BRITISH STANDARDS

You can now purchase PDFs of British Standards from Standards New Zealand – please email enquiries@standards.co.nz or call 0800 782 632 during business hours to order PDFs. British Standard publications in hardcopy format are also available for purchase from our web site www.standards.co.nz by entering the Standard number and selecting the BSI button in the search panel.


BRITISH PUBLICATIONS

The publications listed below are new and revised British Standards that were made available last month. An existing BSI publication bearing a number identical to one announced below is automatically withdrawn unless stated otherwise. In all other cases of supersession, details are given and a corresponding entry appears in the 'British Standards withdrawn' section.

  • BS 1133-8:2011 Packaging code. Guidance on wooden boxes, cases and crates
    Supersedes BS 1133-8:1991
  • BS 1722-18:2011 Fences. Specification for free-standing temporary steel mesh perimeter fencing panels
    Supersedes DD 1722-18:2007
  • BS 1881-113:2011 Testing concrete. Method for making and curing no-fines test cubes
    Supersedes BS 1881-113:1983
  • BS 1881-119:2011 Testing concrete. Method for determination of compressive strength using portions of beams broken in flexure (equivalent cube method)
    Supersedes BS 1881-119:1983
  • BS 5250:2011 Code of practice for control of condensation in buildings
    Supersedes BS 5250:2002+A1:2005
  • BS 5266-1:2011 Emergency lighting. Code of practice for the emergency escape lighting of premises
    Supersedes BS 5266-1:2005 and BS 5266-10:2008
  • BS 5655-6:2011 Lifts and service lifts. Code of practice for the selection, installation and location of new lifts
    Supersedes BS 5655-6:2002
  • BS 6187:2011 Code of practice for full and partial demolition
    Supersedes BS 6187:2000
  • BS 6644:2011 Specification for the installation and maintenance of gas-fired hot water boilers of rated inputs between 70 kW (net) and 1.8 MW (net) (2nd and 3rd family gases)
    Supersedes BS 6644:2005+A1:2008
  • BS 7430:2011 Code of practice for protective earthing of electrical installations
    Supersedes BS 7430:1998
  • BS 7843-1:2012 Acquisition and management of meteorological precipitation data from a rain gauge network. Guide for the design, development and review of a rain gauge network
    Supersedes BS 7843-1.1:1996, BS 7843-1.2:1996, BS 7843-3.1:1999 and BS 7843-3.2:2005 which remain current, supersedes BS 7843-2.1:1996 which is withdrawn
  • BS 7843-2:2012 Acquisition and management of meteorological precipitation data from a rain gauge network. Code of practice for operating rain gauges and managing precipitation data
    Supersedes BS 7843-2.1:1996, BS 7843-2.2:1996 and BS 7843-2.3:1996
  • BS 7870-1:2011 LV and MV polymeric insulated cables for use by distribution and generation utilities. General
    Supersedes BS 7870-1:1996
  • BS 7870-2:2011 LV and MV polymeric insulated cables for use by distribution and generation utilities. Methods of test
    Supersedes BS 7870-2:1999
  • BS 7870-3.11:2011 LV and MV polymeric insulated cables for use by distribution and generation utilities. Specification for distribution cables of rated voltage 0.6/1 kV. XLPE insulated combined neutral and earth copper wire concentric cables with copper or aluminium conductors
    Supersedes BS 7870-3.11:2001
  • BS 7870-3.12:2011 LV and MV polymeric insulated cables for use by distribution and generation utilities. Specification for distribution cables of rated voltage 0.6/1 kV. XLPE insulated combined neutral and earth copper wire concentric cables with copper or aluminium conductors, having low emission of smoke and corrosive gases when affected by fire
    Supersedes BS 7870-3.12:2001
  • BS 7870-3.21:2011 LV and MV polymeric insulated cables for use by distribution and generation utilities. Specification for distribution cables of rated voltage 0.6/1 kV. XLPE insulated split concentric cables with copper or aluminium conductors
    Supersedes BS 7870-3.21:2001
  • BS 7870-3.22:2011 LV and MV polymeric insulated cables for use by distribution and generation utilities. Specification for distribution cables of rated voltage 0.6/1 kV. XLPE insulated split concentric cables with copper or aluminium conductors, having low emission of smoke and corrosive gases when affected by fire
  • BS 7870-3.40:2011 LV and MV polymeric insulated cables for use by distribution and generation utilities. Specification for distribution cables of rated voltage 0.6/1 kV. XLPE insulated, copper wire waveform concentric cables with solid aluminium conductors
    Supersedes BS 7870-3.40:2001
  • BS 7870-3.50:2011 LV and MV polymeric insulated cables for use by distribution and generation utilities. Specification for distribution cables of rated voltage 0.6/1 kV. XLPE insulated, copper wire waveform or helical concentric cables with solid aluminium conductors, having low emission of smoke and corrosive gases when affected by fire
    Supersedes BS 7870-3.50:2005
  • BS 7870-4.10:2011 LV and MV polymeric insulated cables for use by distribution and generation utilities. Specification for distribution cables with extruded insulation of rated voltages of 11 kV to 33 kV. Single-core 11 kV to 33 kV cables
    Supersedes BS 7870-4.10:1999
  • BS 7870-4.11:2011 LV and MV polymeric insulated cables for use by distribution and generation utilities. Specification for distribution cables with extruded insulation for rated voltages of 11 kV and 33 kV. Single-core 33 kV lead sheathed cables
    Supersedes BS 7870-4.11:1999
  • BS 7870-4.20:2011 LV and MV polymeric insulated cables for use by distribution and generation utilities. Specification for distribution cables with extruded insulation for rated voltages of 11 kV to 33 kV. Three-core 11 kV cables
    Supersedes BS 7870-4.20:1999
  • BS 7870-5:2011 LV and MV polymeric insulated cables for use by distribution and generation utilities. Polymeric insulated aerial bundled conductors (ABC) of rated voltage 0.6/1 kV for overhead distribution
    Supersedes BS 7870-5:1999
  • BS 8006-2:2011 Code of practice for strengthened/reinforced soils. Soil nail design
    Supersedes BS 8006:1995
  • BS 8103-1:2011 Structural design of low-rise buildings. Code of practice for stability, site investigation, foundations, precast concrete floors and ground floor slabs for housing
    Supersedes BS 8103-1:1995 and BS 8103-4:1995
  • BS 8551:2011 Provision and management of temporary water supplies and distribution networks (not including provisions for statutory emergencies). Code of practice
  • BS 8558:2011 Guide to the design, installation, testing and maintenance of services supplying water for domestic use within buildings and their curtilages. Complimentary guidance to BS EN 806
    Supersedes BS 6700:2006+A1:2009 which remains current
  • BS 8572:2011 Procurement of facility-related services. Guide
  • BS 8660-1:2011 Gas-fired micro-cogeneration appliances of rated thermal input not exceeding 70 kW net. Specification for selection, installation, inspection, commissioning, servicing and maintenance of Stirling engine micro-cogeneration appliances
  • BS 8888:2011 Technical product documentation and specification
    Supersedes BS 8888:2008
  • BS 8904:2011 Guidance for community sustainable development
  • BS 9991:2011 Fire safety in the design, management and use of residential buildings. Code of practice
    Supersedes BS 5588-1:1990
  • BS 10500:2011 Specification for an anti-bribery management system (ABMS)
  • BS 11000-2:2011 Collaborative business relationships. Guide to implementing BS 11000-1
  • BS 5L 100:2011 Procedure for inspection, testing and acceptance of wrought aluminium and aluminium alloys
    Supersedes BS 4L 100:1993
  • BS 5L 101:2011 Procedure for inspection, testing and acceptance of aluminium-base and magnesium-base ingots and castings
    Supersedes BS 4L 101:1990
  • BS 3L 500:2011 Procedure for inspection, testing and acceptance of wrought magnesium base alloys
    Supersedes BS 2L 500:1973

BS EN publications

The following are British Standard implementations of the English language versions of European Standards (ENs). The date referenced in the identifier is the date of the European Standard. You can now purchase PDFs of British Standards from Standards New Zealand – please email enquiries@standards.co.nz or call 0800 782 632 during business hours to order PDFs.

