ASTM standards

Set out below are recent publications from ASTM International. To purchase ASTM standards in hard copy or PDF format, please call 0800 782 632 during business hours or email enquiries@standards.co.nz 

  • A27/A27M - Standard Specification for Steel Castings, Carbon, for General Application has been revised to A27/A27M-13 developed by Committee A01.18, ASTM BOS Volume 01.02. 
  • A82/A82M - Standard Specification for Steel Wire, Plain, for Concrete Reinforcement has been withdrawn and replaced by A1064 developed by Committee A01.05, ASTM BOS Volume 01.04. 
  • A123/A123M - Standard Specification for Zinc (Hot-Dip Galvanized) Coatings on Iron and Steel Products has been revised to A123/A123M-13 developed by Committee A05.13, ASTM BOS Volume 01.06. 
  • A125 - Standard Specification for Steel Springs, Helical, Heat-Treated has been editorially changed, available as A125-96(2013)e1 developed by Committee A01.15, ASTM BOS Volume 01.05. 
  • A131/A131M - Standard Specification for Structural Steel for Ships has been revised to A131/A131M-13 developed by Committee A01.02, ASTM BOS Volume 01.04. 
  • A185/A185M - Standard Specification for Steel Welded Wire Reinforcement, Plain, for Concrete has been withdrawn and replaced by A1064 developed by Committee A01.05, ASTM BOS Volume 01.04. 
  • A240/A240M - Standard Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for General Applications has been revised to A240/A240M-13c developed by Committee A01.17, ASTM BOS Volume 01.03. 
  • A276 - Standard Specification for Stainless Steel Bars and Shapes has been revised to A276-13a developed by Committee A01.17, ASTM BOS Volume 01.03. 
  • A283/A283M - Standard Specification for Low and Intermediate Tensile Strength Carbon Steel Plates has been revised to A283/A283M-13 developed by Committee A01.02, ASTM BOS Volume 01.04. 
  • A473 - Standard Specification for Stainless Steel Forgings has been revised to A473-13 developed by Committee A01.17, ASTM BOS Volume 01.03. 
  • A479/A479M - Standard Specification for Stainless Steel Bars and Shapes for Use in Boilers and Other Pressure Vessels has been revised to A479/A479M-13b developed by Committee A01.17, ASTM BOS Volume 01.03. 
  • A480/A480M - Standard Specification for General Requirements for Flat-Rolled Stainless and Heat-Resisting Steel Plate, Sheet, and Strip has been revised to A480/A480M-13b developed by Committee A01.17, ASTM BOS Volume 01.03. 
  • A496/A496M - Standard Specification for Steel Wire, Deformed, for Concrete Reinforcement has been withdrawn and replaced by A1064 developed by Committee A01.05, ASTM BOS Volume 01.04. 
  • A497/A497M - Standard Specification for Steel Welded Wire Reinforcement, Deformed, for Concrete has been withdrawn and replaced by A1064 developed by Committee A01.05, ASTM BOS Volume 01.04. 
  • A573/A573M - Standard Specification for Structural Carbon Steel Plates of Improved Toughness has been revised to A573/A573M-13 developed by Committee A01.02, ASTM BOS Volume 01.04. 
  • A760/A760M - Standard Specification for Corrugated Steel Pipe, Metallic-Coated for Sewers and Drains has been revised to A760/A760M-13 developed by Committee A05.17, ASTM BOS Volume 01.06. 
  • A761/A761M - Standard Specification for Corrugated Steel Structural Plate, Zinc-Coated, for Field-Bolted Pipe, Pipe-Arches, and Arches has been revised to A761/A761M-13a developed by Committee A05.17, ASTM BOS Volume 01.06. 
  • A789/A789M - Standard Specification for Seamless and Welded Ferritic/Austenitic Stainless Steel Tubing for General Service has been editorially changed, available as A789/A789M-13ae1 developed by Committee A01.10, ASTM BOS Volume 01.01. 
  • A796/A796M - Standard Practice for Structural Design of Corrugated Steel Pipe, Pipe-Arches, and Arches for Storm and Sanitary Sewers and Other Buried Applications has been revised to A796/A796M-13a developed by Committee A05.17, ASTM BOS Volume 01.06. 
