AS/NZS 1158.6:2010
Road lighting - Luminaires
Sets out the requirements for the design, construction, performance and testing of road lighting luminaires to ensure that they will be suitable for the operating and environmental conditions to which they will be subjected in service. Road lighting luminaires must withstand, and be capable of operating under, adverse conditions, including the effects of salt spray, industrially contaminated atmospheres, fog, smoke, dust storms, snow, ultraviolet radiation, driving rain, wind and traffic-induced vibration.
| Get this standard | Prices exclude GST | |
|---|---|---|
| PDF ( Single user document) |
$171.90 NZD
|
|
| HardCopy |
$191.00 NZD
|
|
| Networkable PDF |
Price varies
|
|
| Online Library ( Annual subscription) |
Info
Price varies
Online Library subscription information Online library subscriptions provide a cost-effective solution for organisations of any size to access the latest standards, offering 24/7 access to a personalised catalogue. The service ensures subscribers have have the most up-to-date version of selected standards, incluing automatic updates for any amendments or versions. Pricing is dependent on the chosen standards and the number of concurrent users, with discounts applied from the standards PDF price. For customised subscriptions or further inquiries, contact the Online Library team. |
AS/NZS 1158.6:2010 LIGHTING FOR ROADS AND PUBLIC SPACES - LUMINAIRES
PREFACE
CONTENTS
SECTION 1 SCOPE AND GENERAL
1.1 SCOPE
1.2 APPLICATION
1.3 REFERENCED DOCUMENTS
1.4 DEFINITIONS
1.5 ENVIRONMENTAL CONDITIONS
1.6 MARKING
1.6.1 General
1.6.2 Information on interior of luminaire
1.6.3 Coded information on exterior of luminaire
1.6.4 Additional internal marking for luminaires with high pressure sodium lamps
1.7 ADDITIONAL INFORMATION
SECTION 2 MECHANICAL AND PHYSICAL REQUIREMENTS
2.1 SCOPE OF SECTION
2.2 GENERAL DESIGN AND ARRANGEMENT
2.2.1 Form and construction
2.2.2 Required ingress protection
2.3 CONSTRUCTION
2.3.1 Resistance to vandalism
2.3.2 Other aspects
2.4 LUMINAIRE BODY
2.4.1 Material
2.4.2 Component fixing devices
2.4.3 Seals and gaskets
2.5 VISORS
2.5.1 Attachment to luminaire body
2.5.2 Materials and construction
2.6 OPTICAL SYSTEM
2.7 CONTROL GEAR, SUPPLY CABLING TERMINATION COMPARTMENT
2.8 COMPARTMENT COVERS
2.9 FIXING SPIGOT ENTRY
2.9.1 Luminaires other than top-entry type
2.9.2 Top-entry luminaires
2.10 MAXIMUM MASS OF LUMINAIRES
2.10.1 Standard side-entry luminaires
2.10.2 Non-standard side-entry luminaires
2.10.3 Post-top luminaires
2.10.4 Top-entry luminaires
SECTION 3 ELECTRICAL WIRING AND COMPONENTS
3.1 SCOPE OF SECTION
3.2 CONTROL GEAR FOR HIGH INTENSITY DISCHARGE (HID) LAMPS
3.2.1 Ballasts
3.2.2 Igniters
3.3 CONTROL GEAR FOR FLUORESCENT LAMPS
3.4 REQUIREMENTS FOR HID LAMPS
3.4.1 Required lamp types
3.4.2 Lampholder requirements
3.5 REQUIREMENTS FOR FLUORESCENT LAMPS
3.5.1 Required lamp types
3.5.2 Lampholder requirements
3.6 ELECTRICAL SUPPLY
3.7 CABLE ENTRY
3.8 TERMINAL BLOCK
3.9 ARRANGEMENT OF CONTROL GEAR
3.9.1 Mounting of equipment
3.9.2 Removable control gear trays
3.10 SOCKET FOR PHOTOELECTRIC CELL SWITCH
3.10.1 Base type
3.10.2 Connection arrangement for luminaires with a D2 base
3.10.3 Colour coding of connecting wiring
3.10.4 Failure mode
3.11 INTERNAL WIRING
3.12 SPECIFIC ELECTRICAL SAFETY REQUIREMENTS
