British publications

You can now purchase PDFs of British standards from Standards New Zealand – please call 0800 782 632 during business hours or email enquiries@standards.co.nz to order PDFs. British standard publications in hardcopy format are also available for purchase from our web site www.standards.co.nz by entering the standard number.

British standards

The publications listed below are new and revised British standards that were made available last month. An existing BSI publication bearing a number identical to one announced below is automatically withdrawn unless stated otherwise. In all other cases of supersession, details are given and a corresponding entry appears in the ’British standards withdrawn’ section.

  • BS 6349-1-1:2013 Maritime works. General. Code of practice for planning and design for operations

Together with BS 6349-1-2, BS 6349-1-3:2012 and BS 6349-1-4:2013, this part of BS 6349 supersedes BS 6349-1:2000, which will be withdrawn when all four of the new subparts have been published

  • BS 6867:2013 Maintenance of electrical switchgear and controlgear for voltages above 36 kV. Code of practice

Supersedes BS 6867:1987

  • BS 7121-2-9:2013 Code of practice for the safe use of cranes. Inspection, maintenance and thorough examination. Cargo handling and container cranes
  • BS 7985:2013 Code of practice for the use of rope access methods for industrial purposes. Recommendations and guidance supplementary to BS ISO 22846

Supersedes BS 7985:2009

  • BS 8000-6:2013 Workmanship on building sites. Code of practice for slating and tiling of roofs and walls

Supersedes BS 8000-6:1990

  • BS 8103-2:2013 Structural design of low-rise buildings. Code of practice for masonry walls for housing

Supersedes BS 8103-2:2005

  • BS 8544:2013 Guide for life cycle costing of maintenance during the in use phases of buildings
  • BS 8595:2013 Code of practice for the selection of water reuse systems
  • BS 102000:2013 Code of practice for the provision of investigative services
BS EN standards

The following are British standard implementations of the English language versions of European standards (ENs). The date referenced in the identifier is the date of the European standard.  You can now purchase PDFs of British standards from Standards New Zealand – please email enquiries@standards.co.nz or call 0800 782 632 during business hours to order PDFs.

  • BS EN 81-82:2013 Safety rules for the construction and installation of lifts. Existing lifts. Rules for the improvement of the accessibility of existing lifts for persons including persons with disability

Supersedes DD CEN/TS 81-82:2008

  • BS EN 336:2013 Structural timber. Sizes, permitted deviations

Supersedes BS EN 336:2003

  • BS EN 485-2:2013 Aluminium and aluminium alloys. Sheet, strip and plate. Mechanical properties

Supersedes BS EN 485-2:2008

  • BS EN 590:2013 Automotive fuels. Diesel. Requirements and test methods

Supersedes BS EN 590:2009+A1:2010

  • BS EN 754-2:2013 Aluminium and aluminium alloys. Cold drawn rod/bar and tube. Mechanical properties

Supersedes BS EN 754-2:2008

  • BS EN 755-2:2013 Aluminium and aluminium alloys. Extruded rod/bar, tube and profiles. Mechanical properties

Supersedes BS EN 755-2:2008

  • BS EN 1594:2013 Gas infrastructure. Pipelines for maximum operating pressure over 16 bar. Functional requirements

Supersedes BS EN 1594:2009

  • BS EN 1790:2013 Road marking materials. Preformed road markings

Supersedes BS EN 1790:1998

  • BS EN 1866-3:2013 Mobile fire extinguishers. Requirements for the assembly, construction and pressure resistance of CO2 extinguishers which comply with the requirements of EN 1866-1

Supersedes BS EN 1866:2005 which remains current

  • BS EN 1953:2013 Atomising and spraying equipment for coating materials. Safety requirements

Supersedes BS EN 1953:1998+A1:2009

  • BS EN 2565:2013 Aerospace series. Preparation of carbon fibre reinforced resin panels for test purposes
  • BS EN 3682-001:2013 Aerospace series. Connectors, plug and receptacle, electrical, rectangular, interchangeable insert type, rack to panel, operating temperature 150ºC continuous. Technical specification

Supersedes BS EN 3682-001:2006

  • BS EN 3682-002:2013 Aerospace series. Connectors, plug and receptacle, electrical, rectangular, interchangeable insert type, rack to panel, operating temperature 150ºC continuous. Specification of performance and contact arrangements

Supersedes BS EN 3682-002:2006

  • BS EN ISO 3807:2013 Gas cylinders. Acetylene cylinders. Basic requirements and type testing
  • BS EN 3983:2013 Aerospace series. Aluminium alloy AL-P7050-. T7651. Plate. 6 mm < a ≤ 160 mm
  • BS EN 4681-001:2012 Aerospace series. Cables, electric, general purpose, with conductors in aluminium or copper-clad aluminium. Technical specification
  • BS EN ISO 4892-3:2013 Plastics. Methods of exposure to laboratory light sources. Fluorescent UV lamps

Supersedes BS EN ISO 4892-3:2006

  • BS EN ISO 5395-1:2013 Garden equipment. Safety requirements for combustion-engine-powered lawnmowers. Terminology and common tests

Together with BS EN ISO 5395-2:2013 and BS EN ISO 5395-3:2013 it supersedes BS EN 836:1997+A4:2011, which is withdrawn

  • BS EN ISO 5395-2:2013 Garden equipment. Safety requirements for combustion-engine-powered lawnmowers. Pedestrian-controlled lawnmowers

Together with BS EN ISO 5395-1:2013 and BS EN ISO 5395-3:2013 it supersedes BS EN 836:1997+A4:2011, which is withdrawn

  • BS EN ISO 5395-3:2013 Garden equipment. Safety requirements for combustion-engine-powered lawnmowers. Ride-on lawnmowers with seated operator

Together with BS EN ISO 5395-1:2013 and BS EN ISO 5395-2:2013 it supersedes BS EN 836:1997+A4:2011, which is withdrawn

  • BS EN ISO 5999:2013 Flexible cellular polymeric materials. Polyurethane foam for load-bearing applications excluding carpet underlay. Specification

Supersedes BS EN ISO 5999:2007

  • BS EN ISO 8980-3:2013 Ophthalmic optics. Uncut finished spectacle lenses. Transmittance specifications and test methods

Supersedes BS EN ISO 8980-3:2004

  • BS EN ISO 9692-1:2013 Welding and allied processes. Types of joint preparation. Manual metal arc welding, gas-shielded metal arc welding, gas welding, TIG welding and beam welding of steels

Supersedes BS EN ISO 9692-1:2003

  • BS EN 10149-1:2013 Hot rolled flat products made of high yield strength steels for cold forming. General technical delivery conditions

Supersedes BS EN 10149-1:1996

  • BS EN 10149-2:2013 Hot rolled flat products made of high yield strength steels for cold forming. Technical delivery conditions for thermomechanically rolled steels

