SA/SNZ TS 1158.6:2015
Lighting for roads and public spaces - Part 6: Luminaires - Performance
Sets out requirements for luminaires that are intended for use in Category V lighting schemes in accordance with AS/NZS 1158.1.1, and in Category P lighting schemes in accordance with AS/NZS 1158.3.1. This Technical Specification covers the design, construction, performance and marking of luminaires, and the provision of supporting documentation that are in addition to the safety requirements of AS/NZS 60598.2.3. This Technical Specification includes recommendations and requirements for the use of SSL light sources.
| Get this standard | Prices exclude GST | |
|---|---|---|
| PDF ( Single user document) |
$171.90 NZD
|
|
| HardCopy |
$191.00 NZD
|
|
| Networkable PDF |
Price varies
|
|
| Online Library ( Annual subscription) |
Info
Price varies
Online Library subscription information Online library subscriptions provide a cost-effective solution for organisations of any size to access the latest standards, offering 24/7 access to a personalised catalogue. The service ensures subscribers have have the most up-to-date version of selected standards, incluing automatic updates for any amendments or versions. Pricing is dependent on the chosen standards and the number of concurrent users, with discounts applied from the standards PDF price. For customised subscriptions or further inquiries, contact the Online Library team. |
SA/SNZ TS 1158.6:2015 LIGHTING FOR ROADS AND PUBLIC SPACES - LUMINAIRES-PERFORMANCE
PREFACE
CONTENTS
FOREWORD
SECTION 1 SCOPE AND GENERAL
1.1 SCOPE
1.2 REFERENCED DOCUMENTS
1.3 DEFINITIONS
1.3.1 Light-emitting diode (LED)
1.3.2 Luminaire efficacy rating (LER)
1.3.3 Solid state lighting (SSL)
1.4 VOLTAGE AND FREQUENCY RATING
1.5 ENVIRONMENTAL CONDITIONS
1.6 MARKING
1.6.1 General
1.6.2 Information on interior of luminaire
1.6.3 Coded information on exterior of luminaire
SECTION 2 MECHANICAL AND PHYSICAL REQUIREMENTS AND RECOMMENDATIONS
2.1 SCOPE OF SECTION
2.2 CONSTRUCTION
2.2.1 General
2.2.2 Required ingress protection
2.2.3 Impact resistance
2.3 LUMINAIRE BODY
2.3.1 Material
2.3.2 Component fixing devices
2.3.3 Gaskets
2.4 VISORS AND LENSES
2.4.1 Attachment to luminaire body
2.4.2 Materials and construction
2.5 OPTICAL SYSTEM
2.5.1 Installation
2.5.2 Materials
2.6 CONTROL GEAR, SUPPLY CABLING TERMINATION COMPARTMENT
2.7 COMPARTMENT COVERS
2.8 FIXING SPIGOT ENTRY
2.8.1 Luminaires other than top-entry type
2.8.2 Top-entry luminaires
2.9 SPIGOT SIZES AND MAXIMUM MASS OF LUMINAIRES
2.9.1 Side-entry luminaires
2.9.2 Post-top luminaires
2.9.3 Top-entry luminaires
2.10 SAIL AREA
SECTION 3 ELECTRICAL WIRING AND COMPONENTS
3.1 SCOPE OF SECTION
3.2 CONTROL GEAR
3.2.1 General
3.2.2 Magnetic ballasts for high intensity discharge (HID) lamps
3.2.3 Ignitors
3.2.4 Electronic control gear
3.3 REQUIREMENTS FOR HID LAMPS
3.3.1 Luminaires for high pressure sodium vapour lamps
3.3.2 Luminaires for high pressure mercury vapour lamps
3.3.3 Luminaires for metal halide lamps
3.3.4 Lampholder requirements
3.4 REQUIREMENTS FOR FLUORESCENT LAMPS
3.4.1 Required lamp types
3.4.2 Lampholder requirements
3.5 CABLE ENTRY