  • A807/A807M - Standard Practice for Installing Corrugated Steel Structural Plate Pipe for Sewers and Other Applications has been revised to A807/A807M-13 developed by Committee A05.17, ASTM BOS Volume 01.06. 
  • A841/A841M - Standard Specification for Steel Plates for Pressure Vessels, Produced by Thermo-Mechanical Control Process (TMCP) has been revised to A841/A841M-13 developed by Committee A01.11, ASTM BOS Volume 01.04. 
  • A902 - Standard Terminology Relating to Metallic Coated Steel Products has been revised to A902-13b developed by Committee A05.18, ASTM BOS Volume 01.06. 
  • A942/A942M - Standard Specification for Centrifugally Cast White Iron/Gray Iron Dual Metal Abrasion-Resistant Roll Shells has been editorially changed, available as A942/A942M-95(2012)e1 developed by Committee A04.01, ASTM BOS Volume 01.02. 
  • A976 - Standard Classification of Insulating Coatings for Electrical Steels by Composition, Relative Insulating Ability and Application has been revised to A976-13 developed by Committee A06.02, ASTM BOS Volume 03.04. 
  • A1003/A1003M - Standard Specification for Steel Sheet, Carbon, Metallic- and Nonmetallic-Coated for Cold-Formed Framing Members has been revised to A1003/A1003M-13b developed by Committee A05.11, ASTM BOS Volume 01.06. 
  • A1064/A1064M - Standard Specification for Carbon-Steel Wire and Welded Wire Reinforcement, Plain and Deformed, for Concrete has been revised to A1064/A1064M-13 developed by Committee A01.05, ASTM BOS Volume 01.04. 
  • A1088 - Standard Specification for Steel, Sheet, Cold-Rolled, Complex Phase (CP), Dual Phase (DP) and Transformation Induced Plasticity (TRIP) is a new standard, now available. A1088-13 developed by Committee A01.19, ASTM BOS Volume 01.03. 
  • B61 - Standard Specification for Steam or Valve Bronze Castings has been reapproved, available as B61-08(2013) developed by Committee B05.05, ASTM BOS Volume 02.01. 
  • B66 - Standard Specification for Bronze Castings for Steam Locomotive Wearing Parts has been reapproved (with editorial change), available as B66-06(2013)e1 developed by Committee B05.05, ASTM BOS Volume 02.01. 
  • B85/B85M - Standard Specification for Aluminum-Alloy Die Castings has been revised to B85/B85M-13 developed by Committee B07.01, ASTM BOS Volume 02.02. 
  • B98/B98M - Standard Specification for Copper-Silicon Alloy Rod, Bar and Shapes has been revised to B98/B98M-13 developed by Committee B05.02, ASTM BOS Volume 02.01. 
  • B151/B151M - Standard Specification for Copper-Nickel-Zinc Alloy (Nickel Silver) and Copper-Nickel Rod and Bar has been revised to B151/B151M-13 developed by Committee B05.02, ASTM BOS Volume 02.01. 
  • B176 - Standard Specification for Copper-Alloy Die Castings has been reapproved, available as B176-08(2013) developed by Committee B05.05, ASTM BOS Volume 02.01. 
  • B301/B301M - Standard Specification for Free-Cutting Copper Rod, Bar, Wire, and Shapes has been revised to B301/B301M-13 developed by Committee B05.02, ASTM BOS Volume 02.01. 
  • B371/B371M - Standard Specification for Copper-Zinc-Silicon Alloy Rod has been reapproved, available as B371/B371M-08(2013) developed by Committee B05.02, ASTM BOS Volume 02.01. 
  • B395/B395M - Standard Specification for U-Bend Seamless Copper and Copper Alloy Heat Exchanger and Condenser Tubes has been revised to B395/B395M-13 developed by Committee B05.04, ASTM BOS Volume 02.01. 
  • B428 - Standard Test Method for Angle of Twist in Rectangular and Square Copper and Copper Alloy Tube has been reapproved, available as B428-09(2013) developed by Committee B05.06, ASTM BOS Volume 02.01. 
  • B537 - Standard Practice for Rating of Electroplated Panels Subjected to Atmospheric Exposure has been reapproved (with editorial change), available as B537-70(2012)e1 developed by Committee B08.05, ASTM BOS Volume 02.05. 
