ASTM STANDARDS

Issue 50 – June 2013

To purchase PDF or hard copy ASTM Standards, please email enquiries@standards.co.nz or call 0800 782 632 during business hours.

  • A65 Standard Specification for Steel Track Spikes has been reapproved, available as A65-07(2013) developed by Committee A01.01, ASTM BOS Volume 01.04.
  • A66 Standard Specification for Steel Screw Spikes has been reapproved, available as A66-07(2013) developed by Committee A01.01, ASTM BOS Volume 01.04.
  • A121 Standard Specification for Metallic-Coated Carbon Steel Barbed Wire has been revised to A121-13 developed by Committee A05.12, ASTM BOS Volume 01.06.
  • A182/A182M Standard Specification for Forged or Rolled Alloy and Stainless Steel Pipe Flanges, Forged Fittings, and Valves and Parts for High-Temperature Service has been revised to A182/A182M-13 developed by Committee A01.22, ASTM BOS Volume 01.01.
  • A213/A213M Standard Specification for Seamless Ferritic and Austenitic Alloy-Steel Boiler, Superheater, and Heat-Exchanger Tubes has been revised to A213/A213M-13 developed by Committee A01.10, ASTM BOS Volume 01.01.
  • A289/A289M Standard Specification for Alloy Steel Forgings for Nonmagnetic Retaining Rings for Generators has been reapproved, available as A289/A289M-97(2013) developed by Committee A01.06, ASTM BOS Volume 01.05.
  • A312/A312M Standard Specification for Seamless, Welded, and Heavily Cold Worked Austenitic Stainless Steel Pipes has been revised to A312/A312M-13 developed by Committee A01.10, ASTM BOS Volume 01.01.
  • A351/A351M Standard Specification for Castings, Austenitic, for Pressure-Containing Parts has been revised to A351/A351M-13 developed by Committee A01.18, ASTM BOS Volume 01.02.
  • A376/A376M Standard Specification for Seamless Austenitic Steel Pipe for High-Temperature Service has been revised (with title change) to A376/A376M-13 developed by Committee A01.10, ASTM BOS Volume 01.01.
  • A384/A384M Standard Practice for Safeguarding Against Warpage and Distortion During Hot-Dip Galvanizing of Steel Assemblies has been reapproved, available as A384/A384M-07(2013) developed by Committee A05.13, ASTM BOS Volume 01.06.
  • A407 Standard Specification for Steel Wire, Cold-Drawn, for Coiled-Type Springs has been reapproved, available as A407-07(2013) developed by Committee A01.03, ASTM BOS Volume 01.03.
  • A554 Standard Specification for Welded Stainless Steel Mechanical Tubing has been revised to A554-13 developed by Committee A01.10, ASTM BOS Volume 01.01.
  • A568/A568M Standard Specification for Steel, Sheet, Carbon, Structural, and High-Strength, Low-Alloy, Hot-Rolled and Cold-Rolled, General Requirements for has been revised to A568/A568M-13 developed by Committee A01.19, ASTM BOS Volume 01.03.
  • A644 Standard Terminology Relating to Iron Castings has been revised to A644-13 developed by Committee A04.91, ASTM BOS Volume 01.02.
  • A703/A703M Standard Specification for Steel Castings, General Requirements, for Pressure-Containing Parts has been revised to A703/A703M-13 developed by Committee A01.18, ASTM BOS Volume 01.02.
  • A709/A709M Standard Specification for Structural Steel for Bridges has been revised to A709/A709M-13 developed by Committee A01.02, ASTM BOS Volume 01.04.
  • A789/A789M Standard Specification for Seamless and Welded Ferritic/Austenitic Stainless Steel Tubing for General Service has been revised to A789/A789M-13 developed by Committee A01.10, ASTM BOS Volume 01.01.
  • A790/A790M Standard Specification for Seamless and Welded Ferritic/Austenitic Stainless Steel Pipe has been revised to A790/A790M-13 developed by Committee A01.10, ASTM BOS Volume 01.01.
  • A857/A857M Standard Specification for Steel Sheet Piling, Cold Formed, Light Gage has been reapproved, available as A857/A857M-07(2013) developed by Committee A01.02, ASTM BOS Volume 01.04.
  • A902 Standard Terminology Relating to Metallic Coated Steel Products has been revised to A902-13 developed by Committee A05.18, ASTM BOS Volume 01.06.
  • A931 Standard Test Method for Tension Testing of Wire Ropes and Strand has been reapproved, available as A931-08(2013) developed by Committee A01.03, ASTM BOS Volume 01.03.
  • A938 Standard Test Method for Torsion Testing of Wire has been reapproved, available as A938-07(2013) developed by Committee A01.03, ASTM BOS Volume 01.03.
  • A941 Standard Terminology Relating to Steel, Stainless Steel, Related Alloys, and Ferroalloys has been revised to A941-13a developed by Committee A01.92, ASTM BOS Volume 01.01.
  • A957/A957M Standard Specification for Investment Castings, Steel and Alloy, Common Requirements, for General Industrial Use has been revised to A957/A957M-13 developed by Committee A01.18, ASTM BOS Volume 01.02.
  • A962/A962M Standard Specification for Common Requirements for Bolting Intended for Use at Any Temperature from Cryogenic to the Creep Range has been revised to A962/A962M-13 developed by Committee A01.22, ASTM BOS Volume 01.01.
  • A970/A970M Standard Specification for Headed Steel Bars for Concrete Reinforcement has been revised to A970/A970M-13 developed by Committee A01.05, ASTM BOS Volume 01.04.
  • A1003/A1003M Standard Specification for Steel Sheet, Carbon, Metallic- and Nonmetallic-Coated for Cold-Formed Framing Members has been revised to A1003/A1003M-13a developed by Committee A05.11, ASTM BOS Volume 01.06.
  • A1022/A1022M Standard Specification for Deformed and Plain Stainless Steel Wire and Welded Wire for Concrete Reinforcement has been revised to A1022/A1022M-13 developed by Committee A01.05, ASTM BOS Volume 01.04.
  • A1035/A1035M Standard Specification for Deformed and Plain, Low-carbon, Chromium, Steel Bars for Concrete Reinforcement has been revised to A1035/A1035M-13 developed by Committee A01.05, ASTM BOS Volume 01.04.
  • A1041/A1041M Standard Specification for Pressure Vessel Plates, Alloy Steel, Higher Strength Chromium-Molybdenum-Tungsten (Withdrawn 2013) has been withdrawn, with no replacement. A1041/A1041M-04(2009) developed by Committee A01.11, ASTM BOS Volume 01.04.
  • A1059/A1059M Standard Specification for Zinc Alloy Thermo-Diffusion Coatings (TDC) on Steel Fasteners, Hardware, and Other Products has been reapproved, available as A1059/A1059M-08(2013) developed by Committee A05.13, ASTM BOS Volume 01.06.
  • B63 Standard Test Method for Resistivity of Metallically Conducting Resistance and Contact Materials has been reapproved, available as B63-07(2013) developed by Committee B02.10, ASTM BOS Volume 02.04.
  • B70 Standard Test Method for Change of Resistance With Temperature of Metallic Materials for Electrical Heating has been reapproved, available as B70-90(2013) developed by Committee B02.10, ASTM BOS Volume 02.04.
  • B76 Standard Test Method for Accelerated Life of Nickel-Chromium and Nickel-Chromium-Iron Alloys for Electrical Heating has been reapproved, available as B76-90(2013) developed by Committee B02.10, ASTM BOS Volume 02.04.
  • B77 Standard Test Method for Thermoelectric Power of Electrical-Resistance Alloys has been reapproved, available as B77-07(2013) developed by Committee B02.10, ASTM BOS Volume 02.04.
  • B78 Standard Test Method of Accelerated Life of Iron-Chromium-Aluminum Alloys for Electrical Heating has been reapproved, available as B78-90(2013) developed by Committee B02.10, ASTM BOS Volume 02.04.
  • B84 Standard Test Method for Temperature-Resistance Constants of Alloy Wires for Precision Resistors has been reapproved, available as B84-07(2013) developed by Committee B02.10, ASTM BOS Volume 02.04.
  • B114 Standard Test Method for Temperature-Resistance Constants of Sheet Materials for Shunts and Precision Resistors has been reapproved, available as B114-07(2013) developed by Committee B02.10, ASTM BOS Volume 02.04.
  • B136 Standard Method for Measurement of Stain Resistance of Anodic Coatings on Aluminum has been reapproved, available as B136-84(2013) developed by Committee B08.07, ASTM BOS Volume 02.05.
  • B221 Standard Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wire, Profiles, and Tubes has been revised to B221-13 developed by Committee B07.03, ASTM BOS Volume 02.02.
  • B221M Standard Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wire, Profiles, and Tubes (Metric) has been revised to B221M-13 developed by Committee B07.03, ASTM BOS Volume 02.02.
  • B267 Standard Specification for Wire for Use In Wire-Wound Resistors has been reapproved, available as B267-07(2013) developed by Committee B02.10, ASTM BOS Volume 02.04.
  • B438 Standard Specification for Bronze-Base Powder Metallurgy (PM) Bearings (Oil-Impregnated) has been revised to B438-13 developed by Committee B09.04, ASTM BOS Volume 02.05.
  • B457 Standard Test Method for Measurement of Impedance of Anodic Coatings on Aluminum has been reapproved, available as B457-67(2013) developed by Committee B08.07, ASTM BOS Volume 02.05.
  • B549 Standard Specification for Concentric-Lay-Stranded Aluminum Conductors, Aluminum-Clad Steel Reinforced for Use in Overhead Electrical Conductors has been revised to B549-13 developed by Committee B01.07, ASTM BOS Volume 02.03.
  • B594 Standard Practice for Ultrasonic Inspection of Aluminum-Alloy Wrought Products has been revised (with title change) to B594-13 developed by Committee B07.03, ASTM BOS Volume 02.02.