  • BS EN ISO 534:2011 Paper and board. Determination of thickness, density and specific volume
    Supersedes BS EN ISO 534:2005
  • BS EN 771-1:2011 Specification for masonry units. Clay masonry units
    Supersedes BS EN 771-1:2003
  • BS EN 1034-3:2011 Safety of machinery. Safety requirements for the design and construction of paper making and finishing machines. Rereelers and winders
    Supersedes BS EN 1034-3:1999+A1:2009
  • BS EN ISO 1043-1:2011 Plastics. Symbols and abbreviated terms. Basic polymers and their special characteristics
    Supersedes BS EN ISO 1043-1:2002
  • BS EN ISO 1043-2:2011 Plastics. Symbols and abbreviated terms. Fillers and reinforcing materials
    Supersedes BS EN ISO 1043-2:2001
  • BS EN ISO 1119:2011 Geometrical product specifications (GPS). Series of conical tapers and taper angles
    Supersedes BS EN ISO 1119:2002
  • BS EN ISO 1133-2:2011 Plastics. Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics. Method for materials sensitive to time-temperature history and/or moisture
    Supersedes BS EN ISO 1133:2005
  • BS EN ISO 1135-4:2011 Transfusion equipment for medical use. Transfusion sets for single use
    Supersedes BS EN ISO 1135-4:2010
  • BS EN 1172:2011 Copper and copper alloys. Sheet and strip for building purposes
    Supersedes BS EN 1172:1997
  • BS EN 1371-1:2011 Founding. Liquid penetrant testing. Sand, gravity die and low pressure die castings
    Supersedes BS EN 1371-1:1997
  • BS EN 1458-1:2011 Domestic direct gas-fired tumble dryers of types B22D and B23D, of nominal heat input not exceeding 6 kW. Safety
    Supersedes BS EN 1458-1:2000
  • BS EN 1458-2:2011 Domestic direct gas-fired tumble dryers of types B22D and B23D, of nominal heat input not exceeding 6 kW. Rational use of energy
    Supersedes BS EN 1458-2:1999
  • BS EN 1501-1:2011 Refuse collection vehicles. General requirements and safety requirements. Rear loaded refuse collection vehicles
    Supersedes BS EN 1501-1:1998+A2:2009
  • BS EN 1501-5:2011 Refuse collection vehicles. General requirements and safety requirements. Lifting devices for refuse collection vehicles
    Supersedes BS EN 1501-1:1998+A2:2009
  • BS EN ISO 1518-2:2011 Paints and varnishes. Determination of scratch resistance. Variable-loading method
    Supersedes the dual numbered standard BS EN ISO 12137-2:2006, BS 3900-E18:1997
  • BS EN 1564:2011 Founding. Ausferritic spheroidal graphite cast irons
    Supersedes BS EN 1564:1997
  • BS EN 2240-100:2011 Aerospace series. Lamps, incandescent. Lamp, code 2078. Product standard
  • BS EN 2240-101:2011 Aerospace series. Lamps, incandescent. Lamp, code 404-02. Product standard
  • BS EN ISO 2431:2011 Paints and varnishes. Determination of flow time by use of flow cups
    Supersedes the dual numbered standard BS EN ISO 2431:1996, BS 3900-A6:1996
  • BS EN 2824:2011 Aerospace series. Burning behaviour of nonmetallic materials under the influence of radiating heat and flames. Determination of smoke density and gas components in the smoke of materials. Test equipment apparatus and media
  • BS EN ISO 3035:2011 Corrugated fibreboard. Determination of flat crush resistance
    Supersedes BS EN 23035:1994
  • BS EN 3310:2011 Aerospace series. Titanium alloy TI-P64001 (Ti-6Al-4V). Not heat treated. Forging stock, for annealed forgings. De ? 360 mm
    Supersedes BS 3TA 12:2009
  • BS EN ISO 3450:2011 Earth-moving machinery. Wheeled or highspeed rubber-tracked machines. Performance requirements and test procedures for brake systems
    Supersedes BS EN ISO 3450:2008
  • BS EN 3844-1:2011 Aerospace series. Flammability of non metallic materials. Small burner test, vertical. Determination of the vertical flame propagation
  • BS EN 3844-2:2011 Aerospace series. Flammability of non metallic materials. Small burner test, horizontal. Determination of the horizontal flame propagation
  • BS EN 3844-3:2011 Aerospace series. Flammability of non metallic materials. Small burner test, 45°. Determination of the resistance of material to flame and glow propagation and to flame penetration
  • BS EN 4165-025:2011 Aerospace series. Connectors, electrical, rectangular, modular. Operating temperature 175°C continuous. Module receptacle. Product Norm
  • BS EN 4612-009:2011 Aerospace series. Cables, electrical, for general purpose, single and multicore assembly. XLETFE Family. Jacketed or screened and jacketed. Silver plated copper. Operating temperatures, between -65°C and 150°C. Dual extruded wall for open applications, with jacket without screen. UV laser printable. Product standard
  • BS EN 4644-003:2011 Aerospace series. Connector, electrical and optical, rectangular, modular, rectangular inserts, operating temperature 175°C (or 125°C) continuous. Rectangular inserts. Product standard
    Supersedes BS EN 4644-003:2009
  • BS EN 4644-131:2011 Aerospace series. Connector, electrical and optical, rectangular, modular, rectangular inserts, operating temperature 175°C (or 125°C) continuous. Size 3 plug for rack and panel applications. Product standard
  • BS EN 4644-133:2011 Aerospace series. Connector, electrical and optical, rectangular, modular, rectangular inserts, operating temperature 175°C (or 125°C) continuous. Size 3 receptacle for rack and panel application. Product standard
  • BS EN 4644-141:2011 Aerospace series. Connector, electrical and optical, rectangular, modular, rectangular inserts, operating temperature 175°C (or 125°C) continuous. Size 4 plug for rack and panel applications. Product standard
  • BS EN ISO 4753:2011 Fasteners. Ends of parts with external ISO metric thread
    Supersedes BS EN ISO 4753:2000
  • BS EN 6059-100:2011 Aerospace series. Electrical cables, installation. Protection sleeves. Test methods. General
  • BS EN ISO 6224:2011 Thermoplastics hoses, textile-reinforced, for general-purpose water applications. Specification
    Supersedes BS EN ISO 6224:2008
  • BS EN ISO 7783:2011 Paints and varnishes. Determination of water vapour transmission properties. Cup method
    Supersedes the dual numbered standard BS EN ISO 7783-1:2000, BS 3900-G9:1996 and BS EN ISO 7783-2:1999
  • BS EN ISO 9241-303:2011 Ergonomics of human-system interaction. Requirements for electronic visual displays
    Supersedes BS EN ISO 9241-303:2008
  • BS EN 10257-1:2011 Zinc or zinc alloy coated non-alloy steel wire for armouring either power cables or telecommunication cables. Land cables
    Supersedes BS EN 10257-1:1998
  • BS EN 10257-2:2011 Zinc or zinc alloy coated non-alloy steel wire for armouring either power cables or telecommunication cables. Submarine cables
    Supersedes BS EN 10257-2:1998
  • BS EN ISO 11127-2:2011 Preparation of steel substrates before application of paints and related products. Test methods for non-metallic blast-cleaning abrasives. Determination of particle size distribution
    Supersedes BS EN ISO 11127-2:1998
  • BS EN ISO 11127-4:2011 Preparation of steel substrates before application of paints and related products. Test methods for non-metallic blast-cleaning abrasives. Assessment of hardness by a glass slide test
    Supersedes BS EN ISO 11127-4:1998
  • BS EN ISO 11127-5:2011 Preparation of steel substrates before application of paints and related products. Test methods for non-metallic blast-cleaning abrasives. Determination of moisture
    Supersedes BS EN ISO 11127-5:1998
  • BS EN ISO 11127-6:2011 Preparation of steel substrates before application of paints and related products. Test methods for non-metallic blast-cleaning abrasives. Determination of water-soluble contaminants by conductivity measurement
    Supersedes BS EN ISO 11127-6:1998
  • BS EN ISO 11127-7:2011 Preparation of steel substrates before application of paints and related products. Test methods for non-metallic blast-cleaning abrasives. Determination of water-soluble chlorides
    Supersedes BS EN ISO 11127-7:1998
  • BS EN ISO 11148-1:2011 Hand-held non-electric power tools. Safety requirements. Assembly power tools for non-threaded mechanical fasteners
    Supersedes BS EN 792-1:2000+A1:2008
  • BS EN ISO 11148-2:2011 Hand-held non-electric power tools. Safety requirements. Cutting-off and crimping power tools
    Supersedes BS EN 792-2:2000+A1:2008
  • BS EN ISO 11148-5:2011 Hand-held non-electric power tools. Safety requirements. Rotary percussive drills
    Supersedes BS EN 792-5:2000+A1:2008
  • BS EN ISO 11148-9:2011 Hand-held non-electric power tools. Safety requirements. Die grinders
    Supersedes BS EN 792-9:2001+A1:2008
  • BS EN ISO 11680-2:2011 Machinery for forestry. Safety requirements and testing for pole-mounted powered pruners. Machines for use with back-pack power source
    Supersedes BS EN ISO 11680-2:2008 and BS ISO 14740:1998
  • BS EN ISO 11681-1:2011 Machinery for forestry. Portable chain-saw safety requirements and testing. Chain-saws for forest service
    Supersedes BS EN ISO 11681-1:2008
  • BS EN ISO 11681-2:2011 Machinery for forestry. Portable chain-saw safety requirements and testing. Chain-saws for tree service
    Supersedes BS EN ISO 11681-2:2008
  • BS EN ISO 11850:2011 Machinery for forestry. General safety requirements
    Supersedes BS EN 14861:2004+A1:2009 and BS ISO 11850:2003
  • BS EN ISO 11990-1:2011 Lasers and laser-related equipment. Determination of laser resistance of tracheal tubes. Tracheal tube shaft
    Supersedes BS EN ISO 11990:2003
  • BS EN ISO 12137:2011 Paints and varnishes. Determination of mar resistance
    Supersedes the dual numbered standard BS EN ISO 12137-1:2006, BS 3900-E17:1997
  • BS EN 12201-1:2011 Plastics piping systems for water supply, and for drainage and sewerage under pressure. Polyethylene (PE). General
    Supersedes BS EN 12201-1:2003 and BS EN 13244-1:2002
  • BS EN 12201-2:2011 Plastics piping systems for water supply, and for drainage and sewerage under pressure. Polyethylene (PE). Pipes
    Supersedes BS EN 12201-2:2003 and BS EN 13244-2:2002
  • BS EN 12201-3:2011 Plastics piping systems for water supply, and for drainage and sewerage under pressure. Polyethylene (PE). Fittings
    Supersedes BS EN 12201-3:2003 and BS EN 13244-3:2002
  • BS EN 12201-5:2011 Plastics piping systems for water supply, and for drainage and sewerage under pressure. Polyethylene (PE). Fitness for purpose of the system
    Supersedes BS EN 12201-5:2003 and BS EN 13244-5:2002
  • BS EN 12680-3:2011 Founding. Ultrasonic testing. Spheroidal graphite cast iron castings
    Supersedes BS EN 12680-3:2003
  • BS EN 12952-5:2011 Water-tube boilers and auxiliary installations. Workmanship and construction of pressure parts of the boiler
    Supersedes BS EN 12952-5:2001
  • BS EN 13037:2011 Soil improvers and growing media. Determination of pH
    Supersedes BS EN 13037:2000
  • BS EN 13038:2011 Soil improvers and growing media. Determination of electrical conductivity
    Supersedes BS EN 13038:2000
  • BS EN 13039:2011 Soil improvers and growing media. Determination of organic matter content and ash
    Supersedes BS EN 13039:2000