  • B555 - Standard Guide for Measurement of Electrodeposited Metallic Coating Thicknesses by Dropping Test has been reapproved, available as B555-86(2012) developed by Committee B08.10, ASTM BOS Volume 02.05. 
  • B556 - Standard Guide for Measurement of Thin Chromium Coatings by Spot Test has been reapproved, available as B556-90(2012) developed by Committee B08.10, ASTM BOS Volume 02.05. 
  • B927/B927M - Standard Specification for Brass Rod, Bar, and Shapes has been revised to B927/B927M-13 developed by Committee B05.02, ASTM BOS Volume 02.01. 
  • C591 - Standard Specification for Unfaced Preformed Rigid Cellular Polyisocyanurate Thermal Insulation has been revised to C591-13 developed by Committee C16.22, ASTM BOS Volume 04.06. 
  • C651 - Standard Test Method for Flexural Strength of Manufactured Carbon and Graphite Articles Using Four-Point Loading at Room Temperature has been revised to C651-13 developed by Committee D02.F0, ASTM BOS Volume 05.05. 
  • C749 - Standard Test Method for Tensile Stress-Strain of Carbon and Graphite has been revised to C749-13 developed by Committee D02.F0, ASTM BOS Volume 05.05. 
  • C1515 - Standard Guide for Cleaning of Exterior Dimension Stone, Vertical And Horizontal Surfaces, New or Existing has been revised to C1515-13 developed by Committee C18.07, ASTM BOS Volume 04.07. 
  • C1729M - Standard Specification for Aluminum Jacketing for Insulation is a new standard, now available. C1729M-13 developed by Committee C16.40, ASTM BOS Volume 04.06. 
  • C1747/C1747M - Standard Test Method for Determining Potential Resistance to Degradation of Pervious Concrete by Impact and Abrasion has been revised to C1747/C1747M-13 developed by Committee C09.49, ASTM BOS Volume 04.02. 
  • C1777 - Standard Test Method for Rapid Determination of the Methylene Blue Value for Fine Aggregate or Mineral Filler Using a Colorimeter is a new standard, now available. C1777-13 developed by Committee C09.20, ASTM BOS Volume 04.02. 
  • D229 - Standard Test Methods for Rigid Sheet and Plate Materials Used for Electrical Insulation has been revised to D229-13 developed by Committee D09.07, ASTM BOS Volume 10.01. 
  • D348 - Standard Test Methods for Rigid Tubes Used for Electrical Insulation has been revised to D348-13 developed by Committee D09.07, ASTM BOS Volume 10.01. 
  • D349 - Standard Test Methods for Laminated Round Rods Used for Electrical Insulation has been revised to D349-13 developed by Committee D09.07, ASTM BOS Volume 10.01. 
  • D374M - Standard Test Methods for Thickness of Solid Electrical Insulation (Metric) has been revised to D374M-13 developed by Committee D09.12, ASTM BOS Volume 10.01. 
  • D396 - Standard Specification for Fuel Oils has been revised to D396-13b developed by Committee D02.E0, ASTM BOS Volume 05.01. 
  • D709 - Standard Specification for Laminated Thermosetting Materials has been revised to D709-13 developed by Committee D09.07, ASTM BOS Volume 10.01. 
  • D710 - Standard Specification for Vulcanized Fibre Sheets, Rods, and Tubes Used for Electrical Insulation has been revised to D710-13 developed by Committee D09.07, ASTM BOS Volume 10.01. 
  • D1711 - Standard Terminology Relating to Electrical Insulation has been revised to D1711-13 developed by Committee D09.94, ASTM BOS Volume 10.01. 
  • D1751 - Standard Specification for Preformed Expansion Joint Filler for Concrete Paving and Structural Construction (Nonextruding and Resilient Bituminous Types) has been reapproved (with editorial change), available as D1751-04(2013)e1 developed by Committee D04.34, ASTM BOS Volume 04.03. 
  • D1867 - Standard Specification for Copper-Clad Thermosetting Laminates for Printed Wiring has been revised to D1867-13 developed by Committee D09.07, ASTM BOS Volume 10.01. 
  • D2098 - Standard Test Method for Dynamic Water Resistance of Shoe Upper Leather by the Dow Corning Leather Tester has been revised to D2098-13 developed by Committee D31.03, ASTM BOS Volume 15.04. 
