AS/NZS 3679.1:2016
Structural steel - Part 1: Hot-rolled bars and sections
Specifies the requirements for the production and supply of hot-rolled structural steel bars and sections. This Standard is intended for general structural and engineering applications. All grades specified in this Standard are suitable for welding in accordance with AS/NZS 1554, Parts 1, 2, 5 and 7; and fastening, as specified in AS 3990, AS 4100, AS/NZS 4600, AS 5100.6 and NZS 3404.
| Get this standard | Prices exclude GST | |
|---|---|---|
| PDF ( Single user document) |
$171.90 NZD
|
|
| HardCopy |
$191.00 NZD
|
|
| Networkable PDF |
Price varies
|
|
| Online Library ( Annual subscription) |
Info
Price varies
Online Library subscription information Online library subscriptions provide a cost-effective solution for organisations of any size to access the latest standards, offering 24/7 access to a personalised catalogue. The service ensures subscribers have have the most up-to-date version of selected standards, incluing automatic updates for any amendments or versions. Pricing is dependent on the chosen standards and the number of concurrent users, with discounts applied from the standards PDF price. For customised subscriptions or further inquiries, contact the Online Library team. |
PREFACE
CONTENTS
1 SCOPE
2 NORMATIVE REFERENCES
3 DEFINITIONS
3.1 Analysis
3.1.1 Cast analysis
3.1.2 Product analysis
3.2 Bars
3.3 Batch
3.4 Can
3.5 Crack
3.6 Defects
3.7 Factory production control
3.8 Heat
3.9 Imperfections
3.10 Inspection
3.11 Lap
3.12 Longitudinal direction
3.13 Manufacturer
3.14 May
3.15 Primary rolled product
3.16 Purchaser
3.17 Seams
3.18 Sections
3.19 Shall
3.20 Should
3.21 Supplier
3.22 Testing
3.23 Test piece
3.24 Test sample
3.25 Test specimen
3.26 Transverse direction
3.27 Type testing
4 DESIGNATION
5 MANUFACTURING PROCESS-STEEL FEED
6 CHEMICAL COMPOSITION
6.1 General
6.2 Cast analysis
6.3 Product analysis
6.4 Residual elements
7 MANUFACTURING TOLERANCES
7.1 Bars
7.2 Sections
8 FREEDOM FROM DEFECTS
8.1 General
8.2 Freedom from surface defects
8.2.1 General
8.2.2 Bars
8.2.3 Sections
8.3 Removal of surface defects
8.3.1 Bars
8.3.2 Sections
8.4 Weld repair of surface defects
8.4.1 General
8.4.2 Welding
9 TESTING
9.1 Selection of test samples
9.2 Position and orientation of test pieces
9.3 Preparation of test pieces for mechanical testing
9.3.1 General
9.3.2 Tensile test piece
9.3.3 Impact test piece
9.4 Mechanical testing
9.4.1 Tensile test
9.4.2 Charpy V-notch impact test
10 MECHANICAL PROPERTIES
10.1 Tensile tests
10.2 Impact test
11 IDENTIFICATION, TEST AND INSPECTION CERTIFICATES
11.1 Identification
11.1.1 Individual length markings
11.1.2 Bundle/pack markings
11.2 Test and inspection certificates
11.2.1 General
11.2.2 Transmission of test and inspection certificates by an intermediary
11.2.3 Qualifications on test and inspection certificates
11.2.4 Minimum requirements for test and inspection certificates
12 SAMPLING AND TESTING TO DEMONSTRATE PRODUCT CONFORMITY
13 ROUNDING OF NUMBERS
13.1 General
13.2 Tensile properties
14 MANIPULATION
15 SECTION DESIGNATIONS, DIMENSIONS AND MASSES
APPENDIX A - PURCHASING GUIDELINES
A1 GENERAL
A2 INFORMATION TO BE SUPPLIED BY THE PURCHASER
A3 NON-DESTRUCTIVE EXAMINATION
A4 INSPECTION
APPENDIX B - PRODUCT CONFORMITY
B1 SCOPE
B2 INITIAL TYPE TESTING
B2.1 General
B2.2 Minimum sampling and testing plan
B3 PRODUCTION TESTING AND INSPECTIONS
B3.1 Minimum batch testing and inspections
B3.2 Statistical sampling
B3.3 Tensile tests
B3.4 Impact tests
B4 Factory production control
B4.1 General
B4.2 Equipment
B4.3 Raw materials
B4.4 Product testing and evaluation
B5 NONCONFORMING PRODUCTS
B5.1 General
B5.2 Retests
B5.3 Repair
B6 DOCUMENTATION
APPENDIX C - COLD-BENDING OF ROUNDS, FLATS AND SQUARES DURING FABRICATION
APPENDIX D - SECTION DESIGNATIONS DIMENSIONS AND MASSES
APPENDIX E - MEASUREMENT OF CAMBER AND SWEEP IN UNIVERSAL SECTIONS
E1 GENERAL
E2 CAMBER
E3 SWEEP
APPENDIX F - STEEL FOR SEISMIC AND FRACTURE CRITICAL APPLICATIONS (NEW ZEALAND ONLY)
F1 ADDITIONAL REQUIREMENTS FOR SEISMIC AND FRACTURE CRITICAL APPLICATIONS
F2 STEEL FOR SEISMIC APPLICATIONS
F3 STEEL FOR FRACTURE CRITICAL MEMBERS
BIBLIOGRAPHY
Previous versions
Keep me up-to-date
Sign up to receive updates when there are changes to this standard
Related Information
Approved code of practice for flammable liquids road tank wagons
Ministry: WorkSafe New Zealand
Section: 3.1
Citation context:STEEL Steel is of a quality suitable for the conditions of use and complies with the requirements of the following Standards (or equivalent), as appropriate:... ...AS/NZS 3679.1: 2016 Structural steel – Part 1: Hot-rolled bars and sections...