Supersedes BS EN 10149-2:1996

  • BS EN 10149-3:2013 Hot rolled flat products made of high yield strength steels for cold forming. Technical delivery conditions for normalized or normalized rolled steels

Supersedes BS EN 10149-3:1996

  • BS EN ISO 12209:2013 Gas cylinders. Outlet connections for gas cylinder valves for compressed breathable air

Supersedes BS EN ISO 12209-1:2001, BS EN ISO 12209-2:2001 and BS EN ISO 12209-3:2001

  • BS EN 12228:2013 Surfaces for sports areas. Determination of joint strength of synthetic surfaces

Supersedes BS EN 12228:2002

  • BS EN 12234:2013 Surfaces for sports areas. Determination of ball roll behaviour

Supersedes BS EN 12234:2002

  • BS EN 12235:2013 Surfaces for sports areas. Determination of vertical ball behaviour

Supersedes BS EN 12235:2004

  • BS EN ISO 12311:2013 Personal protective equipment. Test methods for sunglasses and related eyewear

Together with BS EN ISO 12312-1:2013, it supersedes BS EN 1836:2005 which is withdrawn

  • BS EN ISO 12312-1:2013 Eye and face protection. Sunglasses and related eyewear. Sunglasses for general use

Together with BS EN ISO 12311:2013, it supersedes BS EN 1836:2005 which is withdrawn

  • BS EN 12560-2:2013 Flanges and their joints. Dimensions of gaskets for Class-designated flanges. Spiral wound gaskets for use with steel flanges

Supersedes BS EN 12560-2:2001

  • BS EN 12616:2013 Surfaces for sports areas. Determination of water infiltration rate

Supersedes BS EN 12616:2003

  • BS EN 12871:2013 Wood-based panels. Determination of performance characteristics for load bearing panels for use in floors, roofs and walls

Supersedes BS EN 12871:2010

  • BS EN 13195:2013 Aluminium and aluminium alloys. Specifications for wrought and cast products for marine applications (shipbuilding, marine and offshore)

Supersedes BS EN 13195:2009

  • BS EN 13438:2013 Paints and varnishes. Powder organic coatings for hot dip galvanised or sherardised steel products for construction purposes

Supersedes BS EN 13438:2005

  • BS EN 13547:2013 Industrial valves. Copper alloy ball valves

Supersedes DD CEN/TS 13547:2006

  • BS EN 13624:2013 Chemical disinfectants and antiseptics. Quantitative suspension test for the evaluation of fungicidal or yeasticidal activity in the medical area. Test method and requirements (phase 2, step 1)

Supersedes BS EN 13624:2003

  • BS EN 13707:2013 Flexible sheets for waterproofing. Reinforced bitumen sheets for roof waterproofing. Definitions and characteristics

Supersedes BS EN 13707:2004+A2:2009

  • BS EN 13808:2013 Bitumen and bituminous binders. Framework for specifying cationic bituminous emulsions

Supersedes BS EN 13808:2005 which is withdrawn. Together with BS EN 15322:2013, it also supersedes BS EN 14733:2005+A1:2010, which is withdrawn

  • BS EN ISO 14113:2013 Gas welding equipment. Rubber and plastics hose and hose assemblies for use with industrial gases up to 450 bar (45 MPa)

Supersedes BS EN ISO 14113:2008

  • BS EN ISO 14119:2013 Safety of machinery. Interlocking devices associated with guards. Principles for design and selection
  • BS EN ISO 14253-1:2013 Geometrical product specifications (GPS). Inspection by measurement of workpieces and measuring equipment. Decision rules for proving conformity or nonconformity with specification

Supersedes BS EN ISO 14253-1:1999

  • BS EN 14511-1:2013 Air conditioners, liquid chilling packages and heat pumps with electrically driven compressors for space heating and cooling. Terms, definitions and classification

Supersedes BS EN 14511-1:2011

  • BS EN ISO 14581:2013 Fasteners. Hexalobular socket countersunk flat head screws
  • BS EN ISO 14582:2013 Fasteners. Hexalobular socket countersunk head screws, high head
  • BS EN 14825:2013 Air conditioners, liquid chilling packages and heat pumps, with electrically driven compressors, for space heating and cooling. Testing and rating at part load conditions and calculation of seasonal performance

Supersedes BS EN 14825:2012

  • BS EN 14877:2013 Synthetic surfaces for outdoor sports areas. Specification

Supersedes BS EN 14877:2006

  • BS EN ISO 14889:2013 Ophthalmic optics. Spectacle lenses. Fundamental requirements for uncut finished lenses

Supersedes BS EN ISO 14889:2009

  • BS EN 14960:2013 Inflatable play equipment. Safety requirements and test methods

Supersedes BS EN 14960:2006

  • BS EN 15101-1:2013 Thermal insulation products for buildings. Insitu formed loose fill cellulose (LFCI) products. Specification for the products before installation
  • BS EN 15101-2:2013 Thermal insulation products for buildings. Insitu formed loose fill cellulose (LFCI) products. Specification for the installed products
  • BS EN 15330-1:2013 Surfaces for sports areas. Synthetic turf and needle-punched surfaces primarily designed for outdoor use. Specification for synthetic turf surfaces for football, hockey, rugby union training, tennis and multi-sports use

Supersedes BS EN 15330-1:2007

  • BS EN ISO 15528:2013 Paints, varnishes and raw materials for paints and varnishes. Sampling

Supersedes BS EN ISO 15528:2000

  • BS EN ISO 15798:2013 Ophthalmic implants. Ophthalmic viscosurgical devices

Supersedes BS EN ISO 15798:2010

  • BS EN 16116-1:2013 Railway applications. Design requirements for steps, handrails and associated access for staff. Passenger vehicles, luggage vans and locomotives
  • BS EN 16116-2:2013 Railway applications. Design requirements for steps, handrails and associated access for staff. Freight wagons
  • BS EN 16121:2013 Non-domestic storage furniture. Requirements for safety, strength, durability and stability
  • BS EN 16317:2013 Fertilizers. Determination of trace elements. Determination of arsenic by inductively coupled plasma-atomic emission spectrometry (ICP-AES) after aqua regia dissolution

Supersedes PD CEN/TS 16317:2012

  • BS EN 16320:2013 Fertilizers. Determination of trace elements. Determination of mercury by vapour generation (VG) after aqua regia dissolution

Supersedes PD CEN/TS 16320:2012

  • BS EN 16321-1:2013 Petrol vapour recovery during refuelling of motor vehicles at service stations. Test methods for the type approval efficiency assessment of petrol vapour recovery systems
  • BS EN 16321-2:2013 Petrol vapour recovery during refuelling of motor vehicles at service stations. Test methods for verification of vapour recovery systems at service stations
  • BS EN 16322:2013 Conservation of Cultural Heritage. Test methods. Determination of drying properties
  • BS EN 16377:2013 Characterization of waste. Determination of brominated flame retardants (BFR) in solid waste
  • BS EN 16416:2013 Geosynthetic clay barriers. Determination of water flux index. Flexible wall permeameter method at constant head
  • BS EN ISO 20957-1:2013 Stationary training equipment. General safety requirements and test methods