  • BS EN 13041:2011 Soil improvers and growing media. Determination of physical properties. Dry bulk density, air volume, water volume, shrinkage value and total pore space
    Supersedes BS EN 13041:2000
  • BS EN 13126-1:2011 Building hardware. Hardware for windows and door height windows. Requirements and test methods. Requirements common to all types of hardware
    Supersedes BS EN 13126-1:2006
  • BS EN 13126-3:2011 Building hardware. Hardware for windows and door-height windows. Requirements and test methods. Handles, primarily for Tilt&Turn, Tilt-First and Turn-Only hardware
    Supersedes DD CEN/TS 13126-3:2004
  • BS EN 13126-5:2011 Building hardware. Hardware for windows and door height windows. Requirements and test methods. Devices that restrict the opening of windows and door height windows
    Supersedes DD CEN/TS 13126-5:2004
  • BS EN ISO 13503-1:2011 Petroleum and natural gas industries. Completion fluids and materials. Measurement of viscous properties of completion fluids
    Supersedes BS EN ISO 13503-1:2005
  • BS EN 13523-17:2011 Coil coated metals. Test methods. Adhesion of strippable films
    Supersedes BS EN 13523-17:2004
  • BS EN ISO 13706:2011 Petroleum, petrochemical and natural gas industries. Air-cooled heat exchangers
    Supersedes BS EN ISO 13706:2005
  • BS EN ISO 14405-2:2011 Geometrical product specifications (GPS). Dimensional tolerancing. Dimensions other than linear sizes
    Supersedes BS ISO 406:1987
  • BS EN ISO 15001:2011 Anaesthetic and respiratory equipment. Compatibility with oxygen
    Supersedes BS EN ISO 15001:2010
  • BS EN 15022-4:2011 Copper and copper alloys. Determination of tin content. Medium tin content. Flame atomic absorption spectrometric method (FAAS)
    Supersedes DD CEN/TS 15022-4:2006
  • BS EN 15150:2011 Solid biofuels. Determination of particle density
    Supersedes DD CEN/TS 15150:2005
  • BS EN 15221-6:2011 Facility management. Area and space measurement in facility management
    Partially supersedes BS 7641:1993
  • BS EN ISO 15320:2011 Pulp, paper and board. Determination of pentachlorophenol in an aqueous extract
    Supersedes BS EN ISO 15320:2003
  • BS EN 15359:2011 Solid recovered fuels. Specifications and classes
    Supersedes DD CEN/TS 15359:2006
  • BS EN ISO 15378:2011 Primary packaging materials for medicinal products. Particular requirements for the application of ISO 9001:2008, with reference to Good Manufacturing Practice (GMP)
    Supersedes BS EN ISO 15378:2007
  • BS EN 15700:2011 Safety for conveyor belts for winter sport or leisure use
  • BS EN 15759-1:2011 Conservation of cultural property. Indoor climate. Guidelines for heating churches, chapels and other places of worship
  • BS EN 15882-1:2011 Extended application of results from fire resistance tests for service installations. Ducts
  • BS EN 15906:2011 Winter maintenance equipment. Snow removal machines with rotating tools. Specification and clearing capacity
  • BS EN 15958:2011 Fertilizers. Extraction of water soluble phosphorus
    Supersedes DD CEN/TS 15958:2009
  • BS EN 15959:2011 Fertilizers. Determination of extracted phosphorus
    Supersedes DD CEN/TS 15959:2009
  • BS EN 15960:2011 Fertilizers. Extraction of total calcium, total magnesium, total sodium and total sulfur in the forms of sulfates
    Supersedes DD CEN/TS 15960:2009
  • BS EN 15961:2011 Fertilizers. Extraction of water-soluble calcium, magnesium, sodium and sulfur in the form of sulfates
    Supersedes DD CEN/TS 15961:2009
  • BS EN 15978:2011 Sustainability of construction works. Assessment of environmental performance of buildings. Calculation method
  • BS EN 16003:2011 Chemicals used for treatment of water intended for human consumption. Calcium magnesium carbonate
  • BS EN 16004:2011 Chemicals used for treatment of water intended for human consumption. Magnesium oxide
  • BS EN 16018:2011 Non-destructive testing. Terminology. Terms used in ultrasonic testing with phased arrays
  • BS EN 16032:2011 Fertilizers. Extraction and determination of elemental sulphur
    Supersedes DD CEN/TS 16032:2010
  • BS EN 16075:2011 Fertilizers. Determination of N-(2-nitrophenyl) phosphoric triamide (2- NPT) in urea and fertilizers containing urea. Method using high performance liquid chromatography (HPLC)
  • BS EN 16079:2011 Founding. Compacted (vermicular) graphite cast irons
  • BS EN 16086-1:2011 Soil improvers and growing media. Determination of plant response. Pot growth test with Chinese cabbage
  • BS EN 16086-2:2011 Soil improvers and growing media. Determination of plant response. Petri dish test using cress
  • BS EN 16087-1:2011 Soil improvers and growing media. Determination of the aerobic biological activity. Oxygen uptake rate (OUR)
  • BS EN 16087-2:2011 Soil improvers and growing media. Determination of the aerobic biological activity. Self heating test for compost
  • BS EN 16090:2011 Copper and copper alloys. Estimation of average grain size by ultrasound
  • BS EN 16091:2011 (BS 2000-595:2011) Liquid petroleum products. Middle distillates and fatty acid methyl ester (FAME) fuels and blends. Determination of oxidation stability by rapid small scale oxidation method
  • BS EN 16109:2011 Fertilizers. Determination of complexed micronutrient ions in fertilizers. Identification of lignosulfonates
  • BS EN 16124:2011 Founding. Low-alloyed ferritic spheroidal graphite cast irons for elevated temperature applications
  • BS EN ISO 18113-2:2011 In vitro diagnostic medical devices. Information supplied by the manufacturer (labelling). In vitro diagnostic reagents for professional use
    Supersedes BS EN ISO 18113-2:2009
  • BS EN ISO 18113-3:2011 In vitro diagnostic medical devices. Information supplied by the manufacturer (labelling). In vitro diagnostic instruments for professional use
    Supersedes BS EN ISO 18113-3:2009
  • BS EN ISO 18113-4:2011 In vitro diagnostic medical devices. Information supplied by the manufacturer (labelling). In vitro diagnostic reagents for self-testing
    Supersedes BS EN ISO 18113-4:2009
  • BS EN ISO 18113-5:2011 In vitro diagnostic medical devices. Information supplied by the manufacturer (labelling). In vitro diagnostic instruments for self-testing
    Supersedes BS EN ISO 18113-5:2009
  • BS EN ISO 19011:2011 Guidelines for auditing management systems
    Supersedes BS EN ISO 19011:2002
  • BS EN ISO 20312:2011 Petroleum and natural gas industries. Design and operating limits of drill strings with aluminium alloy components
  • BS EN ISO 22432:2011 Geometrical product specifications (GPS). Features utilized in specification and verification
  • BS EN ISO 23936-2:2011 Petroleum, petrochemical and natural gas industries. Non-metallic materials in contact with media related to oil and gas production. Elastomers
  • BS EN ISO 28017:2011 Rubber hoses and hose assemblies, wire or textile reinforced, for dredging applications. Specification
    Supersedes BS ISO 28017:2009
  • BS EN ISO 30013:2011 Rubber and plastics hoses. Methods of exposure to laboratory light sources. Determination of changes in colour, appearance and other physical properties
    Supersedes BS EN ISO 11758:1997 and BS EN ISO 8580:1995
  • BS EN 50516-1-1:2011 Industrial connector sets and interconnect components to be used in optical fibre control and communication systems. Product specifications. Type SC-RJ PC industrial terminated on EN 60793-2-10 category A1a and A1b multimode fibre to meet the requirements of category I (industrial environments) as specified in IEC 61753-1-3
  • BS EN 50516-2-1:2011 Industrial connector sets and interconnect components to be used in optical fibre control and communication systems. Product specifications. Type ODVA PC industrial terminated on EN 60793-2-10 category A1a and A1b multimode fibre to meet the requirements of category I (industrial environments) as specified in EN 50173-1 and IEC 61753-1-3
  • BS EN 50533:2011 Railway applications. Three-phase train line voltage characteristics
  • BS EN 50563:2011 External A.C. D.C. and A.C. A.C. power supplies. Determination of no-load power and average efficiency of active modes
  • BS EN 60038:2011 CENELEC standard voltages
    Supersedes BS 7697:1993
  • BS EN 60068-2-83:2011 Environmental testing. Tests. Test Tf: Solderability testing of electronic components for surface mounting devices (SMD) by the wetting balance method using solder paste
  • BS EN 60068-3-1:2011 Environmental testing. Supporting documentation and guidance. Cold and dry heat tests
    Supersedes BS EN 60068-3-1:1999
  • BS EN 60076-1:2011 Power transformers. General
    Supersedes BS EN 60076-1:1997 which remains current
  • BS EN 60076-16:2011 Power transformers. Transformers for wind turbines applications
  • BS EN 60794-1-1:2011 Optical fibre cables. Generic specification. General
    Supersedes BS EN 60794-1-1:2002
  • BS EN 60929:2011 AC and/or DC-supplied electronic control gear for tubular fluorescent lamps. Performance requirements
    Supersedes BS EN 60925:1991 and BS EN 60929:2006 which remain current
  • BS EN 61347-2-3:2011 Lamp control gear. Particular requirements for A.C. and/or D.C. supplied electronic control gear for fluorescent lamps
    Supersedes BS EN 61347-2-3:2001+A2:2006, BS EN 61347-2-4:2001, BS EN 61347-2-5:2001 and BS EN 61347-2-6:2001 which remain current
  • BS EN 61386-25:2011 Conduit systems for cable management. Particular requirements. Conduit fixing devices
  • BS EN 61439-1:2011 Low-voltage switchgear and controlgear assemblies. General rules
    Supersedes BS EN 61439-1:2009 which remains current
  • BS EN 61439-2:2011 Low-voltage switchgear and controlgear assemblies. Power switchgear and controlgear assemblies
    Supersedes BS EN 61439-2:2009 which remains current
  • BS EN 61587-2:2011 Mechanical structures for electronic equipment. Tests for IEC 60917 and IEC 60297. Seismic tests for cabinets and racks
    Supersedes BS EN 61587-2:2001
  • BS EN 61850-7-1:2011 Communication networks and systems for power utility automation. Basic communication structure. Principles and models
    Supersedes BS EN 61850-7-1:2003
  • BS EN 61967-8:2011 Integrated circuits. Measurement of electromagnetic emissions. Measurement of radiated emissions. IC stripline method
  • BS EN 61970-301:2011 Energy management system application program interface (EMS-API). Common information model (CIM) base
    Supersedes BS EN 61970-301:2004
  • BS EN 62271-106:2011 High-voltage switchgear and controlgear. Alternating current contactors, contactor-based controllers and motor-starters
    Supersedes BS EN 60470:2001 which remains current
  • BS EN 62541-4:2011 OPC unified architecture. Services
  • BS EN 62541-5:2011 OPC unified architecture. Information model
  • BS EN 62541-6:2011 OPC unified architecture. Mappings
  • BS EN 62541-8:2011 OPC unified architecture. Data Access
  • BS EN 62561-6:2011 Lightning protection system components (LPSC). Requirements for lightning strike counters (LSC)
    Supersedes BS EN 50164-6:2009 which remains current