  • B603 Standard Specification for Drawn or Rolled Iron-Chromium-Aluminum Alloys for Electrical Heating Elements has been reapproved, available as B603-07(2013) developed by Committee B02.10, ASTM BOS Volume 02.04.
  • B753 Standard Specification for Thermostat Component Alloys has been reapproved, available as B753-07(2013) developed by Committee B02.10, ASTM BOS Volume 02.04.
  • B760 Standard Specification for Tungsten Plate, Sheet, and Foil has been reapproved, available as B760-07(2013) developed by Committee B10.04, ASTM BOS Volume 02.04.
  • B777 Standard Specification for Tungsten Base, High-Density Metal has been reapproved, available as B777-07(2013) developed by Committee B10.04, ASTM BOS Volume 02.04.
  • B811 Standard Specification for Wrought Zirconium Alloy Seamless Tubes for Nuclear Reactor Fuel Cladding has been revised to B811-13 developed by Committee B10.02, ASTM BOS Volume 02.04.
  • B849 Standard Specification for Pre-Treatments of Iron or Steel for Reducing Risk of Hydrogen Embrittlement has been reapproved, available as B849-02(2013) developed by Committee B08.02, ASTM BOS Volume 02.05.
  • B856 Standard Specification for Concentric-Lay-Stranded Aluminum Conductors, Coated Steel Supported (ACSS) has been revised to B856-13 developed by Committee B01.07, ASTM BOS Volume 02.03.
  • B879 Standard Practice for Applying Non-Electrolytic Conversion Coatings on Magnesium and Magnesium Alloys has been reapproved, available as B879-97(2013) developed by Committee B08.07, ASTM BOS Volume 02.05.
  • B883 Standard Specification for Metal Injection Molding (MIM) Ferrous Materials has been editorially changed, available as B883-10e1 developed by Committee B09.11, ASTM BOS Volume 02.05.
  • B893 Standard Specification for Hard-Coat Anodizing of Magnesium for Engineering Applications has been reapproved, available as B893-98(2013) developed by Committee B08.07, ASTM BOS Volume 02.05.
  • B912 Standard Specification for Passivation of Stainless Steels Using Electropolishing has been reapproved, available as B912-02(2013) developed by Committee B08.07, ASTM BOS Volume 02.05.
  • B914 Standard Practice for Color Codes on Zinc and Zinc Alloy Ingot for Use in Hot-Dip Galvanizing of Steel has been revised to B914-13 developed by Committee B02.04, ASTM BOS Volume 02.04.
  • B915 Standard Test Method for Measuring Static Heat Resistance of Self-Cleaning Oven Coating has been reapproved (with editorial change), available as B0915-01(2013)e1 developed by Committee B08.12, ASTM BOS Volume 02.05.
  • B916 Standard Test Method for Adherence of Porcelain Enamel Coatings to Sheet Metal has been editorially changed, available as B916-01(2013)e1 developed by Committee B08.12, ASTM BOS Volume 02.05.
  • B921 Standard Specification for Non-hexavalent Chromium Conversion Coatings on Aluminum and Aluminum Alloys has been reapproved, available as B921-08(2013) developed by Committee B08.07, ASTM BOS Volume 02.05.
  • B947 Standard Practice for Hot Rolling Mill Solution Heat Treatment for Aluminum Alloy Plate has been reapproved, available as B947-06(2013) developed by Committee B07.03, ASTM BOS Volume 02.02.
  • B988 Standard Specification for Powder Metallurgy (PM) Titanium and Titanium Alloy Structural Components is a new standard, now available. B988-13 developed by Committee B09.11, ASTM BOS Volume 02.05.
  • C168 Standard Terminology Relating to Thermal Insulation has been revised to C168-13 developed by Committee C16.94, ASTM BOS Volume 04.06.
  • C241/C241M Standard Test Method for Abrasion Resistance of Stone Subjected to Foot Traffic has been revised to C241/C241M-13 developed by Committee C18.01, ASTM BOS Volume 04.07.
  • C507M Standard Specification for Reinforced Concrete Elliptical Culvert, Storm Drain, and Sewer Pipe (Metric) has been revised to C507M-13b developed by Committee C13.02, ASTM BOS Volume 04.05.
  • C635/C635M Standard Specification for the Manufacture, Performance, and Testing of Metal Suspension Systems for Acoustical Tile and Lay-in Panel Ceilings has been revised to C635/C635M-13 developed by Committee E33.04, ASTM BOS Volume 04.06.
  • C636/C636M Standard Practice for Installation of Metal Ceiling Suspension Systems for Acoustical Tile and Lay-In Panels has been revised to C636/C636M-13 developed by Committee E33.04, ASTM BOS Volume 04.06.
  • C692 Standard Test Method for Evaluating the Influence of Thermal Insulations on External Stress Corrosion Cracking Tendency of Austenitic Stainless Steel has been revised to C692-13 developed by Committee C16.31, ASTM BOS Volume 04.06.
  • C795 Standard Specification for Thermal Insulation for Use in Contact with Austenitic Stainless Steel has been reapproved, available as C795-08(2013) developed by Committee C16.20, ASTM BOS Volume 04.06.
  • C981 Standard Guide for Design of Built-Up Bituminous Membrane Waterproofing Systems for Building Decks has been reapproved, available as C981-05(2013) developed by Committee D08.22, ASTM BOS Volume 04.04.
  • C1009 Standard Guide for Establishing and Maintaining a Quality Assurance Program for Analytical Laboratories Within the Nuclear Industry has been revised to C1009-13a developed by Committee C26.08, ASTM BOS Volume 12.01.
  • C1072 Standard Test Methods for Measurement of Masonry Flexural Bond Strength has been revised to C1072-13 developed by Committee C15.04, ASTM BOS Volume 04.05.
  • C1174 Standard Practice for Prediction of the Long-Term Behavior of Materials, Including Waste Forms, Used in Engineered Barrier Systems (EBS) for Geological Disposal of High-Level Radioactive Waste has been reapproved, available as C1174-07(2013) developed by Committee C26.13, ASTM BOS Volume 12.01.
  • C1183/C1183M Standard Test Method for Extrusion Rate of Elastomeric Sealants has been revised (with designation change) to C1183/C1183M-13 developed by Committee C24.20, ASTM BOS Volume 04.07.
  • C1216/C1216M Standard Test Method for Adhesion and Cohesion of One-Part Elastomeric Solvent Release Sealants has been revised (with designation change) to C1216/C1216M-13 developed by Committee C24.30, ASTM BOS Volume 04.07.
  • C1289 Standard Specification for Faced Rigid Cellular Polyisocyanurate Thermal Insulation Board has been revised to C1289-13 developed by Committee C16.22, ASTM BOS Volume 04.06.
  • C1330 Standard Specification for Cylindrical Sealant Backing for Use with Cold Liquid-Applied Sealants has been reapproved, available as C1330-02(2013) developed by Committee C24.10, ASTM BOS Volume 04.07.
  • C1410 Standard Specification for Cellular Melamine Thermal and Sound-Absorbing Insulation has been revised to C1410-13 developed by Committee C16.22, ASTM BOS Volume 04.06.
  • C1440 Standard Specification for Thermoplastic Elastomeric (TPE) Gasket Materials for Drain, Waste, and Vent (DWV), Sewer, Sanitary and Storm Plumbing Systems has been reapproved, available as C1440-08(2013) developed by Committee A04.75, ASTM BOS Volume 01.02.
  • C1461 Standard Specification for Mechanical Couplings Using Thermoplastic Elastomeric (TPE) Gaskets for Joining Drain, Waste, and Vent (DWV), Sewer, Sanitary, and Storm Plumbing Systems for Above and Below Ground Use has been reapproved, available as C1461-08(2013) developed by Committee A04.75, ASTM BOS Volume 01.02.
  • C1503 Standard Specification for Silvered Flat Glass Mirror has been reapproved, available as C1503-08(2013) developed by Committee C14.08, ASTM BOS Volume 15.02.
  • C1521 Standard Practice for Evaluating Adhesion of Installed Weatherproofing Sealant Joints has been revised to C1521-13 developed by Committee C24.30, ASTM BOS Volume 04.07.
  • C1522 Standard Test Method for Extensibility After Heat Aging of Cold Liquid-Applied Elastomeric Waterproofing Membranes has been reapproved, available as C1522-05(2013) developed by Committee D08.22, ASTM BOS Volume 04.04.
  • C1563 Standard Test Method for Gaskets for Use in Connection with Hub and Spigot Cast Iron Soil Pipe and Fittings for Sanitary Drain, Waste, Vent, and Storm Piping Applications has been reapproved, available as C1563-08(2013) developed by Committee A04.75, ASTM BOS Volume 01.02.
  • C1579 Standard Test Method for Evaluating Plastic Shrinkage Cracking of Restrained Fiber Reinforced Concrete (Using a Steel Form Insert) has been revised to C1579-13 developed by Committee C09.42, ASTM BOS Volume 04.02.
  • C1583/C1583M Standard Test Method for Tensile Strength of Concrete Surfaces and the Bond Strength or Tensile Strength of Concrete Repair and Overlay Materials by Direct Tension (Pull-off Method) has been reinstated as C1583/C1583M-13 developed by Committee C09.25, ASTM BOS Volume 04.02.
  • C1696 Standard Guide for Industrial Thermal Insulation Systems has been revised to C1696-13a developed by Committee C16.40, ASTM BOS Volume 04.06.
  • C1728 Standard Specification for Flexible Aerogel Insulation has been revised to C1728-13 developed by Committee C16.23, ASTM BOS Volume 04.06.