3.6 TERMINAL BLOCK
3.7 REMOVABLE CONTROL GEAR
3.8 LUMINAIRE SWITCHING
3.8.1 General
3.8.2 Connection arrangement for luminaires with a D2 base
3.8.3 Failure mode
3.9 INTERNAL WIRING
SECTION 4 ADDITIONAL REQUIREMENTS
4.1 SCOPE OF SECTION
4.2 POWER FACTOR REQUIREMENTS
4.3 BLOCKING INDUCTOR
4.4 OVERCURRENT PROTECTION
4.5 INTERFERENCE SUPPRESSION CAPACITORS
SECTION 5 PERFORMANCE AND TESTING
5.1 SCOPE OF SECTION
5.2 TESTING OF PE CELL TYPE LUMINAIRES
5.3 BALLAST LOSSES
5.4 VIBRATION TESTING
5.4.1 Application
5.4.2 Test procedures
5.4.3 Application as type test
5.5 IMPULSE VOLTAGE TEST
5.5.1 General
5.5.2 Test conditions and procedure
5.5.3 Test criteria
5.6 THERMAL ENDURANCE AND THERMAL TESTING REQUIREMENTS
5.7 PHOTOMETRIC TEST REQUIREMENTS FOR SSL LUMINAIRES
5.8 MINIMUM LUMINAIRE EFFICACY RATING
5.8.1 Luminaire efficacy rating (LER)
5.8.2 HID example calculation
5.8.3 SSL example calculation
SECTION 6 SUPPORTING DOCUMENTATION
6.1 SCOPE OF SECTION
6.2 GENERAL
6.3 PHOTOMETRIC DATA
6.4 STATEMENT OF COMPLIANCE
APPENDIX A - GUIDE TO EMERGING TECHNOLOGIES AND RELEVANT MATERIALS
A1 INTRODUCTION
A2 BODY MATERIAL
A3 PLASTICS IN NON-LOAD-BEARING APPLICATIONS
A4 VISORS
A4.1 Visor material
A4.2 Self-cleaning glass coatings
A5 CONTROL GEAR
A5.1 General
A5.2 Magnetic ballasts
A5.3 Electronic control gear
A5.4 Lighting control systems for roads and public spaces
A5.5 Control gear location
A6 LAMPS
A6.1 General
A6.2 High xenon or super high pressure sodium vapour lamps
A6.3 Lampholders
A6.4 Solid state lighting (SSL)
APPENDIX B - LIST OF REFERENCED DOCUMENTS
APPENDIX C - INFORMATION RECOMMENDED TO BE SUPPLIED WITH ENQUIRY OR ORDER
APPENDIX D - POLE/BRACKET ARM END DETAIL FOR TOP-ENTRY LUMINAIRES
BIBLIOGRAPHY
Keep me up-to-date
Register to receive notifications when updates are made to this standard.
Related Information
Similar Standards
-
AS/NZS 1158.0:2005
Lighting for roads and public spaces - Part 0: Introduction -
AS/NZS 1158.0:2005 A1
Lighting for roads and public spaces - Part 0: Introduction: Amendment 1 -
AS/NZS 1158.0:2005 A2
Lighting for roads and public spaces - Part 0: Introduction: Amendment 2 -
AS/NZS 1158.1.1:2022
Lighting for roads and public spaces - Vehicular traffic (Category V) lighting - Performance and design requirements
SA/SNZ TS 1158.6:2015 LIGHTING FOR ROADS AND PUBLIC SPACES - LUMINAIRES-PERFORMANCE
PREFACE
CONTENTS
FOREWORD
SECTION 1 SCOPE AND GENERAL
1.1 SCOPE
1.2 REFERENCED DOCUMENTS
1.3 DEFINITIONS
1.3.1 Light-emitting diode (LED)
1.3.2 Luminaire efficacy rating (LER)
1.3.3 Solid state lighting (SSL)
1.4 VOLTAGE AND FREQUENCY RATING
1.5 ENVIRONMENTAL CONDITIONS
1.6 MARKING
1.6.1 General
1.6.2 Information on interior of luminaire
1.6.3 Coded information on exterior of luminaire
SECTION 2 MECHANICAL AND PHYSICAL REQUIREMENTS AND RECOMMENDATIONS
2.1 SCOPE OF SECTION
2.2 CONSTRUCTION
2.2.1 General
2.2.2 Required ingress protection
2.2.3 Impact resistance
2.3 LUMINAIRE BODY
2.3.1 Material
2.3.2 Component fixing devices
2.3.3 Gaskets
2.4 VISORS AND LENSES
2.4.1 Attachment to luminaire body
2.4.2 Materials and construction
2.5 OPTICAL SYSTEM
2.5.1 Installation
2.5.2 Materials