BS ENs implemented by amendment

  • BS EN ISO 8536-5:2011 Infusion equipment for medical use. Burette infusion sets for single use, gravity feed
    Implementation of European Standard EN ISO 8536-5 by amendment to BS ISO 8536-5:2004
  • PD CLC/TR 62662:2011 Guidance for production, testing and diagnostics of polymer insulators with respect to brittle fracture of core materials
    Implementation of European Standard CLC/TR 62662 by amendment to PD IEC/TR 62662:2010
  • PD CLC/TR 62685:2011 Industrial communication networks. Profiles. Assessment guideline for safety devices using IEC 61784-3 functional safety communication profiles (FSCPs)
    Implementation of European Standard CLC/TR 62685 by amendment to PD IEC/TR 62685:2010

BS implementations

BS Implementations comprise the ISO or IEC text without any national deviation and with front and back cover indicating the UK committee responsible. No other information will normally be added. The date referenced in the identifier is the date of the international standard.

  • BS ISO 124:2011 Latex, rubber. Determination of total solids content
    Supersedes BS ISO 124:2008
  • BS ISO 125:2011 Natural rubber latex concentrate. Determination of alkalinity
    Supersedes BS ISO 125:2003
  • BS ISO 132:2011 Rubber, vulcanized or thermoplastic. Determination of flex cracking and crack growth (De Mattia)
    Supersedes BS ISO 132:2005
  • BS ISO 248-1:2011 Rubber, raw. Determination of volatile-matter content. Hot-mill method and oven method
    Supersedes BS ISO 248:2005
  • BS ISO 254:2011 Belt drives. Pulleys. Quality, finish and balance
    Supersedes BS ISO 254:1998
  • BS ISO 776:2011 Pulps. Determination of acid-insoluble ash
    Supersedes BS 4496:1984
  • BS ISO 812:2011 Rubber, vulcanized or thermoplastic. Determination of low-temperature brittleness
    Supersedes BS ISO 812:2006
  • BS ISO 814:2011 Rubber, vulcanized or thermoplastic. Determination of adhesion to metal. Two-plate method
    Supersedes BS ISO 814:2007
  • BS ISO 1407:2011 Rubber. Determination of solvent extract
    Supersedes BS ISO 1407:2009
  • BS ISO 1827:2011 Rubber, vulcanized or thermoplastic. Determination of shear modulus and adhesion to rigid plates. Quadruple-shear methods
    Supersedes BS ISO 1827:2007
  • BS ISO 2493-2:2011 Paper and board. Determination of bending resistance. Taber-type tester
    Supersedes BS 3748:1992
  • BS ISO 2559:2011 Textile glass. Mats (made from chopped or continuous strands). Designation and basis for specifications
    Supersedes BS ISO 2559:2000
  • BS ISO 3065:2011 Oil of eucalyptus Australian type, containing a volume fraction of 80 % to 85 % of 1,8-cineole
  • BS ISO 3342:2011 Textile glass. Mats. Determination of tensile breaking force
    Supersedes BS ISO 3342:1995
  • BS ISO 3598:2011 Textile glass. Yarns. Basis for a specification
  • BS ISO 3972:2011 Sensory analysis. Methodology. Method of investigating sensitivity of taste
    Supersedes BS 5929-7:1992
  • BS ISO 4604:2011 Reinforcement fabrics. Determination of conventional flexural stiffness. Fixed-angle flexometer method
  • BS ISO 4664-1:2011 Rubber, vulcanized or thermoplastic. Determination of dynamic properties. General guidance
    Supersedes BS ISO 4664-1:2005
  • BS ISO 4900:2011 Textile glass. Mats and fabrics. Determination of contact mouldability
  • BS ISO 6101-6:2011 Rubber. Determination of metal content by atomic absorption spectrometry. Determination of magnesium content
  • BS ISO 6370-2:2011 Vitreous and porcelain enamels. Determination of the resistance to abrasion. Loss in mass after sub-surface abrasion
    Supersedes BS ISO 6370-2:1991
  • BS ISO 6469-3:2011 Electrically propelled road vehicles. Safety specifications. Protection of persons against electric shock
  • BS ISO 6666:2011 Coffee sampling. Triers for green coffee or raw coffee and parchment coffee
    Supersedes BS 6379-3:1983
  • BS ISO 7267-3:2011 Rubber-covered rollers. Determination of apparent hardness. Pusey and Jones method
    Supersedes BS ISO 7267-3:2007
  • BS ISO 7743:2011 Rubber, vulcanized or thermoplastic. Determination of compression stress-strain properties
    Supersedes BS ISO 7743:2008
  • BS ISO 7970:2011 Wheat (Triticum aestivum L.). Specification
    Supersedes the dual numbered standard BS ISO 7970:2000, BS 7274:2000
  • BS ISO 8082-2:2011 Self-propelled machinery for forestry. Laboratory tests and performance requirements for roll-over protective structures. Machines having a rotating platform with a cab and boom on the platform
  • BS ISO 8287:2011 Magnesium and magnesium alloys. Unalloyed magnesium. Chemical composition
  • BS ISO 9344:2011 Microscopes. Graticules for eyepieces
    Supersedes BS 7012-8:1997
  • BS ISO 10619-3:2011 Rubber and plastics hoses and tubing. Measurement of flexibility and stiffness. Bending tests at high and low temperatures
  • BS ISO/IEC 10746-2:2009 Information technology. Open distributed processing. Reference model: Foundations
    Supersedes BS ISO/IEC 10746-2:1996
  • BS ISO/IEC 10746-3:2009 Information technology. Open distributed processing. Reference model: Architecture
    Supersedes BS ISO/IEC 10746-3:1996
  • BS ISO 10784-2:2011 Space systems. Early operations. Initialization plan
  • BS ISO 11104:2011 Space data and information transfer systems. Time code formats
    Supersedes BS ISO 11104:2003
  • BS ISO 11262:2011 Soil quality. Determination of total cyanide
    Supersedes BS ISO 11262:2003
  • BS ISO 11452-4:2011 Road vehicles. Component test methods for electrical disturbances from narrowband radiated electromagnetic energy. Harness excitation methods
    Supersedes BS ISO 11452-4:2005
  • BS ISO 11783-4:2011 Tractors and machinery for agriculture and forestry. Serial control and communications data network. Network layer
  • BS ISO 11852:2011 Rubber. Determination of magnesium content of field and concentrated natural rubber latex by titration
  • BS ISO 12136:2011 Reaction to fire tests. Measurement of material properties using a fire propagation apparatus
  • BS ISO 12192:2011 Paper and board. Determination of compressive strength. Ring crush method
    Supersedes BS ISO 12192:2002
  • BS ISO 12670:2011 Thermal spraying. Components with thermally sprayed coatings. Technical supply conditions
  • BS ISO 12779:2011 Lactose. Determination of water content. Karl Fischer method
  • BS ISO 12830:2011 Paper, board and pulps. Determination of acid soluble magnesium, calcium, manganese, iron, copper, sodium and potassium
    Supersedes BS ISO 1830:2005, BS ISO 777:2005, BS ISO 778:2005 and BS ISO 779:2005
  • BS ISO 13209-1:2011 Road vehicles. Open test sequence eXchange format (OTX). General information and use cases
  • BS ISO 13289:2011 Recreational diving services. Requirements for the conduct of snorkelling excursions
  • BS ISO 13400-1:2011 Road vehicles. Diagnostic communication over internet protocol (DoIP). General information and use case definition
  • BS ISO 13887:2011 Cold-reduced steel sheet of higher yield strength with improved formability
    Supersedes BS ISO 13887:2004
  • BS ISO 13947:2011 Metallic powders. Test method for the determination of non-metallic inclusions in metal powders using a powder-forged specimen
    Supersedes BS ISO 13947:2007
  • BS ISO 14168:2011 Metallic powders, excluding hardmetals. Method for testing copper-base infiltrating powders
    Supersedes BS ISO 14168:2003
  • BS ISO 14380:2011 Water quality. Determination of the acute toxicity to Thamnocephalus platyurus (Crustacea, Anostraca)
  • BS ISO 14490-8:2011 Optics and optical instruments. Test methods for telescopic systems. Test methods for night vision devices
  • BS ISO 15042:2011 Multiple split-system air-conditioners and air-to-air heat pumps. Testing and rating for performance
  • BS ISO 15063:2011 Plastics. Polyols for use in the production of polyurethanes. Determination of hydroxyl number by NIR spectroscopy
  • BS ISO/IEC/IEEE 15289:2011 Systems and software engineering. Content of life-cycle information products (documentation)
    Supersedes BS ISO/IEC 15289:2006
  • BS ISO 15765-2:2011 Road vehicles. Diagnostic communication over controller area network (DoCAN). Transport protocol and network layer services
  • BS ISO 16000-3:2011 Indoor air. Determination of formaldehyde and other carbonyl compounds in indoor air and test chamber air. Active sampling method
    Supersedes BS ISO 16000-3:2001
  • BS ISO 16000-4:2011 Indoor air. Determination of formaldehyde. Diffusive sampling method
    Supersedes BS ISO 16000-4:2004
  • BS ISO 16242:2011 Surface chemical analysis. Recording and reporting data in Auger electron spectroscopy (AES)
  • BS ISO 16243:2011 Surface chemical analysis. Recording and reporting data in X-ray photoelectron spectroscopy (XPS)
  • BS ISO 16873:2011 Hydraulic fluid power. Pressure switches. Mounting surfaces
    Supersedes BS ISO 16873:2002
  • BS ISO 17107:2011 Space data and information transfer systems. XML specification for navigation data messages
  • BS ISO 18186:2011 Freight containers. RFID cargo shipment tag system
  • BS ISO 18941:2011 Imaging materials. Colour reflection prints. Test method for ozone gas fading stability
  • BS ISO 19149:2011 Geographic information. Rights expression language for geographic information. GeoREL
  • BS ISO/IEC 19757-11:2011 Information technology. Document schema definition languages (DSDL). Schema association
  • BS ISO/IEC 19794-5:2011 Information technology. Biometric data interchange formats. Face image data
    Supersedes BS ISO/IEC 19794-5:2005+A2:2009
  • BS ISO 22671:2011 Space data and information transfer systems. Space link extension (SLE). Forward communications link transmission unit (CLTU) service
    Supersedes BS ISO 22671:2007
  • BS ISO 22672:2011 Space data and information transfer systems. Space link extension (SLE). Forward space packet service specification
    Supersedes BS ISO 22672:2006
  • BS ISO 22915-11:2011 Industrial trucks. Verification of stability. Industrial variable-reach trucks
    Supersedes BS ISO 13562-1:2000
  • BS ISO 23559:2011 Plastics. Film and sheeting. Guidance on the testing of thermoplastic films
    Supersedes BS ISO 23559:2007
  • BS ISO 23611-5:2011 Soil quality. Sampling of soil invertebrates. Sampling and extraction of soil macroinvertebrates
  • BS ISO/IEC 24789-2:2011 Identification cards. Card service life. Methods of evaluation
  • BS ISO 26262-1:2011 Road vehicles. Functional safety. Vocabulary
  • BS ISO 26262-2:2011 Road vehicles. Functional safety. Management of functional safety
  • BS ISO 26262-3:2011 Road vehicles. Functional safety. Concept phase
  • BS ISO 26262-4:2011 Road vehicles. Functional safety. Product development at the system level
  • BS ISO 26262-5:2011 Road vehicles. Functional safety. Product development at the hardware level
  • BS ISO 26262-6:2011 Road vehicles. Functional safety. Product development at the software level
  • BS ISO 26262-7:2011 Road vehicles. Functional safety. Production and operation
  • BS ISO 26262-8:2011 Road vehicles. Functional safety. Supporting processes
  • BS ISO 26262-9:2011 Road vehicles. Functional safety. Automotive safety integrity level (ASIL)-oriented and safety oriented analyses
  • BS ISO/IEC 27007:2011 Information technology. Security techniques. Guidelines for information security management systems auditing
  • BS ISO/IEC 27034-1:2011 Information technology. Security techniques. Application security. Overview and concepts
  • BS ISO/IEC 29100:2011 Information technology. Security techniques. Privacy framework
  • BS ISO/IEC/IEEE 29148:2011 Systems and software engineering. Life cycle processes. Requirements engineering
  • BS ISO 30300:2011 Information and documentation. Management systems for records. Fundamentals and vocabulary
  • BS ISO 30301:2011 Information and documentation. Management systems for records. Requirements