3.13 PROTECTION AGAINST ELECTRIC SHOCK
3.13.1 General
3.13.2 Testing of photoelectric-controlled luminaires
SECTION 4 ADDITIONAL REQUIREMENTS FOR PARTICULAR LUMINAIRES
4.1 OPTIONAL COMPONENTS (CATEGORY V AND CATEGORY P LUMINAIRES)
4.1.1 Power factor correction capacitors
4.1.2 Blocking inductor
4.1.3 Overcurrent protection
4.1.4 Interference suppression capacitors
SECTION 5 PERFORMANCE AND TESTING
5.1 SCOPE OF SECTION
5.2 TESTING OF PE CELL TYPE LUMINAIRES
5.3 BALLAST LOSSES
5.4 WIND FORCE TEST
5.4.1 Test conditions and procedure
5.4.2 Performance assessment
5.5 VIBRATION TESTING
5.5.1 Application
5.5.2 Test procedure
5.5.3 Application as type test
5.6 INGRESS PROTECTION TEST
5.7 RESISTANCE TO EXTERNAL MECHANICAL IMPACT
5.8 IMPULSE VOLTAGE TEST
5.8.1 Test conditions and procedure
5.8.2 Test criteria
5.9 THERMAL ENDURANCE AND THERMAL TESTING REQUIREMENTS
5.10 ADDITIONAL TESTS
SECTION 6 SUPPORTING DOCUMENTATION
6.1 SCOPE OF SECTION
6.2 GENERAL INFORMATION
6.3 PHOTOMETRIC INFORMATION
6.4 STATEMENTS OF COMPLIANCE
APPENDIX A - GUIDE TO MATERIALS AND TECHNOLOGIES
A1 INTRODUCTION
A2 BODY MATERIAL
A3 PLASTICS IN NON-LOAD-BEARING APPLICATIONS
A4 VISORS
A4.1 Visor material
A4.2 Self-cleaning glass visors
A5 CONTROL GEAR
A5.1 General
A5.2 Magnetic ballasts
A5.3 Electronic control gear
A5.4 Centralized road lighting control systems
A5.5 Control gear location
A6 LAMPS
A6.1 General
A6.2 High xenon or super high pressure sodium lamps
A6.3 Lampholders
A6.4 Light emitting diodes (LED)
APPENDIX B - LIST OF REFERENCED DOCUMENTS
APPENDIX C - INFORMATION RECOMMENDED TO BE SUPPLIED WITH ENQUIRY OR ORDER
APPENDIX D - POLE/BRACKET ARM END DETAIL FOR TOP-ENTRY LUMINAIRES
Previous versions
Keep me up-to-date
Register to receive notifications when updates are made to this standard.
References
Auxiliaries for lamps - Starting devices (other than glow starters) - Performance requirements
Limits and methods of measurement of radio disturbance characteristics of electrical lighting and similar equipment
Related Information
Similar Standards
-
AS/NZS 1158.0:2005
Lighting for roads and public spaces - Part 0: Introduction -
AS/NZS 1158.0:2005 A1
Lighting for roads and public spaces - Part 0: Introduction: Amendment 1 -
AS/NZS 1158.0:2005 A2
Lighting for roads and public spaces - Part 0: Introduction: Amendment 2 -
AS/NZS 1158.1.1:2022
Lighting for roads and public spaces - Vehicular traffic (Category V) lighting - Performance and design requirements
AS/NZS 1158.6:2010 LIGHTING FOR ROADS AND PUBLIC SPACES - LUMINAIRES
PREFACE
CONTENTS
SECTION 1 SCOPE AND GENERAL
1.1 SCOPE
1.2 APPLICATION
1.3 REFERENCED DOCUMENTS
1.4 DEFINITIONS
1.5 ENVIRONMENTAL CONDITIONS
1.6 MARKING
1.6.1 General
1.6.2 Information on interior of luminaire
1.6.3 Coded information on exterior of luminaire
1.6.4 Additional internal marking for luminaires with high pressure sodium lamps
1.7 ADDITIONAL INFORMATION
SECTION 2 MECHANICAL AND PHYSICAL REQUIREMENTS
2.1 SCOPE OF SECTION
2.2 GENERAL DESIGN AND ARRANGEMENT
2.2.1 Form and construction
2.2.2 Required ingress protection
2.3 CONSTRUCTION
2.3.1 Resistance to vandalism
2.3.2 Other aspects
2.4 LUMINAIRE BODY
2.4.1 Material
2.4.2 Component fixing devices
2.4.3 Seals and gaskets
2.5 VISORS
2.5.1 Attachment to luminaire body
2.5.2 Materials and construction
2.6 OPTICAL SYSTEM
2.7 CONTROL GEAR, SUPPLY CABLING TERMINATION COMPARTMENT