  • C1773 Standard Test Method for Monotonic Axial Tensile Behavior of Continuous Fiber-Reinforced Advanced Ceramic Tubular Test Specimens at Ambient Temperature is a new standard, now available. C1773-13 developed by Committee C28.07, ASTM BOS Volume 15.01.
  • D88 Standard Test Method for Saybolt Viscosity has been reapproved, available as D88-07(2013) developed by Committee D08.05, ASTM BOS Volume 04.04.
  • D123 Standard Terminology Relating to Textiles has been editorially changed, available as D123-12e1 developed by Committee D13.92, ASTM BOS Volume 07.01.
  • D149 Standard Test Method for Dielectric Breakdown Voltage and Dielectric Strength of Solid Electrical Insulating Materials at Commercial Power Frequencies has been reapproved, available as D149-09(2013) developed by Committee D09.12, ASTM BOS Volume 10.01.
  • D297 Standard Test Methods for Rubber Products—Chemical Analysis has been revised to D297-13 developed by Committee D11.11, ASTM BOS Volume 09.01.
  • D396 Standard Specification for Fuel Oils has been revised to D396-13 developed by Committee D02.E0, ASTM BOS Volume 05.01.
  • D910 Standard Specification for Aviation Gasolines has been revised to D910-13 developed by Committee D02.J0.02, ASTM BOS Volume 05.01.
  • D975 Standard Specification for Diesel Fuel Oils has been revised to D975-13 developed by Committee D02.E0, ASTM BOS Volume 05.01.
  • D1488 Standard Test Method for Amylaceous Matter in Adhesives has been reapproved, available as D1488-00(2013) developed by Committee D14.30, ASTM BOS Volume 15.06.
  • D1490 Standard Test Method for Nonvolatile Content of Urea-Formaldehyde Resin Solutions has been reapproved, available as D1490-01(2013) developed by Committee D14.30, ASTM BOS Volume 15.06.
  • D1600 Standard Terminology for Abbreviated Terms Relating to Plastics has been revised to D1600-13 developed by Committee D20.92, ASTM BOS Volume 08.01.
  • D1610 Standard Practice for Conditioning Leather and Leather Products for Testing has been reapproved, available as D1610-01(2013) developed by Committee D31.07, ASTM BOS Volume 15.04.
  • D1669 Standard Practice for Preparation of Test Panels for Accelerated and Outdoor Weathering of Bituminous Coatings has been reapproved, available as D1669-07(2013) developed by Committee D08.02, ASTM BOS Volume 04.04.
  • D1732 Standard Practices for Preparation of Magnesium Alloy Surfaces for Painting has been reapproved, available as D1732-03(2013) developed by Committee B08.07, ASTM BOS Volume 02.05.
  • D1743 Standard Test Method for Determining Corrosion Preventive Properties of Lubricating Greases has been revised to D1743-13 developed by Committee D02.G0.06, ASTM BOS Volume 05.01.
  • D1813 Standard Test Method for Measuring Thickness of Leather Test Specimens has been revised to D1813-13 developed by Committee D31.07, ASTM BOS Volume 15.04.
  • D1835 Standard Specification for Liquefied Petroleum (LP) Gases has been revised to D1835-13 developed by Committee D02.H0, ASTM BOS Volume 05.01.
  • D2197 Standard Test Method for Adhesion of Organic Coatings by Scrape Adhesion has been revised to D2197-13 developed by Committee D01.23, ASTM BOS Volume 06.01.
  • D2307 Standard Test Method for Thermal Endurance of Film-Insulated Round Magnet Wire has been reapproved, available as D2307-07(2013) developed by Committee D09.10, ASTM BOS Volume 10.01.
  • D2346 Standard Test Method for Apparent Density of Leather has been revised to D2346-13 developed by Committee D31.03, ASTM BOS Volume 15.04.
  • D2464 Standard Specification for Threaded Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 80 has been revised to D2464-13 developed by Committee F17.10, ASTM BOS Volume 08.04.
  • D2699 Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel has been revised to D2699-12a developed by Committee D02.01, ASTM BOS Volume 05.05.
  • D2700 Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel has been revised to D2700-12a developed by Committee D02.01, ASTM BOS Volume 05.05.
  • D2746 Standard Test Method for Staining Tendency of Asphalt (Stain Index) has been reapproved, available as D2746-07(2013) developed by Committee D08.02, ASTM BOS Volume 04.04.
  • D2810 Standard Test Method for pH of Leather has been revised to D2810-13 developed by Committee D31.06, ASTM BOS Volume 15.04.
  • D2829 Standard Practice for Sampling and Analysis of Existing Built-Up Roof Systems has been reapproved, available as D2829-07(2013) developed by Committee D08.20, ASTM BOS Volume 04.04.
  • D2880 Standard Specification for Gas Turbine Fuel Oils has been revised to D2880-13 developed by Committee D02.E0, ASTM BOS Volume 05.01.
  • D2892 Standard Test Method for Distillation of Crude Petroleum (15-Theoretical Plate Column) has been revised to D2892-13 developed by Committee D02.08, ASTM BOS Volume 05.01.
  • D2941 Standard Test Method for Measuring Break Pattern of Leather (Break Scale) has been revised to D2941-13 developed by Committee D31.03, ASTM BOS Volume 15.04.
  • D3230 Standard Test Method for Salts in Crude Oil (Electrometric Method) has been revised to D3230-13 developed by Committee D02.03, ASTM BOS Volume 05.01.
  • D3241 Standard Test Method for Thermal Oxidation Stability of Aviation Turbine Fuels has been revised to D3241-13 developed by Committee D02.J0.03, ASTM BOS Volume 05.01.
  • D3251 Standard Test Method for Thermal Endurance Characteristics of Electrical Insulating Varnishes Applied Over Film-Insulated Magnet Wire has been reapproved, available as D3251-04(2013) developed by Committee D09.01, ASTM BOS Volume 10.02.
  • D3275 Standard Classification System for E-CTFE-Fluoroplastic Molding, Extrusion, and Coating Materials has been reapproved, available as D3275-08(2013) developed by Committee D20.15, ASTM BOS Volume 08.02.
  • D3312 Standard Test Method for Percent Reactive Monomer in Solventless Varnishes has been reapproved, available as D3312-04(2013) developed by Committee D09.01, ASTM BOS Volume 10.02.
  • D3377 Standard Test Method for Weight Loss of Solventless Varnishes has been reapproved, available as D3377-04(2013) developed by Committee D09.01, ASTM BOS Volume 10.02.
  • D3434 Standard Test Method for Multiple-Cycle Accelerated Aging Test (Automatic Boil Test) for Exterior Wet Use Wood Adhesives has been reapproved, available as D3434-00(2013) developed by Committee D14.30, ASTM BOS Volume 15.06.
  • D3452 Standard Practice for Rubber—Identification by Pyrolysis-Gas Chromatography has been reapproved, available as D3452-06(2012) developed by Committee D11.11, ASTM BOS Volume 09.01.
  • D3505 Standard Test Method for Density or Relative Density of Pure Liquid Chemicals has been editorially changed, available as D3505-12e1 developed by Committee D16.04, ASTM BOS Volume 06.04.
  • D3519 Standard Test Method for Foam in Aqueous Media (Blender Test) (Withdrawn 2013) has been withdrawn, with no replacement. D3519-88(2007) developed by Committee D02.L0.01, ASTM BOS Volume 05.01.
  • D3601 Standard Test Method for Foam In Aqueous Media (Bottle Test) (Withdrawn 2013) has been withdrawn, with no replacement. D3601-88(2007) developed by Committee D02.L0.01, ASTM BOS Volume 05.01.
  • D3635 Standard Test Method for Dissolved Copper In Electrical Insulating Oil By Atomic Absorption Spectrophotometry has been revised to D3635-13 developed by Committee D27.03, ASTM BOS Volume 10.03.
  • D3636 Standard Practice for Sampling and Judging Quality of Solid Electrical Insulating Materials has been revised to D3636-13 developed by Committee D09.94, ASTM BOS Volume 10.02.
  • D3676 Standard Specification for Rubber Cellular Cushion Used for Carpet or Rug Underlay has been revised to D3676-13 developed by Committee D20.22, ASTM BOS Volume 08.02.
  • D3699 Standard Specification for Kerosine has been revised to D3699-13 developed by Committee D02.E0, ASTM BOS Volume 05.01.
  • D3794 Standard Guide for Testing Coil Coatings has been reinstated as D3794-13 developed by Committee D01.53, ASTM BOS Volume 06.02.
  • D3878 Standard Terminology for Composite Materials has been reapproved, available as D3878-07(2013) developed by Committee D30.01, ASTM BOS Volume 15.03.
  • D3984 Standard Specification for Ethane Thermophysical Property Tables has been revised to D3984-13 developed by Committee D03.08, ASTM BOS Volume 05.06.
  • D4073 Standard Test Method for Tensile-Tear Strength of Bituminous Roofing Membranes has been reapproved, available as D4073-06(2013) developed by Committee D08.20, ASTM BOS Volume 04.04.
  • D4092 Standard Terminology for Plastics: Dynamic Mechanical Properties has been reapproved, available as D4092-07(2013) developed by Committee D20.10, ASTM BOS Volume 08.02.
  • D4391 Standard Terminology Relating to The Burning Behavior of Textiles has been editorially changed, available as D4391-93A(2013)e1 developed by Committee D13.92, ASTM BOS Volume 07.01.
  • D4426 Standard Test Method for Determination of Percent Nonvolatile Content of Liquid Phenolic Resins Used for Wood Laminating has been reapproved, available as D4426-01(2013) developed by Committee D14.30, ASTM BOS Volume 15.06.
  • D4444 Standard Test Method for Laboratory Standardization and Calibration of Hand-Held Moisture Meters has been revised to D4444-13 developed by Committee D07.01, ASTM BOS Volume 04.10.