Supersedes BS EN 957-1:2005

  • BS EN ISO 28888:2013 Dentistry. Screening method for erosion potential of oral rinses on dental hard tissues
  • BS EN 50131-2-7-1:2012 Alarm systems. Intrusion and hold-up systems. Intrusion detectors. Glass break detectors (acoustic)

Supersedes DD CLC/TS 50131-2-7-1:2009

  • BS EN 50131-2-7-2:2012 Alarm systems. Intrusion and hold-up systems. Intrusion detectors. Glass break detectors (passive)

Supersedes DD CLC/TS 50131-2-7-2:2009

  • BS EN 50131-2-7-3:2012 Alarm systems. Intrusion and hold-up systems. Intrusion detectors. Glass break detectors (active)

Supersedes DD CLC/TS 50131-2-7-3:2009

  • BS EN 50136-3:2013 Alarm systems. Alarm transmission systems and equipment. Requirements for Receiving Centre Transceiver (RCT)
  • BS EN 50193-1:2013 Electric instantaneous water heaters. General requirements

Supersedes BS EN 50193:1997 which remains current

  • BS EN 50288-2-1:2013 Multi-element metallic cables used in analogue and digital communication and control. Sectional specification for screened cables characterised up to 100 MHz. Horizontal and building backbone cables

Supersedes BS EN 50288-2-1:2003

  • BS EN 50288-2-2:2013 Multi-element metallic cables used in analogue and digital communication and control. Sectional specification for screened cables characterised up to 100 MHz. Work area and patch cord cables

Supersedes BS EN 50288-2-2:2003

  • BS EN 50288-3-1:2013 Multi-element metallic cables used in analogue and digital communication and control. Sectional specification for unscreened cables characterised up to 100 MHz. Horizontal and building backbone cables

Supersedes BS EN 50288-3-1:2003

  • BS EN 50288-3-2:2013 Multi-element metallic cables used in analogue and digital communication and control. Sectional specification for unscreened cables characterised up to 100 MHz. Work area and patch cord cables

Supersedes BS EN 50288-3-2:2003

  • BS EN 50288-4-1:2013 Multi-element metallic cables used in analogue and digital communication and control. Sectional specification for screened cables characterised up to 600 MHz. Horizontal and building backbone cables

Supersedes BS EN 50288-4-1:2003

  • BS EN 50355:2013 Railway applications. Railway rolling stock cables having special fire performance. Guide to use

Supersedes BS EN 50355:2003 which remains current

  • BS EN 55015:2013 Limits and methods of measurement of radio disturbance characteristics of electrical lighting and similar equipment

Supersedes BS EN 55015:2006+A2:2009 which remains current

  • BS EN 60312-1:2013 Vacuum cleaners for household use. Dry vacuum cleaners. Methods for measuring the performance

Together with BS EN 60312-2 it supersedes BS EN 60312:2008, which will be fully withdrawn on a date to be announced upon publication of BS EN 60312-2

  • BS EN 60384-14:2013 Fixed capacitors for use in electronic equipment. Sectional specification: Fixed capacitors for electromagnetic interference suppression and connection to the supply mains

Supersedes BS EN 60384-14:2005

  • BS EN 60519-4:2013 Safety in electroheating installations. Particular requirements for arc furnace installations

Supersedes BS EN 60519-4:2006

  • BS EN 60544-1:2013 Electrical insulating materials. Determination of the effects of ionizing radiation. Radiation interaction and dosimetry

Supersedes BS EN 60544-1:1995

  • BS EN 60695-9-1:2013 Fire hazard testing. Surface spread of flame. General guidance

Supersedes BS EN 60695-9-1:2005

  • BS EN 60695-11-10:2013 Fire hazard testing. Test flames. 50 W horizontal and vertical flame test methods

Supersedes BS EN 60695-11-10:1999

  • BS EN 60747-16-5:2013 Semiconductor devices. Microwave integrated circuits. Oscillators
  • BS EN 61169-42:2013 Radio-frequency connectors. Sectional specification for CQN series quick lock RF coaxial connectors
  • BS EN 61191-1:2013 Printed board assemblies. Generic specification. Requirements for soldered electrical and electronic assemblies using surface mount and related assembly technologies

Supersedes BS EN 61191-1:1999

  • BS EN 61280-1-1:2013 Fibre optic communication subsystem basic test procedures. Test procedures for general communication subsystems. Transmitter output optical power measurement for single-mode optical fibre cable

Supersedes BS EN 61280-1-1:1998

  • BS EN 61300-2-44:2013 Fibre optic interconnecting devices and passive components. Basic test and measurement procedures. Tests. Flexing of the strain relief of fibre optic devices

Supersedes BS EN 61300-2-44:2008

  • BS EN 61300-3-48:2013 Fibre optic interconnect devices and passive components. Basic test and measurement procedures. Examinations and measurements. Spring compression force of the coupling sleeve for rectangular ferrule multi-fibre connectors
  • BS EN 61643-311:2013 Components for low-voltage surge protective devices. Performance requirements and test circuits for gas discharge tubes (GDT)

Together with BS EN 61643-312:2013 it supersedes BS EN 61643-311:2001 which remains current

  • BS EN 61643-312:2013 Components for low-voltage surge protective devices. Selection and application principles for gas discharge tubes

Together with BS EN 61643-311:2013 it supersedes BS EN 61643-311:2001 which remains current

  • BS EN 61710:2013 Power law model. Goodness-of-fit tests and estimation methods

Supersedes BS IEC 61710:2000

  • BS EN 61788-5:2013 Superconductivity. Matrix to superconductor volume ratio measurement. Copper to superconductor volume ratio of Cu/Nb-Ti composite superconducting wires

Supersedes BS EN 61788-5:2001

  • BS EN 61938:2013 Multimedia systems. Guide to the recommended characteristics of analogue interfaces to achieve interoperability

Supersedes BS EN 61938:1997

  • BS EN 62040-4:2013 Uninterruptible power systems (UPS). Environmental aspects. Requirements and reporting
  • BS EN 62047-11:2013 Semiconductor devices. Micro-electromechanical devices. Test method for coefficients of linear thermal expansion of free-standing materials for micro-electromechanical systems
  • BS EN 62047-18:2013 Semiconductor devices. Micro-electromechanical devices. Bend testing methods of thin film materials
  • BS EN 62047-19:2013 Semiconductor devices. Micro-electromechanical devices. Electronic compasses
  • BS EN 62056-6-1:2013 Electricity metering data exchange. The DLMS/COSEM suite. Object Identification System (OBIS)