Publicly available specifications

Publicly Available Specifications (formerly Product Assessment Specifications) are issued to provide an interim document where there is a market need but where a full Standard has yet to be published.

  • PAS 81:2011 Specification for the management of a swimming school
    Supersedes PAS 81:2008
  • PAS 95:2011 Hypoxic air fire prevention systems. Specification
  • PAS 98-1:2011 Standards consortia. Formation and management. A good practice guide
  • PAS 98-2:2011 Standards consortia. Suitability assessment. A good practice guide

Corrigenda to British Standards and updated British Standards

Most British amendments are not issued separately. Those that make significant changes to a standard are incorporated into the standard which is re-issued as a new edition. All amendments to date of despatch are included within any main publication when ordered for the first time. The following amended Standards and corrigenda to British Standards were made available last month.

  • BS 1339-2:2009 (CD-ROM) Humidity. Humidity calculation functions, tables and user guide
    CORRIGENDUM 1
  • BS 4662:2006+A1:2009 Boxes for flush mounting of electrical accessories. Requirements, test methods and dimensions
    CORRIGENDUM 2
  • BS 4978:2007+A1:2011 Visual strength grading of softwood. Specification
    AMENDMENT 1
  • BS 5756:2007+A1:2011 Visual strength grading of hardwood. Specification
    AMENDMENT 1
  • BS EN 1168:2005+A3:2011 Precast concrete products. Hollow core slabs
    AMENDMENT 3
  • BS EN 1998-2:2005+A2:2011 Eurocode 8. Design of structures for earthquake resistance. Bridges
    AMENDMENT 2
  • BS EN 1999-1-3:2007+A1:2011 Eurocode 9. Design of aluminium structures. Structures susceptible to fatigue
    AMENDMENT 1
  • BS EN 1999-1-4:2007+A1:2011 Eurocode 9. Design of aluminium structures. Cold-formed structural sheeting
    AMENDMENT 1
  • BS EN 3034:2009 Aerospace series. Nuts, self-locking, hexagonal with captive washer. In heat resisting steel FEPA92HT (A286), silver coated. Classification: 1100 MPa/425°C
    CORRIGENDUM 1
  • BS EN 3687:2010 Aerospace series. Bolts, normal hexagon head, relieved shank, long thread, in heat resisting steel FE-PA2601 (A286), silver plated. Classification: 1100 MPa/650°C
    CORRIGENDUM 1
  • BS EN ISO 4671:2007+A1:2011 Rubber and plastics hoses and hose assemblies. Methods of measurement of the dimensions of hoses and the lengths of hose assemblies
    AMENDMENT 1
  • BS EN ISO 5173:2010+A1:2011 Destructive tests on welds in metallic materials. Bend tests
    AMENDMENT 1
  • BS EN ISO 7380-1:2011 Button head screws. Hexagon socket button head screws
    CORRIGENDUM 1
  • BS EN ISO 7380-2:2011 Button head screws. Hexagon socket button head screws with collar
    CORRIGENDUM 1
  • BS EN ISO 8536-5:2011 Infusion equipment for medical use. Burette infusion sets for single use, gravity feed
    CORRIGENDUM 1
  • BS EN ISO 12137:2011 Paints and varnishes. Determination of mar resistance
    CORRIGENDUM 1
  • BS EN 12390-3:2009 Testing hardened concrete. Compressive strength of test specimens
    CORRIGENDUM 1
  • BS EN 12409:2008+A1:2011 Plastics and rubber machines. Thermoforming machines. Safety requirements
    AMENDMENT 1
  • BS EN 13145:2001+A1:2011 Railway applications. Track. Wood sleepers and bearers
    AMENDMENT 1
  • BS EN 13232-2:2003+A1:2011 Railway applications. Track. Switches and crossings. Requirements for geometric design
    AMENDMENT 1
  • BS EN 13232-3:2003+A1:2011 Railway applications. Track. Switches and crossings. Requirements for wheel/rail interaction
    AMENDMENT 1
  • BS EN 13232-4:2005+A1:2011 Railway applications. Track. Switches and crossings. Actuation, locking and detection
    AMENDMENT 1
  • BS EN 13232-5:2005+A1:2011 Railway applications. Track. Switches and crossings. Switches
    AMENDMENT 1
  • BS EN 13232-6:2005+A1:2011 Railway applications. Track. Switches and crossings. Fixed common and obtuse crossings
    AMENDMENT 1
  • BS EN 13232-7:2006+A1:2011 Railway applications. Track. Switches and crossings. Crossings with moveable parts
    AMENDMENT 1
  • BS EN 13232-8:2007+A1:2011 Railway applications. Track. Switches and crossings. Expansion devices
    AMENDMENT 1
  • BS EN 13232-9:2006+A1:2011 Railway applications. Track. Switches and crossings. Layouts
    AMENDMENT 1
  • BS EN 13420:2011 Windows. Behaviour between different climates. Test method
    CORRIGENDUM 1
  • BS EN 13480-8:2007 Metallic industrial piping. Additional requirements for aluminium and aluminium alloy piping
    CORRIGENDUM 1
  • BS EN 14033-3:2009+A1:2011 Railway applications. Track. Railbound construction and maintenance machines. General safety requirements
    AMENDMENT 1
  • BS EN 15102:2007+A1:2011 Decorative wall coverings. Roll and panel form
    AMENDMENT 1
  • BS EN 15194:2009+A1:2011 Cycles. Electrically power assisted cycles. EPAC Bicycles
    AMENDMENT 1
  • BS EN 15632-2:2010 District heating pipes. Pre-insulated flexible pipe systems. Bonded plastic service pipes. Requirements and test methods
    CORRIGENDUM 1
  • BS EN 15632-3:2010 District heating pipes. Pre-insulated flexible pipe systems. Non bonded system with plastic service pipes; requirements and test methods
    CORRIGENDUM 1
  • BS EN 15746-1:2010+A1:2011 Railway applications. Track. Road-rail machines and associated equipment. Technical requirements for running and working
    AMENDMENT 1
  • BS EN 15746-2:2010+A1:2011 Railway applications. Track. Road-rail machines and associated equipment. General safety requirements
    AMENDMENT 1
  • BS EN ISO 15792-1:2008+A1:2011 Welding consumables. Test methods. Test methods for all-weld metal test specimens in steel, nickel and nickel alloys
    AMENDMENT 1
  • BS EN ISO 18113-1:2011 In vitro diagnostic medical devices. Information supplied by the manufacturer (labelling). Terms, definitions and general requirements
    CORRIGENDUM 1
  • BS EN ISO 18113-2:2011 In vitro diagnostic medical devices. Information supplied by the manufacturer (labelling). In vitro diagnostic reagents for professional use
    CORRIGENDUM 1
  • BS EN ISO 18113-4:2011 In vitro diagnostic medical devices. Information supplied by the manufacturer (labelling). In vitro diagnostic reagents for self-testing
    CORRIGENDUM 1
  • BS EN ISO 18113-5:2011 In vitro diagnostic medical devices. Information supplied by the manufacturer (labelling). In vitro diagnostic instruments for self-testing
    CORRIGENDUM 1
  • BS EN ISO 19131:2008+A1:2011 Geographic information. Data product specifications
    AMENDMENT 1
  • BS EN ISO 22434:2011 Transportable gas cylinders. Inspection and maintenance of cylinder valves
    CORRIGENDUM 2
  • BS EN 26801:1993+A1:2011 Rubber and plastics hoses. Determination of volumetric expansion
    AMENDMENT 1
  • BS EN 50085-2-1:2006+A1:2011 Cable trunking systems and cable ducting systems for electrical installations. Cable trunking systems and cable ducting systems intended for mounting on walls and ceilings
    AMENDMENT 1
  • BS EN 50149:2001 Railway applications. Fixed installations. Electric traction. Copper and copper alloy grooved contact wires
    CORRIGENDUM 5
  • BS EN 50363-3:2005+A1:2011 Insulating, sheathing and covering materials for low voltage energy cables. PVC insulating compounds
    CORRIGENDUM 1
  • BS EN 50363-5:2005+A1:2011 Insulating, sheathing and covering materials for low voltage energy cables. Halogen-free, crosslinked insulating compounds
    AMENDMENT 1
  • BS EN 50363-6:2005+A1:2011 Insulating, sheathing and covering materials for low voltage energy cables. Halogen-free, crosslinked sheathing compounds
    AMENDMENT 1
  • BS EN 50363-8:2005+A1:2011 Insulating, sheathing and covering materials for low voltage energy cables. Halogen-free, thermoplastic sheathing compounds
    AMENDMENT 1
  • BS EN 50400:2006 Basic standard to demonstrate the compliance of fixed equipment for radio transmission (110 MHz – 40 GHz) intended for use in wireless telecommunication networks with the basic restrictions or the reference levels related to general public exposure to radio frequency electromagnetic fields, when put into service
    CORRIGENDUM 1
  • BS EN 50401:2006+A1:2011 Product standard to demonstrate the compliance of fixed equipment for radio transmission (110 MHz – 40 GHz) intended for use in wireless telecommunication networks with the basic restrictions or the reference levels related to general public exposure to radio frequency electromagnetic fields, when put into service
    AMENDMENT 1
  • BS EN 50408:2008+A1:2011 Household and similar electrical appliances. Safety. Particular requirements for cab heaters for vehicles
    AMENDMENT 1
  • BS EN 50464-4:2007+A1:2011 Three-phase oil-immersed distribution transformers 50 Hz, from 50 kVA to 2500 kVA with highest voltage for equipment not exceeding 36 kV. Requirements and tests concerning pressurised corrugated tanks
    AMENDMENT 1
  • BS EN 55014-2:1997+A2:2008 (CISPR 14-2:1997) Electromagnetic compatibility. Requirements for household appliances, electric tools and similar apparatus. Immunity. Product family standard
    CORRIGENDUM 3
  • BS EN 55016-1-1:2010+A1:2010 Specification for radio disturbance and immunity measuring apparatus and methods. Radio disturbance and immunity measuring apparatus. Measuring apparatus
    CORRIGENDUM 1
  • BS EN 55020:2007+A11:2011 Sound and television broadcast receivers and associated equipment. Immunity characteristics. Limits and methods of measurement
    AMENDMENT 11
  • BS EN 55022:2010 Information technology equipment. Radio disturbance characteristics. Limits and methods of measurement
    CORRIGENDUM 1
  • BS EN 60061-1:1993+A46:2011 Lamp caps and holders together with gauges for the control of interchangeability and safety. Lamp caps
    AMENDMENT 46
  • BS EN 60061-4:1992+A13:2011 Lamp caps and holders together with gauges for the control of interchangeability and safety. Guidelines and general information
    AMENDMENT 13
  • BS EN 60065:2002+A12:2011 Audio, video and similar electronic apparatus. Safety requirements
    CORRIGENDUM 3
  • BS EN 60335-2-35:2002+A2:2011 Household and similar electrical appliances. Safety. Particular requirements for instantaneous water heaters
    AMENDMENT 2
  • BS EN 60947-4-3:2000+A2:2011 Low-voltage switchgear and controlgear. Contactors and motor-starters. AC semiconductor controllers and contactors for non-motor loads
    AMENDMENT 2
  • BS EN 61000-4-7:2002+A1:2009 Electromagnetic compatibility (EMC). Testing and measurement techniques. General guide on harmonics and interharmonics measurements and instrumentation, for power supply systems and equipment connected thereto
    CORRIGENDUM 3
  • BS EN 61937-1:2007+A1:2011 Digital audio. Interface for non-linear PCM encoded audio bitstreams applying IEC 60958. General
    AMENDMENT 1
  • BS EN 62002-1:2008 Mobile and portable DVB-T/H radio access. Interface specification
    CORRIGENDUM 1
  • BS EN 62115:2005+A2:2011 Electric toys. Safety
    CORRIGENDUM 2
  • BS EN 62271-102:2002+A1:2011 High-voltage switchgear and controlgear. Alternating current disconnectors and earthing switches
    AMENDMENT 1
  • PD CLC/TR 62662:2011 Guidance for production, testing and diagnostics of polymer insulators with respect to brittle fracture of core materials
    CORRIGENDUM 1
  • BS EN 80416-3:2002+A1:2011 Basic principles for graphical symbols for use on equipment. Guidelines for the application of graphical symbols
    AMENDMENT 1
  • BS ISO 10243:2010+A1:2011 Tools for pressing. Compression springs with rectangular section. Housing dimensions and colour coding
    AMENDMENT 1
  • BS ISO 15930-8:2010 Graphic technology. Prepress digital data exchange using PDF. Partial exchange of printing data using PDF 1.6 (PDF/X-5)
    CORRIGENDUM 1
  • BS ISO/IEC 19794-4:2005 Information technology. Biometric data interchange formats. Finger image data
    CORRIGENDUM 1
  • PD CLC/TR 62685:2011 Industrial communication networks. Profiles. Assessment guideline for safety devices using IEC 61784-3 functional safety communication profiles (FSCPs)
    CORRIGENDUM 1
  • BS A 314:1997 (ISO 9609:1996) Aerospace. Nuts, hexagonal, plain, reduced height, normal across flats, with MJ threads, classifications: 450 MPa (at ambient temperature)/120°C, 450 MPa (at ambient temperature)/235°C, 600 MPa (at ambient temperature)/425°C, 900 MPa (at ambient temperature)/235°C, 900 MPa (at ambient temperature)/315°C, 900 MPa (at ambient temperature)/650°C, 1100 MPa (at ambient temperature)/235°C, 1100 MPa (at ambient temperature)/730°C and 1250 MPa (at ambient temperature)/600°C. Dimensions
    CORRIGENDUM 1