  • D4448 Standard Guide for Sampling Ground-Water Monitoring Wells has been reapproved, available as D4448-01(2013) developed by Committee D34.01.02, ASTM BOS Volume 11.04.
  • D4512 Standard Test Method for Vibrated Apparent Packing Density of Fine Catalyst and Catalyst Carrier Particles and Powder has been editorially changed, available as D4512-03(2013)e1 developed by Committee D32.02, ASTM BOS Volume 05.05.
  • D4576 Standard Test Method for Mold Growth Resistance of Wet Blue has been reapproved, available as D4576-08(2013) developed by Committee D31.02, ASTM BOS Volume 15.04.
  • D4580/D4580M Standard Practice for Measuring Delaminations in Concrete Bridge Decks by Sounding has been revised (with designation change) to D4580/D4580M-12 developed by Committee D04.32, ASTM BOS Volume 04.03.
  • D4704 Standard Test Method for Tearing Strength, Tongue Tear of Leather has been revised to D4704-13 developed by Committee D31.07, ASTM BOS Volume 15.04.
  • D4705 Standard Test Method for Stitch Tear Strength of Leather, Double Hole has been revised to D4705-13 developed by Committee D31.07, ASTM BOS Volume 15.04.
  • D4761 Standard Test Methods for Mechanical Properties of Lumber and Wood-Base Structural Material has been revised to D4761-13 developed by Committee D07.01, ASTM BOS Volume 04.10.
  • D4806 Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel has been revised to D4806-13 developed by Committee D02.A0.02, ASTM BOS Volume 05.02.
  • D4809 Standard Test Method for Heat of Combustion of Liquid Hydrocarbon Fuels by Bomb Calorimeter (Precision Method) has been revised to D4809-13 developed by Committee D02.05, ASTM BOS Volume 05.02.
  • D4814 Standard Specification for Automotive Spark-Ignition Engine Fuel has been revised to D4814-13 developed by Committee D02.A0.01, ASTM BOS Volume 05.02.
  • D4890 Standard Test Methods for Polyurethane Raw Materials: Determination of Gardner and APHA Color of Polyols has been revised to D4890-13 developed by Committee D20.22, ASTM BOS Volume 08.03.
  • D4891 Standard Test Method for Heating Value of Gases in Natural Gas and Flare Gases Range by Stoichiometric Combustion has been revised (with title change) to D4891-13 developed by Committee D03.03, ASTM BOS Volume 05.06.
  • D4990 Standard Specification for Coal Tar Glass Felt Used in Roofing and Waterproofing has been reapproved, available as D4990-97a(2013) developed by Committee D08.04, ASTM BOS Volume 04.04.
  • D5007 Standard Test Method for Wet-to-Dry Hiding Change has been reapproved, available as D5007-99(2013) developed by Committee D01.42, ASTM BOS Volume 06.02.
  • D5124 Standard Practice for Testing and Use of a Random Number Generator in Lumber and Wood Products Simulation has been reapproved, available as D5124-96(2013) developed by Committee D07.05, ASTM BOS Volume 04.10.
  • D5178 Standard Test Method for Mar Resistance of Organic Coatings has been revised to D5178-13 developed by Committee D01.23, ASTM BOS Volume 06.01.
  • D5232 Standard Test Method for Determining the Stability and Miscibility of a Solid, Semi-Solid, or Liquid Waste Material has been revised to D5232-13 developed by Committee D34.01.06, ASTM BOS Volume 11.04.
  • D5236 Standard Test Method for Distillation of Heavy Hydrocarbon Mixtures (Vacuum Potstill Method) has been revised to D5236-13 developed by Committee D02.08, ASTM BOS Volume 05.02.
  • D5340 Standard Test Method for Airport Pavement Condition Index Surveys has been revised to D5340-12 developed by Committee E17.42, ASTM BOS Volume 04.03.
  • D5368 Standard Test Methods for Gravimetric Determination of Total Solvent Extractable Content (TSEC) of Solid Waste Samples has been revised to D5368-13 developed by Committee D34.01.06, ASTM BOS Volume 11.04.
  • D5404/D5404M Standard Practice for Recovery of Asphalt from Solution Using the Rotary Evaporator has been revised to D5404/D5404M-12 developed by Committee D04.25, ASTM BOS Volume 04.03.
  • D5652 Standard Test Methods for Bolted Connections in Wood and Wood-Based Products has been reapproved, available as D5652-95(2013) developed by Committee D07.05, ASTM BOS Volume 04.10.
  • D5658 Standard Practice for Sampling Unconsolidated Waste From Trucks has been revised to D5658-13 developed by Committee D34.01.02, ASTM BOS Volume 11.04.
  • D5704 Standard Test Method for Evaluation of the Thermal and Oxidative Stability of Lubricating Oils Used for Manual Transmissions and Final Drive Axles has been revised to D5704-13 developed by Committee D02.B0.03, ASTM BOS Volume 05.02.
  • D5719 Standard Guide for Simulation of Subsurface Airflow Using Groundwater Flow Modeling Codes has been revised to D5719-13 developed by Committee D18.21, ASTM BOS Volume 04.08.
  • D5721 Standard Practice for Air-Oven Aging of Polyolefin Geomembranes has been reapproved, available as D5721-08(2013) developed by Committee D35.02, ASTM BOS Volume 04.13.
  • D5726 Standard Specification for Thermoplastic Fabrics Used in Hot-Applied Roofing and Waterproofing has been reapproved, available as D5726-98(2013) developed by Committee D08.04, ASTM BOS Volume 04.04.
  • D5743 Standard Practice for Sampling Single or Multilayered Liquids, With or Without Solids, in Drums or Similar Containers has been reapproved, available as D5743-97(2013) developed by Committee D34.01.02, ASTM BOS Volume 11.04.
  • D5764 Standard Test Method for Evaluating Dowel-Bearing Strength of Wood and Wood-Based Products has been reapproved, available as D5764-97(2013) developed by Committee D07.05, ASTM BOS Volume 04.10.
  • D5785 Standard Test Method for (Analytical Procedure) for Determining Transmissivity of Confined Nonleaky Aquifers by Underdamped Well Response to Instantaneous Change in Head (Slug Test) has been reapproved, available as D5785-95(2013) developed by Committee D18.21, ASTM BOS Volume 04.08.
  • D5801 Standard Test Method for Toughness and Tenacity of Bituminous Materials has been revised to D5801-12 developed by Committee D04.44, ASTM BOS Volume 04.03.
  • D5855 Standard Test Method for (Analytical Procedure) for Determining Transmissivity and Storage Coefficient of Confined Nonleaky or Leaky Aquifer by Constant Drawdown Method in Flowing Well has been reapproved, available as D5855-95(2013) developed by Committee D18.21, ASTM BOS Volume 04.08.
  • D5869 Standard Practice for Dark Oven Heat Exposure of Roofing and Waterproofing Materials has been reapproved, available as D5869-07(2013) developed by Committee D08.02, ASTM BOS Volume 04.04.
  • D5898/D5898M Standard Guide for Standard Details for Adhered Sheet Waterproofing has been reapproved, available as D5898/D5898M-96(2013) developed by Committee D08.22, ASTM BOS Volume 04.04.
  • D5933 Standard Specification for 258-in. and 4-in. Diameter Metal Shear Plates for Use in Wood Constructions has been reapproved, available as D5933-96(2013) developed by Committee D07.05, ASTM BOS Volume 04.10.
  • D5957 Standard Guide for Flood Testing Horizontal Waterproofing Installations has been reapproved, available as D5957-98(2013) developed by Committee D08.22, ASTM BOS Volume 04.04.
  • D5966 Standard Test Method for Evaluation of Engine Oils for Roller Follower Wear in Light-Duty Diesel Engine has been revised to D5966-13 developed by Committee D02.B0.02, ASTM BOS Volume 05.02.
  • D5967 Standard Test Method for Evaluation of Diesel Engine Oils in T-8 Diesel Engine has been revised to D5967-13 developed by Committee D02.B0.02, ASTM BOS Volume 05.02.
  • D6075 Standard Test Method for Cracking Resistance of Leather has been revised to D6075-13 developed by Committee D31.01, ASTM BOS Volume 15.04.
  • D6134 Standard Specification for Vulcanized Rubber Sheets Used in Waterproofing Systems has been reapproved, available as D6134-07(2013) developed by Committee D08.18, ASTM BOS Volume 04.04.
  • D6138 Standard Test Method for Determination of Corrosion-Preventive Properties of Lubricating Greases Under Dynamic Wet Conditions (Emcor Test) has been revised to D6138-13 developed by Committee D02.G0.06, ASTM BOS Volume 05.03.
  • D6457 Standard Specification for Extruded and Compression Molded Rod and Heavy-Walled Tubing Made from Polytetrafluoroethylene (PTFE) has been reapproved, available as D6457-08(2013) developed by Committee D20.15, ASTM BOS Volume 08.03.
  • D6557 Standard Test Method for Evaluation of Rust Preventive Characteristics of Automotive Engine Oils has been revised to D6557-13 developed by Committee D02.B0.01, ASTM BOS Volume 05.03.
  • D6584 Standard Test Method for Determination of Total Monoglycerides, Total Diglycerides, Total Triglycerides, and Free and Total Glycerin in B-100 Biodiesel Methyl Esters by Gas Chromatography has been revised to D6584-13 developed by Committee D02.04.0L, ASTM BOS Volume 05.03.
  • D6593 Standard Test Method for Evaluation of Automotive Engine Oils for Inhibition of Deposit Formation in a Spark-Ignition Internal Combustion Engine Fueled with Gasoline and Operated Under Low-Temperature, Light-Duty Conditions has been revised to D6593-13 developed by Committee D02.B0.01, ASTM BOS Volume 05.03.
  • D6594 Standard Test Method for Evaluation of Corrosiveness of Diesel Engine Oil at 135 °C has been revised to D6594-13 developed by Committee D02.B0.02, ASTM BOS Volume 05.03.