Supersedes BS EN 62056-61:2007

  • BS EN 62056-6-2:2013 Electricity metering data exchange. The DLMS/COSEM suite. COSEM interface classes

Supersedes BS EN 62056-62:2007

  • BS EN 62056-7-6:2013 Electricity metering data exchange. The DLMS/COSEM suite. The 3-layer, connectionoriented HDLC based communication profile

Partially supersedes BS EN 62056-53:2007

  • BS EN 62056-8-3:2013 Electricity metering data exchange. The DLMS/COSEM suite. Communication profile for PLC S-FSK neighbourhood networks
  • BS EN 62068:2013 Electrical insulating materials and systems. General method of evaluation of electrical endurance under repetitive voltage impulses

Supersedes BS EN 62068-1:2003

  • BS EN 62133:2013 Secondary cells and batteries containing alkaline or other non-acid electrolytes. Safety requirements for portable sealed secondary cells, and for batteries made from them, for use in portable applications

Supersedes BS EN 62133:2003

  • BS EN 62264-1:2013 Enterprise-control system integration. Models and terminology

Supersedes BS EN 62264-1:2008

  • BS EN 62282-3-201:2013 Fuel cell technologies. Stationary fuel cell power systems. Performance test methods for small fuel cell power systems
  • BS EN 62321-1:2013 Determination of certain substances in electrotechnical products. Introduction and overview

Together with BS EN 62321-2:2013, BS EN 62321-3-1:2013, BS EN 62321-3-2:2013, BS EN 62321-4:2013, BS EN 62321-5:2013, BS EN 62321-6, BS EN 62321-7-1, BS EN 62321-7-2 and BS EN 62321-8 it supersedes BS EN 62321:2009, which will be withdrawn upon publication of all parts of the BS EN 62321 series

  • BS EN 62341-5-2:2013 Organic light emitting diode (OLED) displays. Mechanical endurance testing methods
  • BS EN 62343:2013 Dynamic modules. General and guidance
  • BS EN 62364:2013 Hydraulic machines. Guide for dealing with hydro-abrasive erosion in Kaplan, Francis, and Pelton turbines
  • BS EN 62496-2-4:2013 Optical circuit boards. Basic test and measurement procedures. Optical transmission test for optical circuit boards without input/output fibres
  • BS EN 62506:2013 Methods for product accelerated testing
  • BS EN 62542:2013 Environmental standardization for electrical and electronic products and systems. Glossary of terms
  • BS EN 62612:2013 Self-ballasted LED lamps for general lighting services with supply voltages >50 V. Performance requirements

Supersedes DD IEC/PAS 62612:2009

  • BS EN 62629-1-2:2013 3D Display devices. Generic. Terminology and letter symbols
  • BS EN 62680-3:2013 Universal serial bus interfaces for data and power. USB battery charging specification Revision 1.2
  • BS EN 62693:2013 Industrial electroheating installations. Test methods for infrared electroheating installations
  • BS EN 62716:2013 Photovoltaic (PV) modules. Ammonia corrosion testing
  • BS EN 62739-1:2013 Test method for erosion of wave soldering equipment using molten lead-free solder alloy. Erosion test method for metal materials without surface processing
BS ENs implemented by amendment
  • BS EN ISO 10579:2013 Geometrical product specifications (GPS). Dimensioning and tolerancing. Non-rigid parts TDW/4

Implementation of European Standard EN ISO 10579 by amendment to BS ISO 10579:2010

  • PD CEN ISO/TR 9241-331:2013 Ergonomics of human-system interaction. Optical characteristics of autostereoscopic displays

Implementation of European Standard CEN ISO/TR 9241-331 by amendment to PD ISO/TR 9241-331:2012

  • PD CEN ISO/TR 12296:2013 Ergonomics. Manual handling of people in the healthcare sector

Implementation of European Standard CEN ISO/TR 12296 by amendment to PD ISO/TR 12296:2012

  • PD CEN ISO/TR 24475:2013 Cosmetics. Good Manufacturing Practices. General training document

Implementation of European Standard CEN ISO/TR 24475 by amendment to PD ISO/TR 24475:2010

BS implementations

BS Implementations comprise the ISO or IEC text without any national deviation and with front and back cover indicating the UK committee responsible. No other information will normally be added. The date referenced in the identifier is the date of the international standard.

  • BS ISO 965-1:2013 ISO general purpose metric screw threads. Tolerances. Principles and basic data

Supersedes BS ISO 965-1:1998

  • BS ISO 1328-1:2013 Cylindrical gears. ISO system of flank tolerance classification. Definitions and allowable values of deviations relevant to flanks of gear teeth
  • BS ISO 2789:2013 Information and documentation. International library statistics

Supersedes BS ISO 2789:2006

  • BS ISO 4548-13:2013 Methods of test for full-flow lubricating oil filters for internal combustion engines. Static burst pressure test for composite filter housings
  • BS ISO 5433:2013 Leather. Bovine wet blue. Specification

Supersedes BS ISO 5433:1999

  • BS ISO 5721-1:2013 Agricultural tractors. Requirements, test procedures and acceptance criteria for the operator’s field of vision. Field of vision to the front

Together with BS ISO 5721-2, it supersedes BS ISO 5721:1989, which will be withdrawn upon publication of BS ISO 5721-2

  • BS ISO 6262-1:2013 End mills with indexable inserts. End mills with flatted cylindrical shank

Supersedes BS 4193-9:1982

  • BS ISO 6262-2:2013 End mills with indexable inserts. End mills with Morse taper shank

Supersedes BS 4193-10:1982

  • BS ISO 6621-5:2013 Internal combustion engines. Piston rings. Quality requirements

Supersedes BS ISO 6621-5:2005

  • BS ISO 6986:2013 Side and face milling (slotting) cutters with indexable inserts. Dimensions

Supersedes BS 4193-12:1984

  • BS ISO 8255-2:2013 Microscopes. Cover glasses. Quality of materials, standards of finish and mode of packaging

Supersedes BS 7011-3.2:1998

  • BS ISO 8405:2013 Tools for moulding. Ejector sleeves with cylindrical head. Basic series for general purposes

Supersedes BS ISO 8405:1998

  • BS ISO/IEC 9541-1:2012 Information technology. Font information interchange. Architecture

Supersedes BS ISO/IEC 9541-1:1991+A4:2009

  • BS ISO/IEC 9541-2:2012 Information technology. Font information interchange. Interchange format

Supersedes BS ISO/IEC 9541-2:1991+A2:2009

  • BS ISO/IEC 9541-3:2013 Information technology. Font information interchange. Glyph shape representation

