ISO 8029:2014
Plastics hose — General-purpose collapsible water hose, textile-reinforced — Specification
ISO 8029:2014 specifies the requirements for four types of textile-reinforced thermoplastics collapsible water hoses for general applications for use in the temperature range of −10 °C to 55 °C. Such hoses are classified into four types, as follows:
low pressure, designed for a maximum working pressure of up to 0,4 MPa (4,0 bar) at 23 °C and up to 0,2 MPa (2,0 bar) at 55 °C;
medium pressure, for a maximum working pressure of up to 0,7 MPa (7,0 bar) at 23 °C and up to 0,36 MPa (3,6 bar) at 55 °C;
high pressure, for a maximum working pressure of up to 1,0 MPa (10,0 bar) at 23 °C and up to 0,51 MPa (5,1 bar) at 55 °C;
extra-high pressure, for a maximum working pressure of up to 1,55 MPa (15,5 bar) at 23 °C and up to 0,79 MPa (7,9 bar) at 55 °C.
| Get this standard | Prices exclude GST | |
|---|---|---|
| PDF ( Single user document) |
$179.13 NZD
|
|
| HardCopy |
$214.78 NZD
|
|
| Networkable PDF |
Price varies
|
Section sec_1
Section sec_2
Section sec_3
Section sec_4
Section sec_5
Section sec_6
Section sec_7
Section sec_7.1
Table tab_1
Section sec_7.2
Section sec_8
Section sec_8.1
Table tab_2
Section sec_8.2
Section sec_8.2.1
Table tab_3
Table tab_4
Section sec_8.2.2
Table tab_5
Table tab_6
Section sec_8.2.3
Section sec_8.2.4
Section sec_8.2.5
Section sec_8.2.6
Section sec_9
Section sec_10
Section sec_11
Section sec_12
Annex sec_A
Annex sec_A.1
Annex sec_A.2
Annex sec_A.3
Table tab_a
Figure fig_A.1
Annex sec_B
Table tab_B.1
Annex sec_C
Table tab_C.1
Annex sec_D
Reference ref_1
Reference ref_2
Reference ref_3
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Classification
5 Couplings and end fittings
6 Materials and construction
7 Dimensions and tolerances
7.1 Inside diameter and tolerance
7.2 Tolerance on length
8 Physical properties
8.1 Plastic compounds
8.2 Performance requirements for finished hose
9 Frequency of testing
10 Test certificate/report
11 Marking
12 Recommendations for packaging and storage
Annex A (normative) Abrasion test
Annex B (normative) Type and routine testing
Annex C (informative) Production tests
Annex D (informative) Couplings and end fittings
Bibliography
Previous versions
Keep me up-to-date
Register to receive notifications when updates are made to this standard.
Related Information
Similar Standards
-
AS/NZS 1869:2012
Hose and hose assemblies for liquefied petroleum gases (LP Gas), natural gas and town gas -
BS 1103:1989
Specification for fabrics for the reinforcement of rubber hoses
-
BS 4089:1999
Specification for metallic hose assemblies for liquid petroleum gases and liquefied natural gases
-
BS 5122:1986
Specification for rubber hoses for low-pressure and medium-pressure saturated steam
Section sec_1
Section sec_2
Section sec_3
Section sec_4
Section sec_5
Section sec_6
Section sec_7
Section sec_7.1
Table tab_1
Section sec_7.2
Section sec_8
Section sec_8.1
Table tab_2
Section sec_8.2
Section sec_8.2.1
Table tab_3
Table tab_4
Section sec_8.2.2
Table tab_5
Table tab_6
Section sec_8.2.3
Section sec_8.2.4
Section sec_8.2.5
Section sec_8.2.6
Section sec_9
Section sec_10
Section sec_11
Section sec_12
Annex sec_A
Annex sec_A.1
Annex sec_A.2
Annex sec_A.3
Table tab_a
Figure fig_A.1
Annex sec_B
Table tab_B.1
Annex sec_C
Table tab_C.1
Annex sec_D
Reference ref_1
Reference ref_2
Reference ref_3
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Classification
5 Couplings and end fittings
6 Materials and construction
7 Dimensions and tolerances
7.1 Inside diameter and tolerance
7.2 Tolerance on length
8 Physical properties
8.1 Plastic compounds
8.2 Performance requirements for finished hose
9 Frequency of testing
10 Test certificate/report
11 Marking
12 Recommendations for packaging and storage
Annex A (normative) Abrasion test
Annex B (normative) Type and routine testing
Annex C (informative) Production tests
Annex D (informative) Couplings and end fittings
Bibliography