  • D6658 Standard Test Method for Volatile Matter (Moisture) of Wet Blue by Oven Drying has been reapproved, available as D6658-08(2013) developed by Committee D31.02, ASTM BOS Volume 15.04.
  • D6681 Standard Test Method for Evaluation of Engine Oils in a High Speed, Single-Cylinder Diesel Engine—Caterpillar 1P Test Procedure has been revised to D6681-13 developed by Committee D02.B0.02, ASTM BOS Volume 05.03.
  • D6709 Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence VIII Spark-Ignition Engine (CLR Oil Test Engine) has been revised to D6709-13 developed by Committee D02.B0.01, ASTM BOS Volume 05.03.
  • D6716 Standard Test Method for Total Ash in Wet Blue or Wet White has been reapproved, available as D6716-08(2013) developed by Committee D31.02, ASTM BOS Volume 15.04.
  • D6782 Standard Test Methods for Standardization and Calibration of In-Line Dry Lumber Moisture Meters has been revised to D6782-13 developed by Committee D07.01, ASTM BOS Volume 04.10.
  • D6794 Standard Test Method for Measuring the Effect on Filterability of Engine Oils After Treatment with Various Amounts of Water and a Long (6 h) Heating Time has been revised to D6794-13 developed by Committee D02.B0, ASTM BOS Volume 05.03.
  • D6795 Standard Test Method for Measuring the Effect on Filterability of Engine Oils After Treatment with Water and Dry Ice and a Short (30 min) Heating Time has been revised to D6795-13 developed by Committee D02.B0, ASTM BOS Volume 05.03.
  • D6810 Standard Test Method for Measurement of Hindered Phenolic Antioxidant Content in Non-Zinc Turbine Oils by Linear Sweep Voltammetry has been revised to D6810-13 developed by Committee D02.09.0C, ASTM BOS Volume 05.03.
  • D6811 Standard Test Method for Measurement of Thermal Stability of Aviation Turbine Fuels under Turbulent Flow Conditions (HiReTS Method) (Withdrawn 2013) has been withdrawn, with no replacement. D6811-02(2007)e1 developed by Committee D02.14, ASTM BOS Volume 05.03.
  • D6817/D6817M Standard Specification for Rigid Cellular Polystyrene Geofoam has been revised (with designation change) to D6817/D6817M-13a developed by Committee D35.03, ASTM BOS Volume 04.13.
  • D6837 Standard Test Method for Measurement of Effects of Automotive Engine Oils on Fuel Economy of Passenger Cars and Light-Duty Trucks in Sequence VIB Spark Ignition Engine has been revised to D6837-13 developed by Committee D02.B0.01, ASTM BOS Volume 05.03.
  • D6890 Standard Test Method for Determination of Ignition Delay and Derived Cetane Number (DCN) of Diesel Fuel Oils by Combustion in a Constant Volume Chamber has been revised to D6890-13a developed by Committee D02.01, ASTM BOS Volume 05.05.
  • D6891 Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence IVA Spark-Ignition Engine has been revised to D6891-13 developed by Committee D02.B0, ASTM BOS Volume 05.03.
  • D6894 Standard Test Method for Evaluation of Aeration Resistance of Engine Oils in Direct-Injected Turbocharged Automotive Diesel Engine has been revised to D6894-13 developed by Committee D02.B0.02, ASTM BOS Volume 05.03.
  • D6922 Standard Test Method for Determination of Homogeneity and Miscibility in Automotive Engine Oils has been revised to D6922-13 developed by Committee D02.B0, ASTM BOS Volume 05.03.
  • D6923 Standard Test Method for Evaluation of Engine Oils in a High Speed, Single-Cylinder Diesel Engine—Caterpillar 1R Test Procedure has been revised to D6923-13 developed by Committee D02.B0, ASTM BOS Volume 05.03.
  • D6947 Standard Specification for Liquid Applied Moisture Cured Polyurethane Coating Used in Spray Polyurethane Foam Roofing System has been reapproved, available as D6947-07(2013) developed by Committee D08.06, ASTM BOS Volume 04.04.
  • D6976 Standard Specification for Rubber Contraceptives—Vaginal Diaphragms has been revised to D6976-13 developed by Committee D11.40, ASTM BOS Volume 09.02.
  • D6987/D6987M Standard Test Method for Evaluation of Diesel Engine Oils in T-10 Exhaust Gas Recirculation Diesel Engine has been revised to D6987/D6987M-13 developed by Committee D02.B0, ASTM BOS Volume 05.04.
  • D7006 Standard Practice for Ultrasonic Testing of Geomembranes has been reapproved, available as D7006-03(2013) developed by Committee D35.10, ASTM BOS Volume 04.13.
  • D7038 Standard Test Method for Evaluation of Moisture Corrosion Resistance of Automotive Gear Lubricants has been revised to D7038-13 developed by Committee D02.B0, ASTM BOS Volume 05.04.
  • D7051 Standard Test Method for Cyclic Thermal Shock of SBS-Modified Bituminous Roofing Sheets with Factory-Applied Metal Surface has been reapproved, available as D7051-05(2013) developed by Committee D08.04, ASTM BOS Volume 04.04.
  • D7103 Standard Guide for Assessment of Medical Gloves has been reapproved, available as D7103-06(2013) developed by Committee D11.40, ASTM BOS Volume 09.02.
  • D7105 Standard Test Method for Determining the Adhesive and Cohesive Strength Between Materials in Roofing or Waterproofing Membranes and Systems has been reapproved, available as D7105-06(2013) developed by Committee D08.20, ASTM BOS Volume 04.04.
  • D7127 Standard Test Method for Measurement of Surface Roughness of Abrasive Blast Cleaned Metal Surfaces Using a Portable Stylus Instrument has been revised to D7127-13 developed by Committee D01.46, ASTM BOS Volume 06.02.
  • D7156 Standard Test Method for Evaluation of Diesel Engine Oils in the T-11 Exhaust Gas Recirculation Diesel Engine has been revised to D7156-13 developed by Committee D02.B0, ASTM BOS Volume 05.04.
  • D7211 Standard Specification for Parts Machined from Polychlorotrifluoroethylene (PCTFE) and Intended for General Use has been revised to D7211-13 developed by Committee D20.15, ASTM BOS Volume 08.03.
  • D7261 Standard Test Method for Determining Water Separation Characteristics of Diesel Fuels by Portable Separometer has been revised to D7261-13 developed by Committee D02.14, ASTM BOS Volume 05.04.
  • D7281 Standard Test Method for Determining Water Migration Resistance Through Roof Membranes has been reapproved, available as D7281-07(2013) developed by Committee D08.20, ASTM BOS Volume 04.04.
  • D7283 Standard Test Method for Alpha and Beta Activity in Water By Liquid Scintillation Counting has been revised (with title change) to D7283-13 developed by Committee D19.04, ASTM BOS Volume 11.02.
  • D7323 Standard Practice for Handling, Transportation, and Storage of IG-100 (Nitrogen) has been revised to D7323-13 developed by Committee D26.09, ASTM BOS Volume 15.05.
  • D7324 Standard Practice for Handling, Transportation, and Storage of IG-55 Ar N2 has been revised to D7324-13 developed by Committee D26.09, ASTM BOS Volume 15.05.
  • D7325 Standard Practice for Handling, Transportation, and Storage of IG-541 N2, Ar , CO2 has been revised to D7325-13 developed by Committee D26.09, ASTM BOS Volume 15.05.
  • D7363 Standard Test Method for Determination of Parent and Alkyl Polycyclic Aromatics in Sediment Pore Water Using Solid-Phase Microextraction and Gas Chromatography/Mass Spectrometry in Selected Ion Monitoring Mode has been revised to D7363-13 developed by Committee D19.06, ASTM BOS Volume 11.02.
  • D7381 Standard Practice for Establishing Allowable Stresses for Round Timbers for Piles from Tests of Full-Size Material has been reapproved, available as D7381-07(2013) developed by Committee D07.04, ASTM BOS Volume 04.10.
  • D7438 Standard Practice for Field Calibration and Application of Hand-Held Moisture Meters has been revised to D7438-13 developed by Committee D07.01, ASTM BOS Volume 04.10.
  • D7450 Standard Specification for Performance of Rear Axle Gear Lubricants Intended for API Category GL-5 Service has been revised to D7450-13 developed by Committee D02.B0, ASTM BOS Volume 05.04.
  • D7467 Standard Specification for Diesel Fuel Oil, Biodiesel Blend (B6 to B20) has been revised to D7467-13 developed by Committee D02.E0, ASTM BOS Volume 05.04.
  • D7468 Standard Test Method for Cummins ISM Test has been revised to D7468-13 developed by Committee D02.B0, ASTM BOS Volume 05.04.
  • D7484 Standard Test Method for Evaluation of Automotive Engine Oils for Valve-Train Wear Performance in Cummins ISB Medium-Duty Diesel Engine has been revised to D7484-13 developed by Committee D02.B0, ASTM BOS Volume 05.04.
  • D7589 Standard Test Method for Measurement of Effects of Automotive Engine Oils on Fuel Economy of Passenger Cars and Light-Duty Trucks in Sequence VID Spark Ignition Engine has been revised to D7589-13 developed by Committee D02.B0.10, ASTM BOS Volume 05.04.
  • D7600 Standard Test Method for Determination of Aldicarb, Carbofuran, Oxamyl and Methomyl by Liquid Chromatography/Tandem Mass Spectrometry has been editorially changed, available as D7600-09e2 developed by Committee D19.06, ASTM BOS Volume 11.02.
  • D7672 Standard Specification for Evaluating Structural Capacities of Rim Board Products and Assemblies has been revised to D7672-13 developed by Committee D07.05, ASTM BOS Volume 04.10.