Supersedes BS ISO/IEC 9541-3:1994+A2:2009

  • BS ISO 9912-3:2013 Agricultural irrigation equipment. Filters for micro-irrigation. Automatic flushing strainer type filters and disc filters
  • BS ISO 10362-2:2013 Cigarettes. Determination of water in smoke condensates. Karl Fischer method

Supersedes BS ISO 10362-2:1994+A1:2011

  • BS ISO 10631:2013 Metallic butterfly valves for general purposes
  • BS ISO 11783-14:2013 Tractors and machinery for agriculture and forestry. Serial control and communications data network. Sequence control
  • BS ISO 11916-1:2013 Soil quality. Determination of selected explosives and related compounds. Method using high-performance liquid chromatography (HPLC) with ultraviolet detection
  • BS ISO 11916-2:2013 Soil quality. Determination of selected explosives and related compounds. Method using gas chromatography (GC) with electron capture detection (ECD) or mass spectrometric detection (MS)
  • BS ISO 12130-2:2013 Plain bearings. Hydrodynamic plain tilting pad thrust bearings under steady-state conditions. Functions for calculation of tilting pad thrust bearings
  • BS ISO 12243:2003+A1:2012 Medical gloves made from natural rubber latex. Determination of water-extractable protein using the modified Lowry method
  • BS ISO 12749-2:2013 Nuclear energy, nuclear technologies, and radiological protection. Vocabulary. Radiological protection
  • BS ISO 13007-4:2013 Ceramic tiles. Grouts and adhesives. Test methods for grouts

Supersedes BS ISO 13007-4:2010

  • BS ISO 13163:2013 Water quality. Lead-210. Test method using liquid scintillation counting
  • BS ISO 13164-1:2013 Water quality. Radon-222. General principles
  • BS ISO 13164-2:2013 Water quality. Radon-222. Test method using gamma-ray spectrometry
  • BS ISO 13164-3:2013 Water quality. Radon-222. Test method using emanometry
  • BS ISO 13424:2013 Surface chemical analysis. X-ray photoelectron spectroscopy. Reporting of results of thin-film analysis
  • BS ISO 14222:2013 Space environment (natural and artificial). Earth upper atmosphere
  • BS ISO 15619:2013 Reciprocating internal combustion engines. Measurement method for exhaust silencers. Sound power level of exhaust noise and insertion loss using sound pressure and power loss ratio
  • BS ISO 15740:2013 Photography. Electronic still picture imaging. Picture transfer protocol (PTP) for digital still photography devices

Supersedes BS ISO 15740:2008

  • BS ISO 16087:2013 Implants for surgery. Roentgen stereophotogrammetric analysis for the assessment of migration of orthopaedic implants
  • BS ISO 16117:2013 Nuclear criticality safety. Estimation of the number of fissions of a postulated criticality accident
  • BS ISO 16343:2013 Energy performance of buildings. Methods for expressing energy performance and for energy certification of buildings
  • BS ISO 16346:2013 Energy performance of buildings. Assessment of overall energy performance
  • BS ISO 17091:2013 Workplace air. Determination of lithium hydroxide, sodium hydroxide, potassium hydroxide and calcium dihydroxide. Method by measurement of corresponding cations by suppressed ion chromatography
  • BS ISO 17992:2013 Iron ores. Determination of arsenic content. Hydride generation atomic absorption spectrometric method
  • BS ISO 18589-7:2013 Measurement of radioactivity in the environment. Soil. In situ measurement of gamma-emitting radionuclides
  • BS ISO 20773:2013 Cigarettes. Determination of nicotine-free dry particulate matter and nicotine in sidestream smoke. Method using a routine analytical linear smoking machine equipped with a fishtail chimney

Supersedes BS ISO 20773:2007

  • BS ISO 21485:2013 Textile machinery. Draw frame for cotton spinning. Vocabulary and principles of construction

Supersedes BS ISO 21485:2006

  • BS ISO 22514-2:2013 Statistical methods in process management. Capability and performance. Process capability and performance of time-dependent process models

Supersedes BS ISO 21747:2006

  • BS ISO 22889:2013 Metallic materials. Method of test for the determination of resistance to stable crack extension using specimens of low constraint

Supersedes BS ISO 22889:2007

  • BS ISO 23273:2013Fuel cell road vehicles. Safety specifications.  Protection against hydrogen hazards for vehicles fuelled with compressed hydrogen

Supersedes BS ISO 23273-2:2006

  • BS ISO 23380:2013 Selection of methods for the determination of trace elements in coal

Supersedes BS ISO 23380:2008

  • BS ISO/IEC 27001:2013 Information technology. Security techniques. Information security management systems. Requirements

Supersedes BS ISO/IEC 27001:2005/BS 7799-2:2005

  • BS ISO/IEC 27002:2013 Information technology. Security techniques. Code of practice for information security controls

Supersedes BS ISO/IEC 27002:2005

  • BS ISO/IEC/IEEE 29119-1:2013 Software and systems engineering. Software testing. Concepts and definitions

Supersedes BS 7925-1:1998

  • BS ISO/IEC/IEEE 29119-2:2013 Software and systems engineering. Software testing. Test processes
  • BS ISO/IEC/IEEE 29119-3:2013 Software and systems engineering. Software testing. Test documentation
  • BS ISO 30021:2013 Plastics. Burning behavior. Intermediate-scale fire-resistance testing of fibre-reinforced polymer composites
  • BS ISO/IEC 40500:2012 Information technology. W3C Web Content Accessibility Guidelines (WCAG) 2.0
  • BS IEC 62396-3:2013 Process management for avionics. Atmospheric radiation effects. System design optimization to accommodate the single event effects (SEE) of atmospheric radiation

Supersedes DD IEC/TS 62396-3:2008

  • BS IEC 62396-4:2013 Process management for avionics. Atmospheric radiation effects. Design of high voltage aircraft electronics managing potential single event effects

Supersedes DD IEC/TS 62396-4:2008

  • BS IEC 62443-3-3:2013 Industrial communication networks. Network  and system security. System security requirements and security levels
  • BS IEC 62483:2013 Environmental acceptance requirements for tin whisker susceptibility of tin and tin alloy surface finishes on semiconductor devices

Supersedes DD IEC/PAS 62483:2006

Published documents
  • PD 8010-5:2013 Pipeline systems. Subsea pipelines. Guide to operational practice
  • PD ISO/TS 8611-4:2013 Pallets for materials handling. Flat pallets. Procedure for predicting creep responses in stiffness tests for plastic pallets using regression analyses
  • PD ISO/TR 11371:2013 Pulps. Basic guidelines for laboratory refining
  • PD ISO/TS 13582:2013 Health informatics. Sharing of OID registry information
  • PD CEN/TS 13714:2013 Characterization of sludges. Sludge management in relation to use or disposal

Supersedes PD CEN/TR 13714:2010

  • PD CEN/TR 15449-4:2013 Geographic information. Spatial Data Infrastructure. Service centric view

