ISO 11365:2017
Petroleum and related products — Requirements and guidance for the maintenance of triaryl phosphate ester turbine control fluids
ISO 11365:2017 is applicable to the use of triaryl phosphate esters as fire-resistant fluids for turbine control and other hydraulic systems in power generation. These fluids fall under category HFDR of ISO 6743‑4[1].
ISO 11365:2017 is intended to:
- assist the power equipment operator to maintain the fluid in a condition that will ensure the safe and reliable operation of the turbine while maximizing fluid life;
- recommend procedures for examining consignments of new fluid and monitoring the fluid in use;
- provide information on the safe handling, storage and disposal of the fluid;
- offer background information on the causes of fluid degradation.
| Get this standard | Prices exclude GST | |
|---|---|---|
| PDF ( Single user document) |
$126.00 NZD
|
|
| HardCopy |
$173.00 NZD
|
|
| Networkable PDF |
Price varies
|
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Description of triaryl phosphate ester fluids
5 Health and safety precautions
5.1 Fluid handling
5.2 Waste disposal
6 Fire hazards
6.1 General points
6.2 Methods of extinguishing fires
7 Compatibility of materials
7.1 Seals, paints and gaskets
7.2 Electrical cable insulation
8 Factors affecting service life
8.1 General
8.2 System design
8.3 System operating conditions
8.4 System maintenance
8.5 Fluid contamination
8.5.1 General
8.5.2 Air
8.5.3 Water
8.5.4 Particulates
8.5.5 Mineral oil
8.5.6 Metal soaps
8.5.7 Chlorinated materials
8.6 Fluid condition monitoring
8.7 Fluid purification
8.8 Fluid top up
9 Delivery and storage
10 Flushing the system
11 Fluid sampling
11.1 General
11.2 Containers
11.3 Sampling in service
11.3.1 General
11.3.2 Sampling points
11.3.3 Precautions to be taken when sampling from a line
11.3.4 Sampling from a tank or reservoir
11.4 Sampling of fresh fluid
11.5 Labelling
12 Recommended procedures for fluid monitoring
12.1 Appearance and colour
12.2 Water content
12.3 Neutralization number (Acid number - AN)
12.4 Fluid cleanliness
12.5 Direct current resistivity (volume resistivity)
12.6 Chlorine content
12.7 Mineral oil content
12.8 Viscosity
12.9 Air release
12.10 Foaming
13 Examination of new fluid
13.1 Acceptance tests for new fluid
13.2 Acceptance requirements after installation of a new fluid charge
14 Examination of used fluid
14.1 General
14.2 Trend analysis
Bibliography
Keep me up-to-date
Sign up to receive updates when there are changes to this standard
Related Information
Similar Standards
-
BS 2000-313:2001
Methods of test for petroleum and its products, Determination of air release of lubricating and hydraulic oils
-
BS 5540-3:1978
Specification for evaluating particulate contamination of hydraulic fluids, Methods of bottling fluid samples
-
BS 5540-6:1990
Evaluating particulate contamination of hydraulic fluids, Method of calibrating liquid automatic particle-count instruments (using mono-sized latex spheres)
-
BS 8465:2010
Hydraulic fluid power. Monitoring the level of particulate contamination. Comparison membrane technique
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Description of triaryl phosphate ester fluids
5 Health and safety precautions
5.1 Fluid handling
5.2 Waste disposal
6 Fire hazards
6.1 General points
6.2 Methods of extinguishing fires
7 Compatibility of materials
7.1 Seals, paints and gaskets
7.2 Electrical cable insulation
8 Factors affecting service life
8.1 General
8.2 System design
8.3 System operating conditions
8.4 System maintenance
8.5 Fluid contamination
8.5.1 General
8.5.2 Air
8.5.3 Water
8.5.4 Particulates
8.5.5 Mineral oil
8.5.6 Metal soaps
8.5.7 Chlorinated materials
8.6 Fluid condition monitoring
8.7 Fluid purification
8.8 Fluid top up
9 Delivery and storage
10 Flushing the system
11 Fluid sampling
11.1 General
11.2 Containers
11.3 Sampling in service
11.3.1 General
11.3.2 Sampling points
11.3.3 Precautions to be taken when sampling from a line
11.3.4 Sampling from a tank or reservoir
11.4 Sampling of fresh fluid
11.5 Labelling
12 Recommended procedures for fluid monitoring
12.1 Appearance and colour
12.2 Water content
12.3 Neutralization number (Acid number - AN)
12.4 Fluid cleanliness
12.5 Direct current resistivity (volume resistivity)
12.6 Chlorine content
12.7 Mineral oil content
12.8 Viscosity
12.9 Air release
12.10 Foaming
13 Examination of new fluid
13.1 Acceptance tests for new fluid
13.2 Acceptance requirements after installation of a new fluid charge
14 Examination of used fluid
14.1 General
14.2 Trend analysis
Bibliography