  • D7748/D7748M Standard Test Method for Flexural Rigidity of Geogrids, Geotextiles and Related Products has been revised (with designation change) to D7748/D7748M-13 developed by Committee D35.01, ASTM BOS Volume 04.13.
  • D7777 Standard Test Method for Density, Relative Density, or API Gravity of Liquid Petroleum by Portable Digital Density Meter has been revised to D7777-13 developed by Committee D02.04.0D, ASTM BOS Volume 05.04.
  • D7822 Standard Practice for Dermal Wipe Sampling for the Subsequent Determination of Metals and Metalloids is a new standard, now available. D7822-13 developed by Committee D22.04, ASTM BOS Volume 11.07.
  • D7823 Standard Test Method for Determination of Low Level, Regulated Phthalates in Poly (Vinyl Chloride) Plastics by Thermal Desorption—Gas Chromatography/Mass Chromatography is a new standard, now available. D7823-13 developed by Committee D20.70, ASTM BOS Volume 08.03.
  • D7831 Standard Practice for Sampling of Tanks by Field Personnel is a new standard, now available. D7831-13 developed by Committee D34.01.02, ASTM BOS Volume 11.04.
  • D7845 Standard Test Method for Determination of Chemical Species in Marine Fuel Oil by Multidimensional Gas Chromatography – Mass Spectrometry is a new standard, now available. D7845-13 developed by Committee D02.04.0M, ASTM BOS Volume 05.04.
  • D7858 Standard Test Method for Determination of Bisphenol A in Soil, Sludge and Biosolids by Pressurized Fluid Extraction and Analyzed by Liquid Chromatography/Tandem Mass Spectrometry is a new standard, now available. D7858-13 developed by Committee D34.01.06, ASTM BOS Volume 11.04.
  • D7859 Standard Practice for Spraying, Sampling, Packaging, and Test Specimen Preparation of Spray Polyurethane Foam (SPF) Insulation for Testing of Emissions Using Environmental Chambers has been editorially changed, available as D7859-13e1 developed by Committee D22.05, ASTM BOS Volume 11.07.
  • E4 Standard Practices for Force Verification of Testing Machines has been revised to E4-13 developed by Committee E28.01, ASTM BOS Volume 03.01.
  • E45 Standard Test Methods for Determining the Inclusion Content of Steel has been revised to E45-13 developed by Committee E04.09, ASTM BOS Volume 03.01.
  • E74 Standard Practice of Calibration of Force-Measuring Instruments for Verifying the Force Indication of Testing Machines has been revised to E74-13a developed by Committee E28.01, ASTM BOS Volume 03.01.
  • E140 Standard Hardness Conversion Tables for Metals Relationship Among Brinell Hardness, Vickers Hardness, Rockwell Hardness, Superficial Hardness, Knoop Hardness, Scleroscope Hardness, and Leeb Hardness has been revised to E140-12b developed by Committee E28.06, ASTM BOS Volume 03.01.
  • E154/E154M Standard Test Methods for Water Vapor Retarders Used in Contact with Earth Under Concrete Slabs, on Walls, or as Ground Cover has been revised (with designation change) to E154/E154M-08a(2013)e1 developed by Committee E06.21, ASTM BOS Volume 04.11.
  • E176 Standard Terminology of Fire Standards has been revised to E176-13 developed by Committee E05.31, ASTM BOS Volume 04.07.
  • E177 Standard Practice for Use of the Terms Precision and Bias in ASTM Test Methods has been revised to E177-13 developed by Committee E11.20, ASTM BOS Volume 14.02.
  • E253 Standard Terminology Relating to Sensory Evaluation of Materials and Products has been revised to E253-13 developed by Committee E18.01, ASTM BOS Volume 15.08.
  • E351 Standard Test Methods for Chemical Analysis of Cast Iron—All Types has been revised to E351-13 developed by Committee E01.01, ASTM BOS Volume 03.05.
  • E352 Standard Test Methods for Chemical Analysis of Tool Steels and Other Similar Medium- and High-Alloy Steels has been revised to E352-13 developed by Committee E01.01, ASTM BOS Volume 03.05.
  • E399 Standard Test Method for Linear-Elastic Plane-Strain Fracture Toughness KIc of Metallic Materials has been editorially changed, available as E399-12e1 developed by Committee E08.07, ASTM BOS Volume 03.01.
  • E452 Standard Test Method for Calibration of Refractory Metal Thermocouples Using a Radiation Thermometer has been reapproved, available as E452-02(2013) developed by Committee E20.04, ASTM BOS Volume 14.03.
  • E456 Standard Terminology Relating to Quality and Statistics has been editorially changed, available as E456-12e1 developed by Committee E11.70, ASTM BOS Volume 14.02.
  • E578 Standard Test Method for Linearity of Fluorescence Measuring Systems has been reapproved, available as E578-07(2013) developed by Committee E13.01, ASTM BOS Volume 03.06.
  • E601 Standard Test Method for Measuring Electromotive Force (emf) Stability of Base-Metal Thermoelement Materials with Time in Air has been reapproved, available as E601-07(2013) developed by Committee E20.04, ASTM BOS Volume 14.03.
  • E645 Standard Practice for Evaluation of Microbicides Used in Cooling Water Systems has been revised (with title change) to E645-13 developed by Committee E35.15, ASTM BOS Volume 11.05.
  • E647 Standard Test Method for Measurement of Fatigue Crack Growth Rates has been editorially changed, available as E647-13e1 developed by Committee E08.06, ASTM BOS Volume 03.01.
  • E691 Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method has been revised to E691-13 developed by Committee E11.20, ASTM BOS Volume 14.02.
  • E696 Standard Specification for Tungsten-Rhenium Alloy Thermocouple Wire has been reapproved, available as E696-07(2013) developed by Committee E20.04, ASTM BOS Volume 14.03.
  • E723 Standard Practice for Evaluation of Antimicrobials as Preservatives for Aqueous-Based Products Used in the Paper Industry (Bacterial Spoilage) has been revised (with title change) to E723-13 developed by Committee E35.15, ASTM BOS Volume 11.05.
  • E740/E740M Standard Practice for Fracture Testing with Surface-Crack Tension Specimens has been editorially changed, available as E740/E740M-03(2010)e2 developed by Committee E08.07, ASTM BOS Volume 03.01.
  • E1054 Standard Test Methods for Evaluation of Inactivators of Antimicrobial Agents has been reapproved, available as E1054-08(2013) developed by Committee E35.15, ASTM BOS Volume 11.05.
  • E1142 Standard Terminology Relating to Thermophysical Properties has been revised to E1142-13 developed by Committee E37.03, ASTM BOS Volume 14.02.
  • E1169 Standard Practice for Conducting Ruggedness Tests has been revised to E1169-13 developed by Committee E11.20, ASTM BOS Volume 14.02.
  • E1170 Standard Practices for Simulating Vehicular Response to Longitudinal Profiles of Traveled Surfaces has been reapproved, available as E1170-97(2012) developed by Committee E17.33, ASTM BOS Volume 04.03.
  • E1221 Standard Test Method for Determining Plane-Strain Crack-Arrest Fracture Toughness, KIa, of Ferritic Steels has been revised to E1221-12a developed by Committee E08.07, ASTM BOS Volume 03.01.
  • E1354 Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter has been revised to E1354-13 developed by Committee E05.21, ASTM BOS Volume 04.07.
  • E1434 Standard Guide for Recording Mechanical Test Data of Fiber-Reinforced Composite Materials in Databases has been reapproved, available as E1434-00(2013) developed by Committee D30.01, ASTM BOS Volume 15.03.
  • E1457 Standard Test Method for Measurement of Creep Crack Growth Times and Rates in Metals has been revised to E1457-13 developed by Committee E08.06, ASTM BOS Volume 03.01.
  • E1477 Standard Test Method for Luminous Reflectance Factor of Acoustical Materials by Use of Integrating-Sphere Reflectometers has been reapproved, available as E1477-98a(2013) developed by Committee E12.02, ASTM BOS Volume 06.01.
  • E1517 Standard Test Method for Determining the Effectiveness of Liquid, Gel, Cream, or Shampoo Insecticides Against Human Louse Ova has been revised to E1517-13 developed by Committee E35.12, ASTM BOS Volume 11.05.
  • E1537 Standard Test Method for Fire Testing of Upholstered Furniture has been revised to E1537-13 developed by Committee E05.15, ASTM BOS Volume 04.07.
  • E1554/E1554M Standard Test Methods for Determining Air Leakage of Air Distribution Systems by Fan Pressurization has been revised (with designation change) to E1554/E1554M-13 developed by Committee E06.41, ASTM BOS Volume 04.11.
  • E1590 Standard Test Method for Fire Testing of Mattresses has been revised to E1590-13 developed by Committee E05.15, ASTM BOS Volume 04.07.
  • E1591 Standard Guide for Obtaining Data for Fire Growth Models has been revised to E1591-13 developed by Committee E05.33, ASTM BOS Volume 04.07.
  • E1593 Standard Guide for Assessing the Efficacy of Air Care Products in Reducing the Perception of Indoor Malodor has been revised (with title change) to E1593-13 developed by Committee E18.07, ASTM BOS Volume 15.08.
  • E1600 Standard Test Method for Determination of Gold in Cyanide Solutions by Flame Atomic Absorption Spectrometry has been revised to E1600-13 developed by Committee E01.02, ASTM BOS Volume 03.05.
  • E1822 Standard Test Method for Fire Testing of Stacked Chairs has been revised to E1822-13 developed by Committee E05.15, ASTM BOS Volume 04.07.
  • E1823 Standard Terminology Relating to Fatigue and Fracture Testing has been revised to E1823-13 developed by Committee E08.02, ASTM BOS Volume 03.01.