Together with PD CEN/TR 15449-1:2012, PD CEN/TR 15449-2:2012 and PD CEN/TR 15449-3:2012, it Supersedes PD CEN/TR 15449:2011, which is withdrawn

  • PD CEN ISO/TS 15530-1:2013 Geometrical product specifications (GPS). Coordinate measuring machines (CMM): Technique for determining the uncertainty of measurement. Overview and metrological characteristics
  • PD ISO/TS 15638-6:2013 Intelligent transport systems. Framework for collaborative Telematics Applications for Regulated commercial freight Vehicles (TARV). Regulated applications
  • PD ISO/TS 15638-8:2013 Intelligent transport systems. Framework for collaborative Telematics Applications for Regulated commercial freight Vehicles (TARV). Vehicle access monitoring (VAM)
  • PD ISO/TS 15638-12:2013 Intelligent transport systems. Framework for collaborative Telematics Applications for Regulated commercial freight Vehicles (TARV). Vehicle mass monitoring (VMM)
  • PD ISO/TS 15638-14:2013 Intelligent transport systems. Framework for collaborative Telematics Applications for Regulated commercial freight Vehicles (TARV). Vehicle access control (VAC)
  • PD ISO/TS 15638-16:2013 Intelligent transport systems. Framework for collaborative Telematics Applications for Regulated commercial freight Vehicles (TARV). Vehicle speed monitoring (VSM)
  • PD ISO/TS 15638-17:2013 Intelligent transport systems. Framework for collaborative Telematics Applications for Regulated commercial freight Vehicles (TARV). Consignment and location monitoring (CLM)
  • PD ISO/TS 15638-19:2013 Intelligent transport systems. Framework for collaborative Telematics Applications for Regulated commercial freight Vehicles (TARV). Vehicle parking facilities (VPF)
  • PD ISO/TS 16097:2013 Vulcanized crumb rubber. Evaluation procedures
  • PD CEN ISO/TS 16190:2013 Footwear. Critical substances potentially present in footwear and footwear components. Test method to quantitatively determine polycyclic aromatic hydrocarbons (PAH) in footwear materials
  • PD ISO/TR 16335:2013 Corrosion of metals and alloys. Corrosion tests in artificial atmospheres. Guidelines for selection of accelerated corrosion test for product qualification
  • PD CEN/TS 16524:2013 Mechanical products. Methodology for reduction of environmental impacts in product design and development
  • PD CEN/TR 16557:2013 Automotive fuels. High FAME diesel fuel blends (B11-B30). Background to the parameters required and their respective limits and determination
  • PD CEN/TR 16563:2013 Principles of the equivalent durability procedure
  • PD CEN/CLC/TR 16567:2013 Energy Efficiency Obligation Schemes in Europe. Overview and analysis of main features and possibilities for harmonisation
  • PD ISO/TR 17219:2013 Review of human smoking behavior and recommendations for a new ISO standard for the machine smoking of cigarettes
  • PD CEN ISO/TR 24014-2:2013 Public transport. Interoperable fare management system. Business practices

Together with PD CEN ISO/TR 24014-1 and PD CEN ISO/TR 24014-3:2013 it supersedes BS EN ISO 24014-1:2007, which will be withdrawn upon publication of PD CEN ISO/TR 24014-1

  • PD ISO/IEC TR 27019:2013 Information technology. Security techniques. Information security management guidelines based on ISO/IEC 27002 for process control systems specific to the energy utility industry
  • PD CLC/TS 50136-9:2013 Alarm systems. Alarm transmission systems and equipment. Requirements for common protocol for alarm transmission using the Internet protocol
  • PD CLC/TR 50422:2013 Guide for the application of the European Standard EN 50160

Supersedes PD CLC/TR 50422:2003

  • PD CLC/TS 50607:2013 Satellite signal distribution over a single coaxial cable. Second generation
  • PD IEC/TR 61340-1:2012 Electrostatics. Electrostatic phenomena. Principles and measurements
  • PD IEC/TR 61850-90-4:2013 Communication networks and systems for power utility automation. Network engineering guidelines
  • PD IEC/TS 62647-22:2013 Process management for avionics. Aerospace and defence electronic systems containing leadfree solder. Technical guidelines
  • PD IEC/TS 62656-2:2013 Standardized product ontology register and transfer by spreadsheets. Application guide for use with the IEC common data dictionary (CDD)
  • PD IEC/TR 62799:2013 Models for evaluation of thermal hazard in medical diagnostic ultrasonic fields
  • PD IEC/TR 62836:2013 Measurement of internal electric field in insulating materials. Pressure wave propagation method
Corrigenda to British standards and updated British standards

Most British amendments are not issued separately. Those that make significant changes to a standard are incorporated into the standard which is re-issued as a new edition. All amendments to date of despatch are included within any main publication when ordered for the first time. The following amended standards and corrigenda to British standards were made available last month.

  • BS 6989:1989 (ISO 8456:1985) Guide to Safety of storage equipment for loose bulk materials

CORRIGENDUM 1

  • BS 8006-2:2011 Code of practice for strengthened/reinforced  soils. Soil nail design

CORRIGENDUM 1

  • BS EN 845-1:2013 Specification for ancillary components for masonry. Wall ties, tension straps, hangers and brackets

CORRIGENDUM 1

  • BS EN 845-2:2013 Specification for ancillary components for masonry. Lintels

CORRIGENDUM 1

  • BS EN 845-3:2013 Specification for ancillary components for masonry. Bed joint reinforcement of steel meshwork

CORRIGENDUM 1

  • BS EN 1912:2012 Structural Timber. Strength classes. Assignment of visual grades and species

CORRIGENDUM 1

  • BS EN 2043:2013 Aerospace series. Metallic materials. General requirements for semi-finished product qualification (excluding forgings and castings)

CORRIGENDUM 1

  • BS EN 4701-001:2013 Aerospace series. Connectors, optical, rectangular, modular, operating temperature 125ºC, for EN 4531-101 contacts. Technical specification

CORRIGENDUM 1

  • BS EN ISO 10517:2009+A1:2013 Powered hand-held hedge trimmers. Safety

AMENDMENT 1

  • BS EN ISO 10579:2013 Geometrical product specifications (GPS). Dimensioning and tolerancing. Non-rigid parts

CORRIGENDUM 1

  • BS EN ISO 11980:2012 Ophthalmic optics. Contact lenses and contact lens care products. Guidance for clinical investigations

CORRIGENDUM 1

  • BS EN 12221-2:2008+A1:2013 Child use and care articles. Changing units for domestic use. Test methods

AMENDMENT 1

  • BS EN 12602:2008+A1:2013 Prefabricated reinforced components of autoclaved aerated concrete

CORRIGENDUM 2

  • BS EN 12831:2003 Heating systems in buildings. Method for calculation of the design heat load