British Standards declared obsolescent

Declaration of obsolescence indicates that the standard is not recommended for use in new equipment but needs to be retained for the servicing of existing equipment that is expected to have a long working life.

  • BS 11:1985 Specification for railway rails
    This standard has been declared obsolescent but it allows for the repairs and maintenance of existing track, and gives profile descriptions for supply of rails (particularly 95-lb/yd bullhead) not within the scope of BS EN 13674
  • BS 519:1950 Specification for tractive armature direct current neutral-polar line relays for railway signalling
    This standard has been declared obsolescent after having been reviewed by the committee, it is no longer felt relevant
  • BS 561:1951 Specification for alternating-current line relays double-element 3-position (for railway signalling)
    This standard has been declared obsolescent after having been reviewed by the committee, it is no longer felt relevant
  • BS 812-105.1:1989 Testing aggregates. Methods for determination of particle shape. Flakiness index
    This standard has been declared obsolescent as it is no longer relevant. It is replaced by BS EN 33-3:1997
  • BS 812-110:1990 Testing aggregates. Methods for determination of aggregate crushing value (ACV)
    This standard has been declared obsolescent as it is no longer relevant. It is partially replaced by BS EN 1097-2:1998
  • BS 812-111:1990 Testing aggregates. Methods for determination of ten per cent fines value (TFV)
    This standard has been declared obsolescent as it is no longer relevant. It is partially replaced by BS EN 1097-2:1998
  • BS 812-112:1990 Testing aggregates. Method for determination of aggregate impact value (AIV)
    This standard has been declared obsolescent as it is no longer relevant. It is partially replaced by BS EN 1097-2:1998
  • BS 812-119:1985 Testing aggregates. Method for determination of acid-soluble material in fine aggregate
    This standard has been declared obsolescent as it is no longer relevant. It is replaced by BS EN 1744-1:1998
  • BS 903-1:1995 Physical testing of rubber. Guide to the selection and use of methods of test for rubber
    This standard has been declared obsolescent after having been reviewed by the committee, it is no longer felt relevant
  • BS 903-A9:1988 Physical testing of rubber. Determination of abrasion resistance
    This standard has been declared obsolescent after having been reviewed by the committee, it is no longer felt relevant. It is partially replaced by BS ISO 4649:2002
  • BS 1113:1999 Specification for design and manufacture of water-tube steam generating plant (including superheaters, reheaters and steel tube economizers)
    This standard has been declared obsolescent after having been reviewed by the committee, it is no longer felt relevant. It is replaced by BS EN 12952-1:2001, BS EN 12952-2:2001, BS EN 12952-3:2001, BS EN 12952-5:2001, BS EN 12952-6:2002, BS EN 12952-7:2002, BS EN 12952-10:2002 and BS EN 12952-11:2007
  • BS 1199 and 1200:1976 Specifications for building sands from natural sources
    This standard has been declared obsolescent after having been reviewed by the committee, it is no longer felt relevant. It is replaced by BS EN 13139:2002
  • BS 1210:1963 Specification for wood screws
    This standard has been re-declared obsolescent for a further period as it is no longer relevant
  • BS 1782:1951 Specification for couplings for suction and delivery hose (11?2 in. to 8 in. nominal sizes) other than fire hose couplings
    This standard has been re-declared obsolescent for a further period as it is no longer relevant
  • BS 1892-1:1986 Gymnasium equipment. Specification of general requirements
    This standard has been declared obsolescent after having been reviewed by the committee, it is no longer felt relevant. It is partially replaced by BS EN 913:1996
  • BS 1906:1952 Specification for hose couplings (air and water) (1?8 in. to 11?4 in. nominal sizes)
    This standard has been re-declared obsolescent for a further period as it is no longer relevant
  • BS 2050:1978 Specification for electrical resistance of conducting and antistatic products made from flexible polymeric material
    This standard has been declared obsolescent after having been reviewed by the committee, it is no longer felt relevant. It is partially replaced by BS ISO 2878:2005
  • BS 2464:1954 Specification for hose couplings for petrol, oil and lubricants (3?4 in. to 4 in. nominal sizes)
    This standard has been re-declared obsolescent for a further period as it is no longer relevant
  • BS 2464-2:1969 Specification for hose couplings for petrol, oil and lubricants. High pressure couplings
    This standard has been re-declared obsolescent for a further period as it is no longer relevant
  • BS 2523:1966 Specification for lead-based priming paints
    This standard has been declared obsolescent after having been reviewed by the committee, it is no longer felt relevant. It is partially replaced by BS 5082:1974 and BS 5358:1976
  • BS 2606:1955 Specification for X-ray protective gloves for medical diagnostic purposes up to 150 kV peak
    This standard has been declared obsolescent after having been reviewed by the committee, it is no longer felt relevant
  • BS 2655-1:1970 Specification for lifts, escalators, passenger conveyors and paternosters. General requirements for electric, hydraulic and hand powered lifts
    This standard has been re-declared obsolescent for a further period as it is still being used during lift modernization. It is partially replaced by Parts 1, 2, 3 and 14 of BS 5655
  • BS 2655-4:1969 Specification for lifts, escalators, passenger conveyors and paternosters. General requirements for escalators and passenger conveyors
    This standard has been re-declared obsolescent for a further period as it is still being used during lift modernisation. It is replaced by BS 5656:1983
  • BS 2655-5:1970 Specification for lifts, escalators, passenger conveyors and paternosters. General requirements for paternosters
    This standard has been re-declared obsolescent for a further period as it is still being used during lift modernisation
  • BS 2655-6:1970 Specification for lifts, escalators, passenger conveyors and paternosters. Building construction requirements
    This standard has been re-declared obsolescent for a further period as it is still being used during lift modernisation. It is partially replaced by Parts 1, 2, 3 and 14 of BS 5655
  • BS 2655-7:1970 Specification for lifts, escalators, passenger conveyors and paternosters. Testing and inspection
    This standard has been re-declared obsolescent for a further period as it is still being used during lift modernisation. It is partially replaced by BS 5655-1:1979 and BS 5655-10:1986
  • BS 2655-8:1971 Specification for lifts, escalators, passenger conveyors and paternosters. Modernization or reconstruction of lifts, escalators and paternosters
    This standard has been re-declared obsolescent for a further period as it is still being used during lift modernisation. It is partially replaced by Parts 1, 11 and 12 of BS 5655
  • BS 2655-9:1970 Specification for lifts, escalators, passenger conveyors and paternosters. Definitions
    This standard has been re-declared obsolescent for a further period as it is still being used during lift modernisation
  • BS 2655-10:1972 Specification for lifts, escalators, passenger conveyors and paternosters. General requirements for guarding
    This standard has been re-declared obsolescent for a further period as it is still being used during lift modernization. It is partially replaced by BS 5655-1:1979, BS 5655:Part 6:1985 and BS 5656:1983
  • BS 2782-4:Method 434B:1977 Methods of testing plastics. Chemical properties. Determination of antioxidants in polyolefin compounds by ultra-violet absorption of the chloroform extract
    This standard has been re-declared obsolescent for a further period as it is no longer relevant
  • BS 2782-5:Method 540C:1988 Methods of testing plastics. Optical and colour properties, weathering. Determination of ultraviolet radiation intensity using polysulphone film
    This standard has been declared obsolescent as it is no longer relevant
  • BS 2952:1958 Specification for rubber hose for i.c. engine cooling systems
