ISO 25239-5:2020
Friction stir welding — Aluminium — Part 5: Quality and inspection requirements
This document specifies a method for determining the capability of a manufacturer to use the friction stir welding (FSW) process for the production of products of the specified quality. It specifies quality requirements, but does not assign those requirements to any specific product group.
In this document, the term "aluminium" refers to aluminium and its alloys.
This document does not apply to friction stir spot welding which is covered by the ISO 18785 series.
| Get this standard | Prices exclude GST | |
|---|---|---|
| PDF ( Single user document) |
$118.26 NZD
|
|
| HardCopy |
$152.17 NZD
|
|
| Networkable PDF |
Price varies
|
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Quality requirements
4.1 General
4.2 Welding personnel
4.2.1 General
4.2.2 Welding operator
4.3 Inspection and testing personnel
4.3.1 General
4.3.2 Personnel performing non-destructive testing (including visual testing)
4.3.3 Destructive testing personnel
4.4 Equipment
4.4.1 Suitability of equipment
4.4.2 Reproducibility tests for qualified machine welding settings
4.4.3 Equipment maintenance
4.5 Welding procedure specification
4.6 Friction stir welding tool
4.6.1 Identification
4.6.2 Friction stir welding tool inspection
4.7 Pre-weld joint preparation and fit-up
4.7.1 Joint preparation
4.7.2 Pre-weld cleaning
4.8 Preheating and interpass temperature control
4.9 Tack welds
4.10 Welding
4.11 Postweld heat treatment
4.12 Inspection and testing
4.12.1 General
4.12.2 Inspection and testing before welding
4.12.3 Inspection and testing during welding
4.12.4 Inspection and testing after welding
4.12.5 Damaged and non-conforming welds
4.12.6 Weld geometry correction
4.13 Identification and traceability
Annex A (normative) Imperfections, testing and examination, acceptance levels, and ISO 6520-1 reference number
Bibliography
Previous versions
Keep me up-to-date
Register to receive notifications when updates are made to this standard.
Related Information
Similar Standards
-
AS/NZS 1554.1:2014
Structural steel welding - Part 1: Welding of steel structures -
AS/NZS 1554.1:2014 A1
Structural steel welding - Part 1: Welding of steel structures: Amendment 1 -
AS/NZS 1554.1:2014 A2
Structural steel welding - Part 1: Welding of steel structures: Amendment 2 -
AS/NZS 1554.2:2003
Structural steel welding - Stud welding (steel studs to steel)
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Quality requirements
4.1 General
4.2 Welding personnel
4.2.1 General
4.2.2 Welding operator
4.3 Inspection and testing personnel
4.3.1 General
4.3.2 Personnel performing non-destructive testing (including visual testing)
4.3.3 Destructive testing personnel
4.4 Equipment
4.4.1 Suitability of equipment
4.4.2 Reproducibility tests for qualified machine welding settings
4.4.3 Equipment maintenance
4.5 Welding procedure specification
4.6 Friction stir welding tool
4.6.1 Identification
4.6.2 Friction stir welding tool inspection
4.7 Pre-weld joint preparation and fit-up
4.7.1 Joint preparation
4.7.2 Pre-weld cleaning
4.8 Preheating and interpass temperature control
4.9 Tack welds
4.10 Welding
4.11 Postweld heat treatment
4.12 Inspection and testing
4.12.1 General
4.12.2 Inspection and testing before welding
4.12.3 Inspection and testing during welding
4.12.4 Inspection and testing after welding
4.12.5 Damaged and non-conforming welds
4.12.6 Weld geometry correction
4.13 Identification and traceability
Annex A (normative) Imperfections, testing and examination, acceptance levels, and ISO 6520-1 reference number
Bibliography