CORRIGENDUM 2

  • BS EN 13001-3-1:2012+A1:2013 Cranes. General Design. Limit States and proof competence of steel structure

AMENDMENT 1

  • BS EN 13445-1:2009 Unfired pressure vessels. General

CORRIGENDUM 4

  • BS EN 13445-2:2009+A2:2012 Unfired pressure vessels. Materials

CORRIGENDUM 4

  • BS EN 13445-3:2009+A1:2012 Unfired pressure vessels. Design

CORRIGENDUM 4

  • BS EN 13445-4:2009+A1:2011 Unfired pressure vessels. Fabrication

CORRIGENDUM 4

  • BS EN 13445-5:2009+A4:2013 Unfired pressure vessels. Inspection and testing

AMENDMENT 4

  • BS EN 13445-6:2009 Unfired pressure vessels. Requirements for the design and fabrication of pressure vessels and pressure parts constructed from spheroidal graphite cast iron

CORRIGENDUM 4

  • BS EN 13445-8:2009 Unfired pressure vessels. Additional requirements for pressure vessels of aluminium and aluminium alloys

CORRIGENDUM 4

  • BS EN 13480-4:2012+A1:2013 Metallic industrial piping. Fabrication and installation

AMENDMENT 1

  • BS EN 13480-5:2012+A1:2013 Metallic industrial piping. Inspection and testing

AMENDMENT 1

  • BS EN 14336:2004 Heating systems in buildings. Installation and commissioning of water based heating systems

CORRIGENDUM 2

  • BS EN 16081:2011+A1:2013 Hyperbaric chambers. Specific requirements for fire extinguishing systems. Performance installation and testing

AMENDMENT 1

  • BS EN ISO 19902:2007+A1:2013 Petroleum and natural gas industries. Fixed steel offshore structures

AMENDMENT 1

  • BS EN 50117-2-1:2005+A2:2013 Coaxial cables. Sectional specification for cables used in cabled distribution networks. Indoor drop cables for systems operating at 5 MHz-1000 MHz

AMENDMENT 2

  • BS EN 50117-2-2:2004+A2:2013 Coaxial cables. Sectional specification for cables used in cabled distribution networks. Outdoor drop cables for systems operating at 5 MHz-1000 MHz

AMENDMENT 2

  • BS EN 50117-2-3:2004+A2:2013 Coaxial cables. Sectional specification for cables used in cabled distribution networks. Distribution and trunk cables for systems operating at 5 MHz-1000 MHz

AMENDMENT 2

  • BS EN 50117-2-4:2004+A2:2013 Coaxial cables. Sectional specification for cables used in cabled distribution networks. Indoor drop cables for systems operating at 5 MHz-3000 MHz

AMENDMENT 2

  • BS EN 50117-2-5:2004+A2:2013 Coaxial cables. Sectional specification for cables used in cabled distribution networks. Outdoor drop cables for systems operating at 5 MHz-3000 MHz

AMENDMENT 2

  • BS EN 50367:2012 Railway applications. Current collection systems. Technical criteria for the interaction between pantograph and overhead line (to achieve free access)

CORRIGENDUM 2

  • BS EN 50388:2012 Railway Applications. Power supply and rolling stock. Technical criteria for the coordination between power supply (substation) and rolling stock to achieve interoperability

CORRIGENDUM 3

  • BS EN 55016-2-3:2010+A1:2010 Specification for radio disturbance and immunity measuring apparatus and methods. Methods of measurement of disturbances and immunity. Radiated disturbance measurements

CORRIGENDUM 1

  • BS EN 55032:2012 Electromagnetic compatibility of multimedia equipment. Emission requirements

CORRIGENDUM 3

  • BS EN 60335-2-15:2002+A11:2013 Household and similar electrical appliances. Safety. Particular requirements for appliances for heating liquids

AMENDMENT 11

  • BS EN 60335-2-40:2003+A13:2012 Household and similar electrical appliances. Safety. Particular requirements for electrical heat pumps, air-conditioners and dehumidifiers

CORRIGENDUM 3

  • BS EN 60352-2:2006+A1:2013 Solderless connections. Crimped connections. General requirements, test methods and practical guidance

AMENDMENT 1

  • BS EN 61029-2-10:2010+A11:2013 Safety of transportable motor-operated electric tools. Particular requirements for cutting-off grinders

AMENDMENT 11

  • BS EN 61034-2:2005+A1:2013 Measurement of smoke density of cables burning under defined conditions. Test procedure and requirements

AMENDMENT 1

  • BS EN 61439-1:2009 Low-voltage switchgear and controlgear assemblies. General rules

CORRIGENDUM 1

  • BS EN 61439-3:2012 Low-voltage switchgear and controlgear assemblies. Distribution boards intended to be operated by ordinary persons (DBO)

CORRIGENDUM 1

  • PD CEN ISO/TR 9241-331:2013 Ergonomics of human-system interaction. Optical characteristics of autostereoscopic displays

CORRIGENDUM 1

  • BS ISO 10110-12:2007+A1:2013 Optics and photonics. Preparation of drawings for optical elements and systems. Aspheric surfaces

AMENDMENT 1

  • BS ISO 10317:2008+A1:2013 Rolling bearings. Tapered roller bearings. Designation system

AMENDMENT 1

  • BS ISO/IEC 10373-3:2010 Identification cards. Test methods. Integrated circuit cards with contacts and related interface devices

CORRIGENDUM 1

  • PD ISO/IEC TR 15443-1:2012 Information technology. Security techniques. Security assurance framework. Introduction and concepts

CORRIGENDUM 1

  • PD ISO/IEC TR 15443-2:2012 Information technology. Security techniques. Security assurance framework. Analysis

CORRIGENDUM 1

  • BS ISO/IEC 19794-6:2011 Information technology. Biometric data interchange formats. Iris image data

CORRIGENDUM 2

  • PD CEN ISO/TR 24014-3:2013 Public transport. Interoperable fare management system. Complementary concepts to Part 1 for multi-application media

CORRIGENDUM 1

  • BS ISO 27729:2012 Information and documentation. International standard name identifier (ISNI)

CORRIGENDUM 1

  • DD IEC/TS 60479-1:2005 Effects of current on human beings and livestock. General aspects

CORRIGENDUM 2

  • PD 5500:2012+A2:2013 Specification for unfired fusion welded pressure vessels

AMENDMENT 2

  • PD CEN ISO/TR 12296:2013 Ergonomics. Manual handling of people in the healthcare sector

CORRIGENDUM 1

  • PD CEN ISO/TR 24475:2013 Cosmetics. Good Manufacturing Practices. General training document

CORRIGENDUM 1

British standards withdrawn
  • BS 4193-9:1982 (ISO 6262-1:1982) Hardmetal insert tooling. Specification for end mills with indexable inserts and flatted parallel shank

