ISO 19085-3:2017
Woodworking machines — Safety requirements — Part 3: Numerically controlled (NC) boring and routing machines
ISO 19085-3:2017 gives the safety requirements and measures for numerically controlled (NC) boring machines, NC routing machines and NC combined boring/routing machines (as defined in 3.1), hereinafter referred to as "machines".
ISO 19085-3:2017 deals with all significant hazards, hazardous situations and events, listed in Clause 4, relevant to the machines when they are operated, adjusted and maintained as intended and under the conditions foreseen by the manufacturer including reasonably foreseeable misuse. Also, transport, assembly, dismantling, disabling and scrapping phases have been taken into account.
| Get this standard | Prices exclude GST | |
|---|---|---|
| PDF ( Single user document) |
$118.26 NZD
|
|
| HardCopy |
$152.17 NZD
|
|
| Networkable PDF |
Price varies
|
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 List of significant hazards
5 Safety requirements and measures for controls
5.1 Safety and reliability of control systems
5.2 Control devices
5.2.1 General
5.2.2 Hand-held control sets
5.3 Start
5.4 Safe stops
5.4.1 General
5.4.2 Normal stop
5.4.3 Operational stop
5.4.4 Emergency stop
5.5 Braking function of tool spindles
5.6 Mode selection
5.6.1 General
5.6.2 Machining mode [MODE 1]
5.6.3 Machine setting mode [MODE 2]
5.6.4 Clamping device manual positioning mode [MODE 3]
5.7 Spindle speed changing
5.7.1 Spindle speed changing by changing belts on the pulleys
5.7.2 Spindle speed changing by incremental speed change motor
5.7.3 Infinitely variable speed by frequency inverter
5.8 Failure of any power supply
5.9 Manual reset control
5.10 Enabling control
5.11 Machine moving parts speed monitoring
5.12 Time delay
5.13 Teleservice
6 Safety requirements and measures for protection against mechanical hazards
6.1 Stability
6.1.1 Stationary machines
6.1.2 Displaceable machines
6.2 Risk of break-up during operation
6.3 Tool holder and tool design
6.3.1 General
6.3.2 Spindle locking
6.3.3 Circular saw blade fixing device
6.3.4 Flange dimension for circular saw blades
6.4 Braking
6.4.1 Braking of tool spindle
6.4.2 Maximum run-down time
6.4.3 Brake release
6.5 Safeguards
6.5.1 Fixed guards
6.5.2 Interlocking moveable guards
6.5.3 Hold-to-run control
6.5.4 Two-hand control
6.5.5 Electro-sensitive protective equipment (ESPE)
6.5.6 Pressure-sensitive protective equipment (PSPE)
6.6 Prevention of access to moving parts
6.6.1 General
6.6.2 Guarding of tools
6.6.3 Guarding of drives
6.6.4 Guarding of shearing and/or crushing zones
6.7 Impact hazard
6.8 Clamping device
6.9 Measures against ejection
6.9.1 General
6.9.2 Guards materials and characteristics
6.10 Workpiece support and guides
7 Safety requirements and measures for protection against other hazards
7.1 Fire
7.2 Noise
7.2.1 Noise reduction at the design stage
7.2.2 Noise emission measurement
7.3 Emission of chips and dust
7.4 Electricity
7.4.1 General
7.4.2 Displaceable machines
7.5 Ergonomics and handling
7.6 Lighting
7.7 Pneumatics
7.8 Hydraulics
7.9 Electromagnetic compatibility
7.10 Laser
7.11 Static electricity
7.12 Errors of fitting
7.13 Isolation
7.14 Maintenance
8 Information for use
8.1 Warning devices
8.2 Marking
8.2.1 General
8.2.2 Additional markings
8.3 Instruction handbook
8.3.1 General
8.3.2 Additional information
Annex A (informative) Performance levels required
Annex B (normative) Test for braking function
Annex C (normative) Stability test for displaceable machines
Annex D (normative) Impact test for guards
Annex E (normative) Noise emission measurement for machines not in ISO 7960
Annex F (normative) Impact test for curtains
Annex G (normative) Wear test for curtains
Annex H (normative) Dynamic test for pressure-sensitive bumpers, edges, trip bars, trip plates
Annex ZA (informative) Relationship between this European Standard and the Essential Requirements of EU Directive 2006/42/EC
Bibliography
Keep me up-to-date
Register to receive notifications when updates are made to this standard.