    This standard has been re-declared obsolescent for a further period as it is no longer relevant
  • BS 3062:1985 Specification for ophthalmic lens materials
    This standard has been declared obsolescent after having been reviewed by the committee, it is no longer felt relevant
  • BS 3347:1961 Specification for capacitors for railway signalling track circuits
    This standard has been declared obsolescent after having been reviewed by the committee, it is no longer felt relevant
  • BS 3783:1964 Specification for X-ray lead-rubber protective aprons for personal use
    This standard has been declared obsolescent after having been reviewed by the committee, it is no longer felt relevant
  • BS 3900-B3:1983 Methods of test for paints. Tests involving chemical examination of liquid paints and dried paint films. Determination of 'soluble' lead in the solid matter in liquid paints: method for use in conjunction with The Control of Lead at Work Regulations, 1980
    This standard has been declared obsolescent after having been reviewed by the committee, it is no longer felt relevant
  • BS 3970-1:1990 Sterilizing and disinfecting equipment for medical products. Specification for general requirements
    This standard has been declared obsolescent after having been reviewed by the committee, it is no longer felt relevant. It is partially replaced by BS EN 285:1997, BS EN 1422:1997+A1:2009 and BS EN 61010-2-043:1998
  • BS 4031:1966 Specification for X-ray protective lead glasses
    This standard has been declared obsolescent after having been reviewed by the committee, it is no longer felt relevant
  • BS 5051-1:1988 Bullet-resistant glazing. Specification for glazing for interior use
    This standard has been declared obsolescent after having been reviewed by the committee, it is no longer felt relevant. It is replaced by BS EN 1063:2000
  • BS 5446-3:2005 Fire detection and fire alarm devices for dwellings. Specification for smoke alarm kits for deaf and hard of hearing people
    This standard has been declared obsolescent after having been reviewed by the committee, it is no longer felt relevant
  • BS 5544:1978 Specification for anti-bandit glazing (glazing resistant to manual attack)
    This standard has been declared obsolescent after having been reviewed by the committee, it is no longer felt relevant. It is replaced by BS EN 356:2000 for the testing and classification of glass and glass/plastics composites but remains available for the testing and classification of plastics glazing sheet materials until a corresponding British Standard is published for these
  • BS 5655-7:1983 Lifts and service lifts. Specification for manual control devices, indicators and additional fittings
    This standard has been declared obsolescent as it is no longer relevant. It is replaced by BS EN 81-70, which is a Harmonised Standard under the Lifts Directive
  • BS 5655-9:1985 Lifts and service lifts. Specification for guide rails
    This standard has been declared obsolescent as it is no longer relevant. It is replaced by Annex G of BS EN 81-1 and Annex G of BS EN 81-2, both of which are Harmonised Standards under the Lifts Directive
  • BS 5655-13:1995 Lifts and service lifts. Recommendations for vandal resistant lifts
    This standard has been re-declared obsolescent for a further period as it is still being used during lift modernization. It is replaced by BS EN 81-71
  • BS 6166-3:1988 Lifting slings. Guide to the selection and safe use of lifting slings for multi-purposes
    This standard has been declared obsolescent after having been reviewed by the committee, it is no longer felt relevant
  • BS 6485:1999 PVC-covered conductors for overhead power lines
    This standard has been declared obsolescent after having been reviewed by the committee, it is no longer felt relevant
  • BS 6807:1986 Methods of test for the ignitability of mattresses with primary and secondary sources of ignition
    This standard has been declared obsolescent as it is Superseded by BS 6807:1990. BS 6807:1986 was withdrawn in error, and has now been reinstated on the grounds that it is cited in legislation
  • BS 7254-6.2:1990 Orthopaedic implants. Forgings. Method for specifying forgings
    This standard has been declared obsolescent after having been reviewed by the committee, it is no longer felt relevant
  • BS 7870-6.1:1999 LV and MV polymeric insulated cables for use by distribution and generation utilities. Specification for 0.6/1 kV and 1.9/3.3 kV power cables with special fire performance for use in power stations. PVC insulated and PVC sheathed cables
    This standard has been declared obsolescent after having been reviewed by the committee, it is no longer felt relevant
  • BS 7870-6.2:1999 LV and MV polymeric insulated cables for use by distribution and generation utilities. Specification for 0.6/1 kV and 1.9/3.3 kV power cables with special fire performance for use in power stations XLPE or HEPR insulated and PVC sheathed cables
    This standard has been declared obsolescent after having been reviewed by the committee, it is no longer felt relevant
  • BS 7870-6.3:1999 LV and MV polymeric insulated cables for use by distribution and generation utilities. Specification for 0.6/1 kV and 1.9/3.3 kV power cables with special fire performance for use in power stations. Cables with thermosetting insulation and non-halogenated sheath
    This standard has been declared obsolescent after having been reviewed by the committee, it is no longer felt relevant
  • BS AU 194:1984 Specification for performance of electrical connections between towing vehicles and trailers
    This standard has been declared obsolescent after having been reviewed by the committee, it is no longer felt relevant
  • BS AU 196:1984 Specification for electrical connections between 24 V trailer antilock braking systems and towing vehicles
    This standard has been declared obsolescent after having been reviewed by the committee, it is no longer felt relevant
  • BS V 38:1967 Specification for Sitka spruce as rough timber
    This standard has been re-declared obsolescent for a further period as after having been reviewed by the committee, it is no longer felt relevant
  • BS 2V 35:1966 Specification for plywood for aeronautical purposes
    This standard has been re-declared obsolescent for a further period as after having been reviewed by the committee, it is no longer felt relevant
  • BS 2V 37:1968 Specification for Sitka spruce as finished timber
    This standard has been re-declared obsolescent for a further period after having been reviewed by the committee, it is no longer felt relevant
  • BS 3V 4:1929 Specification for aircraft material. Ash
    This standard has been re-declared obsolescent for a further period as after having been reviewed by the committee, it is no longer felt relevant
  • BS 6V 3:1943 Specification for aircraft material. High strength plywood for aircraft
    This standard has been re-declared obsolescent for a further period as after having been reviewed by the committee, it is no longer felt relevant
  • BS 6W 8:1938 Tie rods (swaged) (No. 4 B.A. to 1?2 inch B.S.F. inclusive) for aircraft purposes
    This standard has been declared obsolescent as it is no longer relevant
  • BS 2PL 1:1966 Specification for phenolic mouldings for aeronautical purposes
    This standard has been re-declared obsolescent for a further period, as after having been reviewed by the committee, it is no longer felt relevant
  • BS SP 53:1953 Specification for swaged cable-end assemblies (B.A. and B.S.F. threads) for preformed steel wire rope for aircraft (suitable for use with British Standard W.9 wire rope)
    This standard has been declared obsolescent as it is no longer relevant
  • BS SP 118:1958 Tie rods (Unified threads) for aircraft
    This standard has been declared obsolescent as it is no longer relevant
  • BS 2SP 105:1955 Specification for swaged cable-end assemblies (Unified threads) for preformed steel wire rope (W.9) for aircraft
    This standard has been declared obsolescent as it is no longer relevant
  • BS 3SP 3:1943 Specification for aircraft material. Fork joints (low tensile type) (for sizes No. 4 B.A. to 1?2 inch B.S.F. inclusive)
    This standard has been re-declared obsolescent for a further period as after having been reviewed by the committee, it is no longer felt relevant