  • D2148 - Standard Test Methods for Bondable Silicone Rubber Tapes Used for Electrical Insulation has been revised to D2148-13 developed by Committee D09.07, ASTM BOS Volume 10.01. 
  • D2414 - Standard Test Method for Carbon Black—Oil Absorption Number (OAN) has been revised to D2414-13a developed by Committee D24.11, ASTM BOS Volume 09.01. 
  • D2656 - Standard Specification for Crosslinked Polyethylene Insulation for Wire and Cable Rated 2001 to 35 000 V has been revised to D2656-13 developed by Committee D09.18, ASTM BOS Volume 10.02. 
  • D2880 - Standard Specification for Gas Turbine Fuel Oils has been revised to D2880-13b developed by Committee D02.E0, ASTM BOS Volume 05.01. 
  • D2960 - Standard Test Method of Controlled Laundering Test Using Naturally Soiled Fabrics and Household Appliances (Withdrawn 2013) has been withdrawn, with no replacement. D2960-05 developed by Committee D12.25, ASTM BOS Volume 15.04. 
  • D3172 - Standard Practice for Proximate Analysis of Coal and Coke has been revised to D3172-13 developed by Committee D05.21, ASTM BOS Volume 05.06. 
  • D3685/D3685M - Standard Test Methods for Sampling and Determination of Particulate Matter in Stack Gases has been revised to D3685/D3685M-13 developed by Committee D22.03, ASTM BOS Volume 11.07. 
  • D3699 - Standard Specification for Kerosine has been revised to D3699-13b developed by Committee D02.E0, ASTM BOS Volume 05.01. 
  • D4239 - Standard Test Method for Sulfur in the Analysis Sample of Coal and Coke Using High-Temperature Tube Furnace Combustion has been editorially changed, available as D4239-13e1 developed by Committee D05.21, ASTM BOS Volume 05.06. 
  • D4661 - Standard Test Methods for Polyurethane Raw Materials: Determination of Total Chlorine in Isocyanates has been revised to D4661-13 developed by Committee D20.22, ASTM BOS Volume 08.02. 
  • D4683 - Standard Test Method for Measuring Viscosity of New and Used Engine Oils at High Shear Rate and High Temperature by Tapered Bearing Simulator Viscometer at 150?°C has been revised to D4683-13 developed by Committee D02.07, ASTM BOS Volume 05.02. 
  • D4741 - Standard Test Method for Measuring Viscosity at High Temperature and High Shear Rate by Tapered-Plug Viscometer has been revised to D4741-13 developed by Committee D02.07, ASTM BOS Volume 05.02. 
  • D4864 - Standard Test Method for Determination of Traces of Methanol in Propylene Concentrates by Gas Chromatography has been reapproved, available as D4864-90(2013) developed by Committee D02.D0.03, ASTM BOS Volume 05.02. 
  • D5481 - Standard Test Method for Measuring Apparent Viscosity at High-Temperature and High-Shear Rate by Multicell Capillary Viscometer has been revised to D5481-13 developed by Committee D02.07, ASTM BOS Volume 05.02. 
  • D5528 - Standard Test Method for Mode I Interlaminar Fracture Toughness of Unidirectional Fiber-Reinforced Polymer Matrix Composites has been revised to D5528-13 developed by Committee D30.06, ASTM BOS Volume 15.03. 
  • D6380/D6380M - Standard Specification for Asphalt Roll Roofing (Organic Felt) has been editorially changed, available as D6380/D6380M-03(2013)e1 developed by Committee D08.02, ASTM BOS Volume 04.04. 
  • D6381/D6381M - Standard Test Method for Measurement of Asphalt Shingle Mechanical Uplift Resistance has been reapproved (with editorial change), available as D6381/D6381M-08(2013)e1 developed by Committee D08.02, ASTM BOS Volume 04.04. 
  • D6671/D6671M - Standard Test Method for Mixed Mode I-Mode II Interlaminar Fracture Toughness of Unidirectional Fiber Reinforced Polymer Matrix Composites has been revised to D6671/D6671M-13 developed by Committee D30.06, ASTM BOS Volume 15.03. 