Superseded by BS ISO 6262-1:2013

  • BS 4193-10:1982 (ISO 6262-2:1982) Hardmetal insert tooling. Specification for end mills with indexable inserts and Morse taper shank

Superseded by BS ISO 6262-2:2013

  • BS 4193-12:1984 (ISO 6986:1983) Hardmetal insert tooling. Specification for dimensions of side and face milling and slotting cutters with indexable inserts

Superseded by BS ISO 6986:2013

  • BS 7011-3.2:1998 (ISO 8255-2:1997) Consumable accessories for light microscopes. Cover glasses. Specification for materials and quality of finish

Superseded by BS ISO 8255-2:2013

  • BS 7655-1.4:2000 Specification for insulating and sheathing materials for cables. Elastomeric insulating compounds. Oil resisting types

This standard is withdrawn as the insulating material this standard describes (type OR1) is now obsolete

  • BS 7925-1:1998 Software testing. Vocabulary

Superseded by BS ISO/IEC/IEEE 29119-1:2013

  • DD CEN/TS 81-82:2008 Safety rules for the construction and installation of lifts. Existing lifts. Improvement of the accessibility of existing lifts for persons including persons with disability

Superseded by BS EN 81-82:2013

  • BS EN 600:1996 (BS 3704:1996) Natural rubber latex male condoms

Superseded by BS EN ISO 4074:2002

  • BS EN 836:1997+A4:2011 Garden equipment. Powered lawnmowers. Safety

Superseded by BS EN ISO 5395-1:2013, BS EN ISO 5395-2:2013 and BS EN ISO 5395-3:2013

  • BS EN 957-1:2005 Stationary training equipment. General safety requirements and test methods

Superseded by BS EN ISO 20957-1:2013

  • BS EN 1088:1995+A2:2008 Safety of machinery. Interlocking devices associated with guards. Principles for design and selection

Superseded by BS EN ISO 14119:2013

  • BS EN 1836:2005 Personal eye-equipment. Sunglasses and sunglare filters for general use and filters for direct observation of the sun

Superseded by BS EN ISO 12311:2013 and BS EN ISO 12312-1:2013

  • BS EN ISO 12209-1:2001 Gas cylinders. Outlet connections for gas cylinder valves for compressed breathable air. Yoke type connections

Superseded by BS EN ISO 12209:2013

  • BS EN ISO 12209-2:2001 Gas cylinders. Outlet connections for gas cylinder valves for compressed breathable air. Threaded connections

Superseded by BS EN ISO 12209:2013

  • BS EN ISO 12209-3:2001 Gas cylinders. Outlet connections for gas cylinder valves for compressed breathable air. Adaptor for 230 bar valves

Superseded by BS EN ISO 12209:2013

  • DD CEN/TS 13547:2006 Industrial valves. Copper alloy ball valves

Superseded by BS EN 13547:2013

  • PD CEN/TR 15449:2011 Geographic information. Standards, specifications, technical reports and guidelines, required to implement Spatial Data Infrastructures

Superseded by PD CEN/TR 15449-1:2012, PD CEN/TR 15449-2:2012, PD CEN/TR 15449-3:2012 and PD CEN/TR 15449-4:2013

  • PD CEN/TS 16320:2012 Fertilizers. Determination of trace elements. Determination of mercury by vapour generation (VG) after aqua regia dissolution

Superseded by BS EN 16320:2013

  • BS EN 60730-2-9:2002 Automatic electrical controls for household and similar use. Particular requirements for temperature sensing controls

Superseded by BS EN 60730-2-9:2010

  • BS EN 61029-1:2009 Safety of transportable motor-operated electric tools. General requirements

Superseded by BS EN 61029-1:2009+A11:2010

  • BS EN 61210:1995 Connecting devices. Flat quick-connect terminations for electrical copper conductors. Safety requirements

Superseded by BS EN 61210:2010

  • BS EN 61347-2-12:2005 Lamp controlgear. Particular requirements for d.c. or a.c. supplied electronic Ballasts for discharge lamps (excluding fluorescent lamps)

Superseded by BS EN 61347-2-12:2005+A1:2010

  • BS EN 61400-1:2005 Wind turbines. Design requirements

Superseded by BS EN 61400-1:2005+A1:2010

  • BS EN 62056-61:2007 Electricity metering. Data exchange for meter reading, tariff and load control. Object identification system (OBIS)

Superseded by BS EN 62056-6-1:2013

  • BS EN 62056-62:2007 Electricity metering. Data exchange for meter reading, tariff and load control. Interface classes

Superseded by BS EN 62056-6-2:2013

  • BS EN 62068-1:2003 Electrical insulation systems. Electrical stresses produced by repetitive impulses. General method of evaluation of electrical endurance

Superseded by BS EN 62068:2013

  • BS ISO/IEC 1539-3:1999 Information technology. Programming languages. FORTRAN. Conditional compilation

This standard is withdrawn as the adopted ISO standard has been withdrawn

  • BS ISO 21747:2006 Statistical methods. Process performance and capability statistics for measured quality characteristics

Superseded by BS ISO 22514-2:2013

  • BS ISO 23273-2:2006 Fuel cell road vehicles. Safety specifications. Protection against hydrogen hazards for vehicles fuelled with compressed hydrogen

Superseded by BS ISO 23273:2013

  • DD CLC/TS 50131-2-7-1:2009 Alarm systems. Intrusion and hold-up systems. Intrusion detectors. Glass break detectors (acoustic)

Superseded by BS EN 50131-2-7-1:2012

  • DD CLC/TS 50131-2-7-2:2009 Alarm systems. Intrusion and hold-up systems. Intrusion detectors. Glass break detectors (passive)

Superseded by BS EN 50131-2-7-2:2012

  • DD CLC/TS 50131-2-7-3:2009 Alarm systems. Intrusion and hold-up systems. Intrusion detectors. Glass break detectors (active)

Superseded by BS EN 50131-2-7-3:2012

  • BS IEC 61710:2000 Power law model. Goodness-of-fit tests and estimation methods

Superseded by BS EN 61710:2013

  • DD IEC/TS 62396-3:2008 Process management for avionics. Atmospheric radiation effects. Optimising system design to accommodate the single event effects (SEE) of atmospheric radiation

Superseded by BS IEC 62396-3:2013

  • DD IEC/TS 62396-4:2008 Process management for avionics. Atmospheric radiation effects. Guidelines for designing with high voltage aircraft electronics and potential single event effects

Superseded by BS IEC 62396-4:2013

  • DD IEC/PAS 62483:2006 Test method for measuring whisker growth on tin and tin alloy surface finishes

Superseded by BS IEC 62483:2013

  • DD IEC/PAS 62612:2009 Self-ballasted LED-lamps for general lighting services. Performance requirements

Superseded by BS EN 62612:2013

Published in international.