEPROOF EQUIPMENT, WHEN REPAIRED/OVERHAULED
Z1 GENERAL
Z2 GUIDANCE FOR TOLERANCES
Z2.1 Shafts with rolling-element bearings
Z2.2 Flanged joints
Previous versions
AS/NZS 3800:2005
Online Library subscription pricing
The cost of your subscription will depend on which standards you want to access, and how many people in your organisation need to be able to access the Online Library subscription at the same time (concurrent users). During your subscription period, we are also able to make any necessary changes and ensure you are aware of any pricing changes that result. For a quote, contact our Online Library team by emailing onlinelibrary@standards.govt.nz.