2.8 COMPARTMENT COVERS
2.9 FIXING SPIGOT ENTRY
2.9.1 Luminaires other than top-entry type
2.9.2 Top-entry luminaires
2.10 MAXIMUM MASS OF LUMINAIRES
2.10.1 Standard side-entry luminaires
2.10.2 Non-standard side-entry luminaires
2.10.3 Post-top luminaires
2.10.4 Top-entry luminaires
SECTION 3 ELECTRICAL WIRING AND COMPONENTS
3.1 SCOPE OF SECTION
3.2 CONTROL GEAR FOR HIGH INTENSITY DISCHARGE (HID) LAMPS
3.2.1 Ballasts
3.2.2 Igniters
3.3 CONTROL GEAR FOR FLUORESCENT LAMPS
3.4 REQUIREMENTS FOR HID LAMPS
3.4.1 Required lamp types
3.4.2 Lampholder requirements
3.5 REQUIREMENTS FOR FLUORESCENT LAMPS
3.5.1 Required lamp types
3.5.2 Lampholder requirements
3.6 ELECTRICAL SUPPLY
3.7 CABLE ENTRY
3.8 TERMINAL BLOCK
3.9 ARRANGEMENT OF CONTROL GEAR
3.9.1 Mounting of equipment
3.9.2 Removable control gear trays
3.10 SOCKET FOR PHOTOELECTRIC CELL SWITCH
3.10.1 Base type
3.10.2 Connection arrangement for luminaires with a D2 base
3.10.3 Colour coding of connecting wiring
3.10.4 Failure mode
3.11 INTERNAL WIRING
3.12 SPECIFIC ELECTRICAL SAFETY REQUIREMENTS
3.13 PROTECTION AGAINST ELECTRIC SHOCK
3.13.1 General
3.13.2 Testing of photoelectric-controlled luminaires
SECTION 4 ADDITIONAL REQUIREMENTS FOR PARTICULAR LUMINAIRES
4.1 OPTIONAL COMPONENTS (CATEGORY V AND CATEGORY P LUMINAIRES)
4.1.1 Power factor correction capacitors
4.1.2 Blocking inductor
4.1.3 Overcurrent protection
4.1.4 Interference suppression capacitors
SECTION 5 PERFORMANCE AND TESTING
5.1 SCOPE OF SECTION
5.2 TESTING OF PE CELL TYPE LUMINAIRES
5.3 BALLAST LOSSES
5.4 WIND FORCE TEST
5.4.1 Test conditions and procedure
5.4.2 Performance assessment
5.5 VIBRATION TESTING
5.5.1 Application
5.5.2 Test procedure
5.5.3 Application as type test
5.6 INGRESS PROTECTION TEST
5.7 RESISTANCE TO EXTERNAL MECHANICAL IMPACT
5.8 IMPULSE VOLTAGE TEST
5.8.1 Test conditions and procedure
5.8.2 Test criteria
5.9 THERMAL ENDURANCE AND THERMAL TESTING REQUIREMENTS
5.10 ADDITIONAL TESTS
SECTION 6 SUPPORTING DOCUMENTATION
6.1 SCOPE OF SECTION
6.2 GENERAL INFORMATION
6.3 PHOTOMETRIC INFORMATION
6.4 STATEMENTS OF COMPLIANCE
APPENDIX A - GUIDE TO MATERIALS AND TECHNOLOGIES
A1 INTRODUCTION
A2 BODY MATERIAL
A3 PLASTICS IN NON-LOAD-BEARING APPLICATIONS
A4 VISORS
A4.1 Visor material
A4.2 Self-cleaning glass visors
A5 CONTROL GEAR
A5.1 General
A5.2 Magnetic ballasts
A5.3 Electronic control gear
A5.4 Centralized road lighting control systems
A5.5 Control gear location
A6 LAMPS
A6.1 General
A6.2 High xenon or super high pressure sodium lamps
A6.3 Lampholders
A6.4 Light emitting diodes (LED)
APPENDIX B - LIST OF REFERENCED DOCUMENTS
APPENDIX C - INFORMATION RECOMMENDED TO BE SUPPLIED WITH ENQUIRY OR ORDER
APPENDIX D - POLE/BRACKET ARM END DETAIL FOR TOP-ENTRY LUMINAIRES
Previous versions
AS/NZS 1158.6:2010
Online Library subscription information
Online library subscriptions provide a cost-effective solution for organisations of any size to access the latest standards, offering 24/7 access to a personalised catalogue. The service ensures subscribers have have the most up-to-date version of selected standards, incluing automatic updates for any amendments or versions. Pricing is dependent on the chosen standards and the number of concurrent users, with discounts applied from the standards PDF price. For customised subscriptions or further inquiries, contact the Online Library team.