Building Code Compliance Document B1
Ministry: Ministry of Business, Innovation, and Employment - Building Systems Performance (BSP)
Section: VM1
Citation context:Approved code of practice for flammable liquids road tank wagons
Ministry: WorkSafe New Zealand
Section: 1.8 References
Citation context:AS/NZS 3679.1:2016 Structural steel – Part 1: Hot-rolled bars and sections
Similar Standards
-
AS/NZS 1163:2016
Cold-formed structural steel hollow sections -
AS/NZS 1163:2016 A1
Cold-formed structural steel hollow sections: Amendment 1:2017 -
AS/NZS 3678:2016
Structural steel - Hot-rolled plates, floorplates and slabs -
AS/NZS 3678:2016A1
Structural steel - Hot-rolled plates, floorplates and slabs: Amendment 1:2017
PREFACE
CONTENTS
1 SCOPE
2 NORMATIVE REFERENCES
3 DEFINITIONS
3.1 Analysis
3.1.1 Cast analysis
3.1.2 Product analysis
3.2 Bars
3.3 Batch
3.4 Can
3.5 Crack
3.6 Defects
3.7 Factory production control
3.8 Heat
3.9 Imperfections
3.10 Inspection
3.11 Lap
3.12 Longitudinal direction
3.13 Manufacturer
3.14 May
3.15 Primary rolled product
3.16 Purchaser
3.17 Seams
3.18 Sections
3.19 Shall
3.20 Should
3.21 Supplier
3.22 Testing
3.23 Test piece
3.24 Test sample
3.25 Test specimen
3.26 Transverse direction
3.27 Type testing
4 DESIGNATION
5 MANUFACTURING PROCESS-STEEL FEED
6 CHEMICAL COMPOSITION
6.1 General
6.2 Cast analysis
6.3 Product analysis
6.4 Residual elements
7 MANUFACTURING TOLERANCES
7.1 Bars
7.2 Sections
8 FREEDOM FROM DEFECTS
8.1 General
8.2 Freedom from surface defects
8.2.1 General
8.2.2 Bars
8.2.3 Sections
8.3 Removal of surface defects
8.3.1 Bars
8.3.2 Sections
8.4 Weld repair of surface defects
8.4.1 General
8.4.2 Welding
9 TESTING
9.1 Selection of test samples
9.2 Position and orientation of test pieces
9.3 Preparation of test pieces for mechanical testing
9.3.1 General
9.3.2 Tensile test piece
9.3.3 Impact test piece
9.4 Mechanical testing
9.4.1 Tensile test
9.4.2 Charpy V-notch impact test
10 MECHANICAL PROPERTIES
10.1 Tensile tests
10.2 Impact test
11 IDENTIFICATION, TEST AND INSPECTION CERTIFICATES
11.1 Identification
11.1.1 Individual length markings
11.1.2 Bundle/pack markings
11.2 Test and inspection certificates
11.2.1 General
11.2.2 Transmission of test and inspection certificates by an intermediary
11.2.3 Qualifications on test and inspection certificates
11.2.4 Minimum requirements for test and inspection certificates
12 SAMPLING AND TESTING TO DEMONSTRATE PRODUCT CONFORMITY
13 ROUNDING OF NUMBERS
13.1 General
13.2 Tensile properties
14 MANIPULATION
15 SECTION DESIGNATIONS, DIMENSIONS AND MASSES
APPENDIX A - PURCHASING GUIDELINES
A1 GENERAL
A2 INFORMATION TO BE SUPPLIED BY THE PURCHASER
A3 NON-DESTRUCTIVE EXAMINATION
A4 INSPECTION
APPENDIX B - PRODUCT CONFORMITY
B1 SCOPE
B2 INITIAL TYPE TESTING
B2.1 General
B2.2 Minimum sampling and testing plan
B3 PRODUCTION TESTING AND INSPECTIONS
B3.1 Minimum batch testing and inspections
B3.2 Statistical sampling
B3.3 Tensile tests
B3.4 Impact tests
B4 Factory production control
B4.1 General
B4.2 Equipment
B4.3 Raw materials
B4.4 Product testing and evaluation
B5 NONCONFORMING PRODUCTS
B5.1 General
B5.2 Retests
B5.3 Repair
B6 DOCUMENTATION
APPENDIX C - COLD-BENDING OF ROUNDS, FLATS AND SQUARES DURING FABRICATION
APPENDIX D - SECTION DESIGNATIONS DIMENSIONS AND MASSES
APPENDIX E - MEASUREMENT OF CAMBER AND SWEEP IN UNIVERSAL SECTIONS
E1 GENERAL
E2 CAMBER
E3 SWEEP
APPENDIX F - STEEL FOR SEISMIC AND FRACTURE CRITICAL APPLICATIONS (NEW ZEALAND ONLY)
F1 ADDITIONAL REQUIREMENTS FOR SEISMIC AND FRACTURE CRITICAL APPLICATIONS
F2 STEEL FOR SEISMIC APPLICATIONS
F3 STEEL FOR FRACTURE CRITICAL MEMBERS
BIBLIOGRAPHY
Previous versions
AS/NZS 3679.1:2016
Online Library subscription information
Online library subscriptions provide a cost-effective solution for organisations of any size to access the latest standards, offering 24/7 access to a personalised catalogue. The service ensures subscribers have have the most up-to-date version of selected standards, incluing automatic updates for any amendments or versions. Pricing is dependent on the chosen standards and the number of concurrent users, with discounts applied from the standards PDF price. For customised subscriptions or further inquiries, contact the Online Library team.