  • D6676/D6676M - Standard Test Method for Cathodic Disbonding of Exterior Pipeline Coatings at Elevated Temperatures Using Interior Heating has been reinstated as D6676/D6676M-13 developed by Committee D01.48, ASTM BOS Volume 06.02. 
  • D7132 - Standard Test Method for Determination of Retained Blowing Agent in Extruded Polystyrene Foam has been revised to D7132-13 developed by Committee D20.70, ASTM BOS Volume 08.03. 
  • D7151 - Standard Test Method for Determination of Elements in Insulating Oils by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES) has been revised to D7151-13 developed by Committee D27.03, ASTM BOS Volume 10.03. 
  • D7309 - Standard Test Method for Determining Flammability Characteristics of Plastics and Other Solid Materials Using Microscale Combustion Calorimetry has been revised to D7309-13 developed by Committee D20.30, ASTM BOS Volume 08.03. 
  • D7668 - Standard Test Method for Determination of Derived Cetane Number (DCN) of Diesel Fuel Oils—Ignition Delay and Combustion Delay Using a Constant Volume Combustion Chamber Method has been revised to D7668-12a developed by Committee D02.01.0C, ASTM BOS Volume 05.05. 
  • D7855/D7855M - Standard Test Method for Determination of Mold Growth on Coated Building Products Designed for Interior Applications Using an Environmental Chamber and Indirect Inoculation is a new standard, now available. D7855/D7855M-13 developed by Committee D01.28, ASTM BOS Volume 06.01. 
  • D7893 - Standard Guide for Corrosion Test Panel Preparation, Testing, and Rating of Coil-Coated Building Products is a new standard, now available. D7893-13 developed by Committee D01.53, ASTM BOS Volume 06.02. 
  • E253 - Standard Terminology Relating to Sensory Evaluation of Materials and Products has been revised to E253-13a developed by Committee E18.01, ASTM BOS Volume 15.08. 
  • E308 - Standard Practice for Computing the Colors of Objects by Using the CIE System has been revised to E308-13 developed by Committee E12.04, ASTM BOS Volume 06.01. 
  • E398 - Standard Test Method for Water Vapor Transmission Rate of Sheet Materials Using Dynamic Relative Humidity Measurement has been revised to E398-13 developed by Committee F02.10, ASTM BOS Volume 15.10. 
  • E814 - Standard Test Method for Fire Tests of Penetration Firestop Systems has been revised to E814-13 developed by Committee E05.11, ASTM BOS Volume 04.07. 
  • E833 - Standard Terminology of Building Economics has been revised to E833-13b developed by Committee E06.81, ASTM BOS Volume 04.11. 
  • E871 - Standard Test Method for Moisture Analysis of Particulate Wood Fuels has been reapproved, available as E871-82(2013) developed by Committee E48.05, ASTM BOS Volume 11.06. 
  • E872 - Standard Test Method for Volatile Matter in the Analysis of Particulate Wood Fuels has been reapproved, available as E872-82(2013) developed by Committee E48.05, ASTM BOS Volume 11.06. 
  • E1225 - Standard Test Method for Thermal Conductivity of Solids Using the Guarded-Comparative-Longitudinal Heat Flow Technique has been revised (with title change) to E1225-13 developed by Committee E37.05, ASTM BOS Volume 14.02. 
  • E1409 - Standard Test Method for Determination of Oxygen and Nitrogen in Titanium and Titanium Alloys by Inert Gas Fusion has been revised to E1409-13 developed by Committee E01.06, ASTM BOS Volume 03.05. 
  • E1621 - Standard Guide for Elemental Analysis by Wavelength Dispersive X-Ray Fluorescence Spectrometry has been revised (with title change) to E1621-13 developed by Committee E01.20, ASTM BOS Volume 03.05. 
  • E1699 - Standard Practice for Performing Value Engineering (VE)/Value Analysis (VA) of Projects, Products and Processes has been revised (with title change) to E1699-13 developed by Committee E06.81, ASTM BOS Volume 04.11. 
  • E1859/E1859M - Standard Test Method for Friction Coefficient Measurements Between Tire and Pavement Using a Variable Slip Technique has been editorially changed, available as E1859/E1859M-11e1 developed by Committee E17.21, ASTM BOS Volume 04.03. 