Related Information
Similar Standards
-
AS/NZS 3000:2018
Electrical installations - Known as the Australian/New Zealand Wiring Rules -
AS/NZS 3000:2018 A1
Electrical installations (known as the Australian/New Zealand Wiring Rules): Amendment 1 -
AS/NZS 3000:2018 A2
Electrical Installations (known as the Australian/New Zealand Wiring Rules)
-
AS/NZS 3000:2018 A3
Electrical installations (known as the Australian/New Zealand Wiring Rules)
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 List of significant hazards
5 Safety requirements and measures for controls
5.1 Safety and reliability of control systems
5.2 Control devices
5.2.1 General
5.2.2 Hand-held control sets
5.3 Start
5.4 Safe stops
5.4.1 General
5.4.2 Normal stop
5.4.3 Operational stop
5.4.4 Emergency stop
5.5 Braking function of tool spindles
5.6 Mode selection
5.6.1 General
5.6.2 Machining mode [MODE 1]
5.6.3 Machine setting mode [MODE 2]
5.6.4 Clamping device manual positioning mode [MODE 3]
5.7 Spindle speed changing
5.7.1 Spindle speed changing by changing belts on the pulleys
5.7.2 Spindle speed changing by incremental speed change motor
5.7.3 Infinitely variable speed by frequency inverter
5.8 Failure of any power supply
5.9 Manual reset control
5.10 Enabling control
5.11 Machine moving parts speed monitoring
5.12 Time delay
5.13 Teleservice
6 Safety requirements and measures for protection against mechanical hazards
6.1 Stability
6.1.1 Stationary machines
6.1.2 Displaceable machines
6.2 Risk of break-up during operation
6.3 Tool holder and tool design
6.3.1 General
6.3.2 Spindle locking
6.3.3 Circular saw blade fixing device
6.3.4 Flange dimension for circular saw blades
6.4 Braking
6.4.1 Braking of tool spindle
6.4.2 Maximum run-down time
6.4.3 Brake release
6.5 Safeguards
6.5.1 Fixed guards
6.5.2 Interlocking moveable guards
6.5.3 Hold-to-run control
6.5.4 Two-hand control
6.5.5 Electro-sensitive protective equipment (ESPE)
6.5.6 Pressure-sensitive protective equipment (PSPE)
6.6 Prevention of access to moving parts
6.6.1 General
6.6.2 Guarding of tools
6.6.3 Guarding of drives
6.6.4 Guarding of shearing and/or crushing zones
6.7 Impact hazard
6.8 Clamping device
6.9 Measures against ejection
6.9.1 General
6.9.2 Guards materials and characteristics
6.10 Workpiece support and guides
7 Safety requirements and measures for protection against other hazards
7.1 Fire
7.2 Noise
7.2.1 Noise reduction at the design stage
7.2.2 Noise emission measurement
7.3 Emission of chips and dust
7.4 Electricity
7.4.1 General
7.4.2 Displaceable machines
7.5 Ergonomics and handling
7.6 Lighting
7.7 Pneumatics
7.8 Hydraulics
7.9 Electromagnetic compatibility
7.10 Laser
7.11 Static electricity
7.12 Errors of fitting
7.13 Isolation
7.14 Maintenance
8 Information for use
8.1 Warning devices
8.2 Marking
8.2.1 General
8.2.2 Additional markings
8.3 Instruction handbook
8.3.1 General
8.3.2 Additional information
Annex A (informative) Performance levels required
Annex B (normative) Test for braking function
Annex C (normative) Stability test for displaceable machines
Annex D (normative) Impact test for guards
Annex E (normative) Noise emission measurement for machines not in ISO 7960
Annex F (normative) Impact test for curtains
Annex G (normative) Wear test for curtains
Annex H (normative) Dynamic test for pressure-sensitive bumpers, edges, trip bars, trip plates
Annex ZA (informative) Relationship between this European Standard and the Essential Requirements of EU Directive 2006/42/EC
Bibliography