  • E1839 Standard Test Method for Efficacy of Slimicides for the Paper Industry—Bacterial and Fungal Slime has been revised to E1839-13 developed by Committee E35.15, ASTM BOS Volume 11.05.
  • E1849 Standard Guide for Fish and Wildlife Incident Monitoring and Reporting has been reapproved, available as E1849-96(2013) developed by Committee E50.47, ASTM BOS Volume 11.06.
  • E1867 Standard Test Method for Temperature Calibration of Dynamic Mechanical Analyzers has been revised to E1867-13 developed by Committee E37.10, ASTM BOS Volume 14.02.
  • E1993 Standard Specification for Bituminous Water Vapor Retarders Used in Contact with Soil or Granular Fill Under Concrete Slabs has been revised (with designation change) to E1993/E1993M-98(2013)e1 developed by Committee E06.21, ASTM BOS Volume 04.11.
  • E2011 Standard Test Method for Evaluation of Hygienic Handwash and Handrub Formulations for Virus-Eliminating Activity Using the Entire Hand has been revised to E2011-13 developed by Committee E35.15, ASTM BOS Volume 11.05.
  • E2102 Standard Test Method for Measurement of Mass Loss and Ignitability for Screening Purposes Using a Conical Radiant Heater has been revised to E2102-13 developed by Committee E05.21, ASTM BOS Volume 04.07.
  • E2103/E2103M Standard Classification for Bridge Elements—UNIFORMAT II has been revised (with designation change) to E2103/E2103M-13 developed by Committee E06.81, ASTM BOS Volume 04.11.
  • E2230 Standard Practice for Thermal Qualification of Type B Packages for Radioactive Material has been revised to E2230-13 developed by Committee E05.17, ASTM BOS Volume 04.07.
  • E2257 Standard Test Method for Room Fire Test of Wall and Ceiling Materials and Assemblies has been revised to E2257-13 developed by Committee E05.21, ASTM BOS Volume 04.07.
  • E2404 Standard Practice for Specimen Preparation and Mounting of Textile, Paper or Polymeric (Including Vinyl) Wall or Ceiling Coverings, and of Facings and Wood Veneers Intended to be Applied on Site Over a Wood Substrate, to Assess Surface Burning Charact has been editorially changed, available as E2404-13e1 developed by Committee E05.22, ASTM BOS Volume 04.07.
  • E2455 Standard Guide for Conducting Laboratory Toxicity Tests with Freshwater Mussels has been reapproved, available as E2455-06(2013) developed by Committee E50.47, ASTM BOS Volume 11.06.
  • E2551 Standard Test Method for Humidity Calibration (or Conformation) of Humidity Generators for Use with Thermogravimetric Analyzers has been revised to E2551-13 developed by Committee E37.10, ASTM BOS Volume 14.02.
  • E2554 Standard Practice for Estimating and Monitoring the Uncertainty of Test Results of a Test Method Using Control Chart Techniques has been revised (with title change) to E2554-13 developed by Committee E11.20, ASTM BOS Volume 14.02.
  • E2579 Standard Practice for Specimen Preparation and Mounting of Wood Products to Assess Surface Burning Characteristics has been revised to E2579-13 developed by Committee E05.22, ASTM BOS Volume 04.07.
  • E2647 Standard Test Method for Quantification of Pseudomonas aeruginosa Biofilm Grown Using Drip Flow Biofilm Reactor with Low Shear and Continuous Flow has been revised to E2647-13 developed by Committee E35.15, ASTM BOS Volume 11.05.
  • E2772 Standard Specification for Evaluation and Selection of Accommodations for Environmentally Sustainable Meetings, Events, Trade Shows, and Conferences has been editorially changed, available as E2772-13e1 developed by Committee E60.02, ASTM BOS Volume 04.12.
  • E2810 Standard Practice for Demonstrating Capability to Comply with the Test for Uniformity of Dosage Units has been editorially changed, available as E2810-11e1 developed by Committee E55.03, ASTM BOS Volume 14.02.
  • E2856 Standard Guide for Estimation of LNAPL Transmissivity has been revised to E2856-13 developed by Committee E50.04, ASTM BOS Volume 11.05.
  • E2870 Standard Test Method for Evaluating Relative Effectiveness of Antimicrobial Handwashing Formulations using the Palmar Surface and Mechanical Hand Sampling is a new standard, now available. E2870-13 developed by Committee E35.15, ASTM BOS Volume 11.05.
  • F15 Standard Specification for Iron-Nickel-Cobalt Sealing Alloy has been reapproved, available as F15-04(2013) developed by Committee F01.03, ASTM BOS Volume 10.04.
  • F37 Standard Test Methods for Sealability of Gasket Materials has been reapproved, available as F37-06(2013) developed by Committee F03.10, ASTM BOS Volume 09.02.
  • F73 Standard Specification for Tungsten-Rhenium Alloy Wire for Electron Devices and Lamps has been reapproved, available as F73-96(2013) developed by Committee F01.03, ASTM BOS Volume 10.04.
  • F83 Standard Practice for Definition and Determination of Thermionic Constants of Electron Emitters has been reapproved, available as F83-71(2013) developed by Committee F01.03, ASTM BOS Volume 10.04.
  • F85 Standard Practice for Nomenclature for Wire Leads Used as Conductors in Electron Tubes has been reapproved, available as F85-76(2013) developed by Committee F01.03, ASTM BOS Volume 10.04.
  • F112 Standard Test Method for Sealability of Enveloped Gaskets has been reapproved, available as F112-00(2013) developed by Committee F03.10, ASTM BOS Volume 09.02.
  • F148 Standard Test Method for Binder Durability of Cork Composition Gasket Materials has been reapproved, available as F148-02(2013) developed by Committee F03.40, ASTM BOS Volume 09.02.
  • F204 Standard Test Method for Surface Flaws in Tungsten Seal Rod and Wire has been reapproved, available as F204-76(2013) developed by Committee F01.03, ASTM BOS Volume 10.04.
  • F219 Standard Test Methods of Testing Fine Round and Flat Wire for Electron Devices and Lamps has been reapproved, available as F219-96(2013) developed by Committee F01.03, ASTM BOS Volume 10.04.
  • F373 Standard Test Method for Embossed Depth of Resilient Floor Coverings has been revised to F373-13 developed by Committee F06.20, ASTM BOS Volume 15.04.
  • F406 Standard Consumer Safety Specification for Non-Full-Size Baby Cribs/Play Yards has been revised to F406-13 developed by Committee F15.18, ASTM BOS Volume 15.11.
  • F430 Standard Specification for Paper Used for Vacuum Cleaner Filter Bags has been revised to F430-13 developed by Committee F11.23, ASTM BOS Volume 15.08.
  • F467 Standard Specification for Nonferrous Nuts for General Use has been revised to F467-13 developed by Committee F16.04, ASTM BOS Volume 01.08.
  • F615M Standard Practice for Determining Safe Current Pulse-Operating Regions for Metallization on Semiconductor Components (Metric) has been reapproved, available as F615M-95(2013) developed by Committee F01.11, ASTM BOS Volume 10.04.
  • F783 Standard Specification for Staple, Handgrab, Handle, and Stirrup Rung has been reapproved, available as F783-88(2013) developed by Committee F25.03, ASTM BOS Volume 01.07.
  • F842 Standard Test Methods for Measuring the Forced Entry Resistance of Sliding Door Assemblies, Excluding Glazing Impact has been revised to F842-13 developed by Committee E06.51, ASTM BOS Volume 04.12.
  • F876 Standard Specification for Crosslinked Polyethylene (PEX) Tubing has been revised to F876-13 developed by Committee F17.26, ASTM BOS Volume 08.04.
  • F887 Standard Specifications for Personal Climbing Equipment has been revised to F887-13 developed by Committee F18.15, ASTM BOS Volume 10.03.
  • F925 Standard Test Method for Resistance to Chemicals of Resilient Flooring has been revised to F925-13 developed by Committee F06.30, ASTM BOS Volume 15.04.
  • F1011 Standard Guide for Developing a Hazardous Materials Training Curriculum for Initial Response Personnel has been reapproved, available as F1011-07(2013) developed by Committee F20.21, ASTM BOS Volume 11.05.
  • F1127 Standard Guide for Containment of Hazardous Material Spills by Emergency Response Personnel has been reapproved, available as F1127-07(2013) developed by Committee F20.22, ASTM BOS Volume 11.05.
  • F1169 Standard Consumer Safety Specification for Full-Size Baby Cribs has been revised to F1169-13 developed by Committee F15.18, ASTM BOS Volume 15.11.
  • F1196 Standard Specification for Sliding Watertight Door Assemblies has been reapproved, available as F1196-00(2013) developed by Committee F25.03, ASTM BOS Volume 01.07.
  • F1244 Standard Specification for Berths, Marine has been reapproved, available as F1244-08(2013) developed by Committee F25.03, ASTM BOS Volume 01.07.
  • F1265 Standard Test Method for Resistance to Impact for Resilient Floor Tile has been reapproved, available as F1265-03a(2013) developed by Committee F06.30, ASTM BOS Volume 15.04.
  • F1344 Standard Specification for Rubber Floor Tile has been editorially changed, available as F1344-12e1 developed by Committee F06.80, ASTM BOS Volume 15.04.
  • F1514 Standard Test Method for Measuring Heat Stability of Resilient Flooring by Color Change has been reapproved, available as F1514-03(2013) developed by Committee F06.30, ASTM BOS Volume 15.04.
  • F1516 Standard Practice for Sealing Seams of Resilient Flooring Products by the Heat Weld Method (when Recommended) has been revised to F1516-13 developed by Committee F06.40, ASTM BOS Volume 15.04.
  • F1524 Standard Guide for Use of Advanced Oxidation Process for the Mitigation of Chemical Spills has been reapproved, available as F1524-95(2013) developed by Committee F20.22, ASTM BOS Volume 11.05.