  • E1886 - Standard Test Method for Performance of Exterior Windows, Curtain Walls, Doors, and Impact Protective Systems Impacted by Missile(s) and Exposed to Cyclic Pressure Differentials has been revised to E1886-13a developed by Committee E06.51, ASTM BOS Volume 04.11. 
  • E2058 - Standard Test Methods for Measurement of Material Flammability Using a Fire Propagation Apparatus (FPA) has been revised (with title change) to E2058-13a developed by Committee E05.22, ASTM BOS Volume 04.07. 
  • E2242 - Standard Test Method for Column Percolation Extraction of Mine Rock by the Meteoric Water Mobility Procedure has been revised to E2242-13 developed by Committee E01.02, ASTM BOS Volume 03.05. 
  • E2260 - Standard Guide for Repointing (Tuckpointing) Historic Masonry has been editorially changed, available as E2260-03(2012)e1 developed by Committee E06.24, ASTM BOS Volume 04.12. 
  • E2340/E2340M - Standard Test Method for Measuring the Skid Resistance of Pavements and Other Trafficked Surfaces Using a Continuous Reading, Fixed-Slip Technique has been editorially changed, available as E2340/E2340M-11e1 developed by Committee E17.21, ASTM BOS Volume 04.03. 
  • E2606 - Standard Practice for Receipt Notification as a Result of Tangible Asset Movement has been revised (with title change) to E2606-13 developed by Committee E53.01, ASTM BOS Volume 04.12. 
  • E2618 - Standard Test Method for Measurement of Particulate Emissions and Heating Efficiency of Solid Fuel-Fired Hydronic Heating Appliances has been revised (with title change) to E2618-13 developed by Committee E06.54, ASTM BOS Volume 04.12. 
  • E2651 - Standard Guide for Powder Particle Size Analysis has been revised to E2651-13 developed by Committee E29.02, ASTM BOS Volume 14.02. 
  • E2891 - Standard Guide for Multivariate Data Analysis in Pharmaceutical Development and Manufacturing Applications is a new standard, now available. E2891-13 developed by Committee E55.01, ASTM BOS Volume 14.02. 
  • E2893 - Standard Guide for Greener Cleanups is a new standard, now available. E2893-13 developed by Committee E50.04, ASTM BOS Volume 11.05. 
  • E2951 - Standard Guide for Community Emergency Preparedness for Persons with Disabilities is a new standard, now available. E2951-13 developed by Committee E54.02, ASTM BOS Volume 15.08. 
  • F22 - Standard Test Method for Hydrophobic Surface Films by the Water-Break Test has been revised to F22-13 developed by Committee E21.05, ASTM BOS Volume 15.03. 
  • F311 - Standard Practice for Processing Aerospace Liquid Samples for Particulate Contamination Analysis Using Membrane Filters has been reapproved, available as F311-08(2013) developed by Committee E21.05, ASTM BOS Volume 15.03. 
  • F404 - Standard Consumer Safety Specification for High Chairs has been revised to F404-13 developed by Committee F15.16, ASTM BOS Volume 15.11. 
  • F560/F560M - Standard Specification for Unalloyed Tantalum for Surgical Implant Applications (UNS R05200, UNS R05400) has been revised (with designation change) to F560/F560M-13 developed by Committee F04.12, ASTM BOS Volume 13.01. 
  • F1043 - Standard Specification for Strength and Protective Coatings on Steel Industrial Fence Framework has been revised to F1043-13 developed by Committee F14.40, ASTM BOS Volume 01.06. 
  • F1083 - Standard Specification for Pipe, Steel, Hot-Dipped Zinc-Coated (Galvanized) Welded, for Fence Structures has been revised to F1083-13 developed by Committee F14.40, ASTM BOS Volume 01.06. 
  • F1249 - Standard Test Method for Water Vapor Transmission Rate Through Plastic Film and Sheeting Using a Modulated Infrared Sensor has been revised to F1249-13 developed by Committee F02.10, ASTM BOS Volume 15.10. 
  • F1314/F1314M - Standard Specification for Wrought Nitrogen Strengthened 22 Chromium–13 Nickel–5 Manganese–2.5 Molybdenum Stainless Steel Alloy Bar and Wire for Surgical Implants (UNS S20910) has been revised (with designation change) to F1314/F1314M-13a developed by Committee F04.12, ASTM BOS Volume 13.01. 