2.6 CONTROL GEAR, SUPPLY CABLING TERMINATION COMPARTMENT
2.7 COMPARTMENT COVERS
2.8 FIXING SPIGOT ENTRY
2.8.1 Luminaires other than top-entry type
2.8.2 Top-entry luminaires
2.9 SPIGOT SIZES AND MAXIMUM MASS OF LUMINAIRES
2.9.1 Side-entry luminaires
2.9.2 Post-top luminaires
2.9.3 Top-entry luminaires
2.10 SAIL AREA
SECTION 3 ELECTRICAL WIRING AND COMPONENTS
3.1 SCOPE OF SECTION
3.2 CONTROL GEAR
3.2.1 General
3.2.2 Magnetic ballasts for high intensity discharge (HID) lamps
3.2.3 Ignitors
3.2.4 Electronic control gear
3.3 REQUIREMENTS FOR HID LAMPS
3.3.1 Luminaires for high pressure sodium vapour lamps
3.3.2 Luminaires for high pressure mercury vapour lamps
3.3.3 Luminaires for metal halide lamps
3.3.4 Lampholder requirements
3.4 REQUIREMENTS FOR FLUORESCENT LAMPS
3.4.1 Required lamp types
3.4.2 Lampholder requirements
3.5 CABLE ENTRY
3.6 TERMINAL BLOCK
3.7 REMOVABLE CONTROL GEAR
3.8 LUMINAIRE SWITCHING
3.8.1 General
3.8.2 Connection arrangement for luminaires with a D2 base
3.8.3 Failure mode
3.9 INTERNAL WIRING
SECTION 4 ADDITIONAL REQUIREMENTS
4.1 SCOPE OF SECTION
4.2 POWER FACTOR REQUIREMENTS
4.3 BLOCKING INDUCTOR
4.4 OVERCURRENT PROTECTION
4.5 INTERFERENCE SUPPRESSION CAPACITORS
SECTION 5 PERFORMANCE AND TESTING
5.1 SCOPE OF SECTION
5.2 TESTING OF PE CELL TYPE LUMINAIRES
5.3 BALLAST LOSSES
5.4 VIBRATION TESTING
5.4.1 Application
5.4.2 Test procedures
5.4.3 Application as type test
5.5 IMPULSE VOLTAGE TEST
5.5.1 General
5.5.2 Test conditions and procedure
5.5.3 Test criteria
5.6 THERMAL ENDURANCE AND THERMAL TESTING REQUIREMENTS
5.7 PHOTOMETRIC TEST REQUIREMENTS FOR SSL LUMINAIRES
5.8 MINIMUM LUMINAIRE EFFICACY RATING
5.8.1 Luminaire efficacy rating (LER)
5.8.2 HID example calculation
5.8.3 SSL example calculation
SECTION 6 SUPPORTING DOCUMENTATION
6.1 SCOPE OF SECTION
6.2 GENERAL
6.3 PHOTOMETRIC DATA
6.4 STATEMENT OF COMPLIANCE
APPENDIX A - GUIDE TO EMERGING TECHNOLOGIES AND RELEVANT MATERIALS
A1 INTRODUCTION
A2 BODY MATERIAL
A3 PLASTICS IN NON-LOAD-BEARING APPLICATIONS
A4 VISORS
A4.1 Visor material
A4.2 Self-cleaning glass coatings
A5 CONTROL GEAR
A5.1 General
A5.2 Magnetic ballasts
A5.3 Electronic control gear
A5.4 Lighting control systems for roads and public spaces
A5.5 Control gear location
A6 LAMPS
A6.1 General
A6.2 High xenon or super high pressure sodium vapour lamps
A6.3 Lampholders
A6.4 Solid state lighting (SSL)
APPENDIX B - LIST OF REFERENCED DOCUMENTS
APPENDIX C - INFORMATION RECOMMENDED TO BE SUPPLIED WITH ENQUIRY OR ORDER
APPENDIX D - POLE/BRACKET ARM END DETAIL FOR TOP-ENTRY LUMINAIRES
BIBLIOGRAPHY
SA/SNZ TS 1158.6:2015
Online Library subscription information
Online library subscriptions provide a cost-effective solution for organisations of any size to access the latest standards, offering 24/7 access to a personalised catalogue. The service ensures subscribers have have the most up-to-date version of selected standards, incluing automatic updates for any amendments or versions. Pricing is dependent on the chosen standards and the number of concurrent users, with discounts applied from the standards PDF price. For customised subscriptions or further inquiries, contact the Online Library team.