  • F1564 Standard Specification for Structure-Mounted Insulating Work Platforms for Electrical Workers has been revised to F1564-13 developed by Committee F18.35, ASTM BOS Volume 10.03.
  • F1565 Standard Specification for Pressure-Reducing Valves for Steam Service has been reapproved, available as F1565-00(2013) developed by Committee F25.11, ASTM BOS Volume 01.07.
  • F1567 Standard Specification for Fabricated or Cast Automatic Self-Cleaning, Fuel Oil and Lubricating Oil Strainers has been reapproved, available as F1567-94(2013) developed by Committee F25.11, ASTM BOS Volume 01.07.
  • F1600 Standard Terminology Relating to Bioremediation has been reapproved, available as F1600-95(2013) developed by Committee F20.24, ASTM BOS Volume 11.05.
  • F1685 Standard Specification for Pressure-Reducing Manifolds for Air or Nitrogen Systems has been reapproved, available as F1685-00(2013) developed by Committee F25.11, ASTM BOS Volume 01.07.
  • F1693 Standard Guide for Consideration of Bioremediation as an Oil Spill Response Method on Land has been reinstated, with revision to F1693-13 developed by Committee F20.13, ASTM BOS Volume 11.05.
  • F1718 Standard Specification for Rotary Positive Displacement Distillate Fuel Pumps has been reapproved, available as F1718-01(2013) developed by Committee F25.11, ASTM BOS Volume 01.07.
  • F1733 Standard Specification for Butt Heat Fusion Polyamide(PA) Plastic Fitting for Polyamide(PA) Plastic Pipe and Tubing has been revised to F1733-13 developed by Committee F17.10, ASTM BOS Volume 08.04.
  • F1791 Standard Specification for Filters Used in Air or Nitrogen Systems has been reapproved, available as F1791-00(2013) developed by Committee F25.11, ASTM BOS Volume 01.07.
  • F1795 Standard Specification for Pressure-Reducing Valves for Air or Nitrogen Systems has been reapproved, available as F1795-00(2013) developed by Committee F25.11, ASTM BOS Volume 01.07.
  • F1807 Standard Specification for Metal Insert Fittings Utilizing a Copper Crimp Ring for SDR9 Cross-linked Polyethylene (PEX) Tubing and SDR9 Polyethylene of Raised Temperature (PE-RT) Tubing has been revised to F1807-13 developed by Committee F17.10, ASTM BOS Volume 08.04.
  • F1883 Standard Practice for Selection of Wire and Cable Size in AWG or Metric Units has been reapproved, available as F1883-03(2013) developed by Committee F25.10, ASTM BOS Volume 01.07.
  • F1973 Standard Specification for Factory Assembled Anodeless Risers and Transition Fittings in Polyethylene (PE) and Polyamide 11 (PA11) and Polyamide 12 (PA12) Fuel Gas Distribution Systems has been revised to F1973-13 developed by Committee F17.60, ASTM BOS Volume 08.04.
  • F1995 Standard Test Method for Determining the Shear Strength of the Bond between a Surface Mount Device (SMD) and Substrate in a Membrane Switch has been revised (with title change) to F1995-13 developed by Committee F01.18, ASTM BOS Volume 10.04.
  • F2014 Standard Specification for Non-Reinforced Extruded Tee Connections for Piping Applications has been reapproved, available as F2014-00(2013) developed by Committee F25.11, ASTM BOS Volume 01.07.
  • F2015 Standard Specification for Lap Joint Flange Pipe End Applications has been reapproved, available as F2015-00(2013) developed by Committee F25.11, ASTM BOS Volume 01.07.
  • F2123 Standard Practice for Treestand Instructions has been revised to F2123-13 developed by Committee F08.16, ASTM BOS Volume 15.07.
  • F2128 Standard Test Method for Treestand Repetitive Loading Capability has been revised to F2128-13 developed by Committee F08.16, ASTM BOS Volume 15.07.
  • F2133 Standard Test Methods for Determining Effects of Large Hydrocarbon Pool Fires on Insulated Marine Bulkheads and Decks, Constructed of Steel (Withdrawn 2013) has been withdrawn, with no replacement. F2133- developed by Committee F25.02, ASTM BOS Volume 01.07.
  • F2145 Standard Specification for Polyamide 11 (PA 11) and Polyamide 12 (PA12) Mechanical Fittings for Use on Outside Diameter Controlled Polyamide 11 and Polyamide 12 Pipe and Tubing has been revised to F2145-13 developed by Committee F17.60, ASTM BOS Volume 08.04.
  • F2154 Standard Specification for Sound-Absorbing Board, Fibrous Glass, Perforated Fibrous Glass Cloth Faced has been revised to F2154-13 developed by Committee F25.02, ASTM BOS Volume 01.07.
  • F2164 Standard Practice for Field Leak Testing of Polyethylene (PE) and Crosslinked Polyethylene (PEX) Pressure Piping Systems Using Hydrostatic Pressure has been revised to F2164-13 developed by Committee F17.40, ASTM BOS Volume 08.04.
  • F2205 Standard Guide for Ecological Considerations for the Use of Chemical Dispersants in Oil Spill Response: Tropical Environments has been reapproved, available as F2205-07(2013) developed by Committee F20.13, ASTM BOS Volume 11.05.
  • F2246 Standard Specification for Bearing, Roller, Needle: Thick Outer Ring With Rollers and Cage has been reapproved, available as F2246-06(2013) developed by Committee F34.04, ASTM BOS Volume 01.08.
  • F2272 Standard Specification for Paintball Markers has been revised to F2272-13 developed by Committee F08.24, ASTM BOS Volume 15.07.
  • F2467 Standard Practice for Measuring Static Sealing Pressure Using Pressure-Indicating Film (PIF) in Transportation Applications has been reapproved, available as F2467-06(2013) developed by Committee F03.10, ASTM BOS Volume 09.02.
  • F2488 Standard Terminology for Rolling Element Bearings has been reapproved, available as F2488-05(2013) developed by Committee F34.91, ASTM BOS Volume 01.08.
  • F2511 Standard Specification for Rollers, Bearing, Needle, Ferrous, Solid has been reapproved, available as F2511-05(2013) developed by Committee F34.01, ASTM BOS Volume 01.08.
  • F2523 Standard Practice for Blowout Resistance of Room-Temperature Vulcanized Elastomers has been reapproved, available as F2523-07(2013) developed by Committee F03.70, ASTM BOS Volume 09.02.
  • F2524 Standard Practice for Determination of Volatile Content for Formed-in-Place Gaskets (FIPG) Silicone Adhesives and Sealants for Transportation Applications has been reapproved, available as F2524-06(2013) developed by Committee F03.50, ASTM BOS Volume 09.02.
  • F2590 Standard Specification for Bearing, Roller, Thrust, Two Channeled Race Surface, Rigid or Flat Seat Type has been reapproved, available as F2590-06(2013) developed by Committee F34.04, ASTM BOS Volume 01.08.
  • F2679 Standard Specification for 6 mm Projectiles Used with Low Energy Air Guns has been revised to F2679-13 developed by Committee F08.27, ASTM BOS Volume 15.07.
  • F2787 Standard Practice for Structural Design of Thermoplastic Corrugated Wall Stormwater Collection Chambers has been revised to F2787-13 developed by Committee F17.65, ASTM BOS Volume 08.04.
  • F2877 Standard Test Method for Shock Testing of Structural Insulation of A-Class Divisions Constructed of Steel or Aluminum has been revised to F2877-13 developed by Committee F25.02, ASTM BOS Volume 01.07.
  • F2907 - Consumer Safety Specification for Sling Carriers has been revised to F2907-13 developed by Committee F15.21, ASTM BOS Volume 15.11.
  • F2921 Standard Terminology for Additive Manufacturing—Coordinate Systems and Test Methodologies has been editorially changed, available as F2921-11e3 developed by Committee F42.01, ASTM BOS Volume 10.04.
  • F2933 Standard Consumer Safety Specification for Crib Mattresses is a new standard, now available. F2933-13 developed by Committee F15.66, ASTM BOS Volume 15.11.
  • F2943 Standard Guide for Presentation of End User Labeling Information for Orthopedic Implants Used in Joint Arthroplasty is a new standard, now available. F2943-13 developed by Committee F04.22, ASTM BOS Volume 13.02.
  • F2957 Standard Specification for Ornamental Aluminum Fence Systems is a new standard, now available. F2957-13 developed by Committee F14.35, ASTM BOS Volume 01.06.
  • F2993 Standard Guide for Monitoring Weather Conditions for Safe Parasail Operation is a new standard, now available. F2993-13 developed by Committee F24.65, ASTM BOS Volume 15.07.
  • F2999 Standard Consumer Safety Specification for Adult Jewelry is a new standard, now available. F2999-13 developed by Committee F15.24, ASTM BOS Volume 15.11.
  • G67 Standard Test Method for Determining the Susceptibility to Intergranular Corrosion of 5XXX Series Aluminum Alloys by Mass Loss After Exposure to Nitric Acid (NAMLT Test) has been reinstated as G67-13 developed by Committee G01.05, ASTM BOS Volume 03.02.
  • G150 Standard Test Method for Electrochemical Critical Pitting Temperature Testing of Stainless Steels has been revised to G150-13 developed by Committee G01.11, ASTM BOS Volume 03.02.
  • G180 Standard Test Method for Corrosion Inhibiting Admixtures for Steel in Concrete by Polarization Resistance in Cementitious Slurries has been revised (with title change) to G180-13 developed by Committee G01.14, ASTM BOS Volume 03.02.
  • G209 Standard Practice for Detecting mu-phase in Wrought Nickel-Rich, Chromium, Molybdenum-Bearing Alloys has been revised to G209-13 developed by Committee G01.05, ASTM BOS Volume 03.02.

Published in international.