  • F1959/F1959M - Standard Test Method for Determining the Arc Rating of Materials for Clothing has been revised to F1959/F1959M-13 developed by Committee F18.65, ASTM BOS Volume 10.03. 
  • F2066/F2066M - Standard Specification for Wrought Titanium-15 Molybdenum Alloy for Surgical Implant Applications (UNS R58150) has been revised (with designation change) to F2066/F2066M-13 developed by Committee F04.12, ASTM BOS Volume 13.01. 
  • F2549 - Standard Consumer Safety Specification for Frame Child Carriers has been revised to F2549-13 developed by Committee F15.21, ASTM BOS Volume 15.11. 
  • F2550 - Standard Practice for Locating Leaks in Sewer Pipes By Measuring the Variation of Electric Current Flow Through the Pipe Wall has been revised (with title change) to F2550-13 developed by Committee F36.20, ASTM BOS Volume 04.12. 
  • F2633 - Standard Specification for Wrought Seamless Nickel-Titanium Shape Memory Alloy Tube for Medical Devices and Surgical Implants has been revised to F2633-13 developed by Committee F04.12, ASTM BOS Volume 13.02. 
  • F2710 - Standard Consumer Safety Performance Specification for Commercial Cribs has been revised to F2710-13 developed by Committee F15.57, ASTM BOS Volume 15.11. 
  • F2930 - Standard Guide for Compliance with Light Sport Aircraft Standards has been revised to F2930-13 developed by Committee F37.70, ASTM BOS Volume 15.11. 
  • F2947 - Standard Specification for 150 to 1500 mm [6 to 60 in.] Annular Corrugated Profile-Wall Polyethylene (PE) Pipe and Fittings for Sanitary Sewer Applications has been editorially changed, available as F2947-12e1 developed by Committee F17.62, ASTM BOS Volume 08.04. 
  • F3013 - Standard Test Method for Density of Topsoil and Blended Soils In-place by the Core Displacement Method is a new standard, now available. F3013-13 developed by Committee F08.64, ASTM BOS Volume 15.07. 
  • G13/G13M - Standard Test Method for Impact Resistance of Pipeline Coatings (Limestone Drop Test) has been reinstated as G13/G13M-13 developed by Committee D01.48, ASTM BOS Volume 06.02. 
  • G75 - Standard Test Method for Determination of Slurry Abrasivity (Miller Number) and Slurry Abrasion Response of Materials (SAR Number) has been reapproved, available as G75-07(2013) developed by Committee G02.30, ASTM BOS Volume 03.02. 
  • G81 - Standard Test Method for Jaw Crusher Gouging Abrasion Test has been reapproved, available as G81-97a(2013) developed by Committee G02.30, ASTM BOS Volume 03.02. 
  • G88 - Standard Guide for Designing Systems for Oxygen Service has been revised to G88-13 developed by Committee G04.02, ASTM BOS Volume 14.04. 
  • G115 - Standard Guide for Measuring and Reporting Friction Coefficients has been reapproved, available as G115-10(2013) developed by Committee G02.50, ASTM BOS Volume 03.02. 
  • G132 - Standard Test Method for Pin Abrasion Testing has been reapproved, available as G132-96(2013) developed by Committee G02.30, ASTM BOS Volume 03.02. 
  • G143 - Standard Test Method for Measurement of Web/Roller Friction Characteristics has been reapproved, available as G143-03(2013) developed by Committee G02.50, ASTM BOS Volume 03.02. 
  • G164 - Standard Test Method for Determination of Surface Lubrication on Flexible Webs has been reapproved, available as G164-99(2013) developed by Committee G02.50, ASTM BOS Volume 03.02. 
  • G172 - Standard Guide for Statistical Analysis of Accelerated Service Life Data has been editorially changed, available as G172-02(2010)e1 developed by Committee G03.08, ASTM BOS Volume 14.04. 
  • G194 - Standard Test Method for Measuring Rolling Friction Characteristics of a Spherical Shape on a Flat Horizontal Plane has been reapproved, available as G194-08(2013) developed by Committee G02.50, ASTM BOS Volume 03.02. 

Published in international.