British Standards withdrawn

  • BS 534:1990 Specification for steel pipes, joints and specials for water and sewage
    Superseded by BS EN 10224:2002 and BS EN 10311:2005
  • BS 544:1969 Specification for linseed oil putty for use in wooden frames
    This standard has been withdrawn as it is no longer used
  • BS 638-5:1988 Arc welding power sources, equipment and accessories. Specification for accessories
    Superseded by BS EN 60974-5:2002, BS EN 60974-12:1996 and BS EN 60974-13:2011
  • BS 648:1964 Schedule of weights of building materials
    This standard has been withdrawn as it was the primary source of data for use with BS 6399. BS 6399 is now superseded by Eurocode BS EN 1991-1-1 and withdrawn. The committee will continue to review BS 648 for any content that may need to be retained as NCCI for use with BS EN 1991-1-1
  • BS 684-1.12:1990 (ISO 8293:1990) Methods of analysis of fats and fatty oils. Physical methods. Determination of dilatation
    This standard has been withdrawn as it is identical to ISO 8293:1990 which has been withdrawn by ISO/TC 34/SC 11
  • BS 684-2.44:1984 (ISO 6464:1983) Methods of analysis of fats and fatty oils. Other methods. Determination of gallates
    This standard has been withdrawn as it is identical to ISO 6464:1983 which has been withdrawn by ISO/TC 34/SC 11
  • BS 812-100:1990 Testing aggregates. General requirements for apparatus and calibration
    Superseded by BS EN 932-5:2000
  • BS 812-101:1984 Testing aggregates. Guide to sampling and testing aggregates
    Superseded by BS EN 932-6:1999
  • BS 812-102:1989 Testing aggregates. Methods for sampling
    Superseded by BS EN 932-1:1997
  • BS 812-103.1:1985 Testing aggregates. Method for determination of particle size distribution. Sieve tests
    Superseded by BS EN 933-1:1997
  • BS 812-106:1985 Testing aggregates. Method for determination of shell content in coarse aggregate
    Superseded by BS EN 933-7:1998
  • BS 812-113:1990 Testing aggregates. Method for determination of aggregate abrasion value (AAV)
    Superseded by BS EN 1097-8:2000
  • BS 812-117:1988 Testing aggregates. Method for determination of water-soluble chloride salts
    Superseded by BS EN 1744-1:1998
  • BS 812-118:1988 Testing aggregates. Methods for determination of sulphate content
    Superseded by BS EN 1744-1:1998
  • BS 812-120:1989 Testing aggregates. Method for testing and classifying drying shrinkage of aggregates in concrete
    Superseded by BS EN 1367-4:1998
  • BS 864-2:1983 Capillary and compression tube fittings of copper and copper alloy. Specification for capillary and compression fittings for copper tubes
    Superseded by BS EN 1254-1:1998 and BS EN 1254-2:1998
  • BS 864-5:1990 Capillary and compression tube fittings of copper and copper alloy. Specification for compression fittings for polyethylene pipes with outside diameters to BS 5556
    Superseded by BS EN 1254-3:1998
  • BS 1179:1967 Glossary of terms used in the gas industry
    Superseded by BS 1179-6:1980
  • BS 1453:1972 Specification for filler materials for gas welding
    Superseded by BS EN 12536:2000
  • BS 1747-1:1969 Methods for the measurement of air pollution. Deposit gauges
    This standard has been withdrawn as it conflicts with new European standards
  • BS 1747-2:1969 Methods for the measurement of air pollution. Determination of concentration of suspended matter
    This standard has been withdrawn as it conflicts with new European standards
  • BS 1747-3:1969 Methods for measurement of air pollution. Determination of sulphur dioxide
    This standard has been withdrawn as it conflicts with new European standards
  • BS 1747-5:1972 Methods for the measurement of air pollution. Directional dust gauges
    This standard has been withdrawn as it conflicts with new European standards
  • BS 1881-5:1970 Testing concrete. Methods of testing hardened concrete for other than strength
    Superseded by BS 1881-114:1983, BS 1881-121:1983, BS 1881-122:1983 and BS 1881-208:1996
  • BS 2000-315:1998 (ISO 5662:1997) Methods of test for petroleum and its products. Petroleum products. Electrical insulating oils. Detection of corrosive sulphur
    This standard has been withdrawn as it is identical to ISO 5662:1997 which has been withdrawn by ISO/TC 28
  • BS 2015:1992 Glossary of paint and related terms
    Superseded by BS EN 971-1:1996
  • BS 2472:1966 Methods for the chemical analysis of ice cream
    Superseded by BS 2472-3:1989
  • BS 2782-1:Methods 134A and 134B:1992 Methods of testing plastics. Thermal properties. Determination of the oxidation induction time of thermoplastics
    This standard has been withdrawn in favour of ISO 11357
  • BS 2782-1:Method 151A:1984 Methods of testing plastics. Thermal properties. Determination of cold bend temperature of flexible polyvinyl chloride extrusion compound
    This standard has been withdrawn as it is no longer used
  • BS 2782-2:Method 241A:1984 Methods of testing plastics. Electrical properties. Determination of effect of polyvinyl chloride compound on the loss tangent of polyethylene
    This standard has been withdrawn as it is no longer used
  • BS 2782-3:Methods 320A to 320F:1976 Methods of testing plastics. Mechanical properties. Tensile strength, elongation and elastic modulus
    This standard has been withdrawn in favour of ISO 527
  • BS 2782-3:Method 341A:1977 Methods of testing plastics. Mechanical properties. Determination of apparent interlaminar shear strength of reinforced plastics
    This standard has been withdrawn in favour of ISO 14130
  • BS 2782-9:Method 940A:1990 (ISO 2557-1:1989) Methods of testing plastics. Sampling and test specimen preparation. Preparation of test specimens of amorphous thermoplastics in the form of bars with a specified reversion
    This standard has been withdrawn as it is identical to ISO 2557-1:1989 which has been withdrawn by ISO/TC 61/SC 9/WG 18
  • BS 2898:1970 Specification for wrought aluminium and aluminium alloys for electrical purposes. Bars, extruded round tube and sections
    Superseded by BS EN 755-3:1996, BS EN 755-4:1996, BS EN 755-5:1996 and BS EN 755-6:1996
  • BS 2915:1990 Specification for bursting discs and bursting disc devices
    Superseded by BS EN ISO 4126-2:2003 and BS EN ISO 4126-6:2003
  • BS 3202-2:1991 Laboratory furniture and fittings. Specification for performance
    This standard has been withdrawn as it is partially replaced by BS EN 13150:2001
  • BS 3564:1986 (ISO 67:1981) Method for size-grading of muscovite mica blocks, thins and films
    This standard has been withdrawn as it is identical to ISO 67:1981 which has been withdrawn by ISO/TC 56
  • BS 3676-1:1989 Switches for household and similar fixed electrical installations. Specification for general requirements
    This standard has been withdrawn as it is replaced by BS EN 60669-1:1996. It was originally retained as it covers DC requirements (which are not included in BS EN 60669-1). However, the requirements for DC in BS 3676-1:1989 are minimal to the extent that it is unsafe to allow this standard to continue to claim that it covers DC performance of switches
  • BS 3811:1993 Glossary of terms used in terotechnology
    This standard has been withdrawn as it is outdated and has been superseded by more recent standards in the areas of life-cycle costing as well as the BS EN 60300 suite of dependability standards
  • BS 3682-2:1969 Specification for railway brake hose. Specification for vacuum brake hose
    Superseded by BS 3682-1:1994
  • BS 3748:1992 (ISO 2493:1992) Method for determination of resistance to bending of paper and board
    Superseded by BS ISO 2493-1:2010; and BS ISO 2493-2:2011
  • BS 3843-1:1992 Guide to terotechnology (the economic management of assets). Introduction to terotechnology
    This standard has been withdrawn as it is outdated and has been superseded by more recent standards in the areas of life-cycle costing as well as the BS EN 60300 suite of dependability standards
  • BS 3843-2:1992 Guide to terotechnology (the economic management of assets). Introduction to the techniques and applications
    This standard has been withdrawn as it is outdated and has been superseded by more recent standards in the areas of life-cycle costing as well as the BS EN 60300 suite of dependability standards
  • BS 3843-3:1992 Guide to terotechnology (the economic management of assets). Guide to the available techniques
    This standard has been withdrawn as it is outdated and has been superseded by more recent standards in the areas of life-cycle costing as well as the BS EN 60300 suite of dependability standards
  • BS 3892-2:1996 Pulverized-fuel ash. Specification for pulverized-fuel ash to be used as a Type I addition
    This standard has been withdrawn as it has effectively been taken over by other European Standards for more than 5 years
  • BS 3892-3:1997 Pulverized-fuel ash. Specification for pulverized-fuel ash for use in cementitious grouts
    This standard has been withdrawn as it has been effectively taken over by other European Standards for more than 5 years
  • BS 3900-A17:1986 (ISO 7877:1984) Methods of test for paints. Tests on liquid paints (excluding chemical tests). Coating of test panels at a specified spreading rate
    This standard has been withdrawn as it is identical to ISO 7877:1984 which has been withdrawn by ISO/TC 35/SC 9
  • BS 3900-C9:1982 (ISO 4627:1981) Methods of test for paints. Tests associated with paint film formation. Methods for evaluation of the compatibility of a product with a surface to be painted
    This standard has been withdrawn as it is identical to ISO 4627:1981 which has been withdrawn by ISO/TC 35/SC 9
  • BS 3900-E3:1973 Methods of test for paints. Impact (falling weight) resistance
    Superseded by BS EN ISO 6272:1994
  • BS 3900-E12.1:2000 (ISO 6441-1:1999) Methods of test for paints. Determination of Knoop hardness by measurement of the indentation length using a microscope
    This standard has been withdrawn as it is identical to ISO 6441-1:1999 which has been withdrawn by ISO/TC 35/SC 9
  • BS 3900-E12.2:2000 (ISO 6441-2:1999) Methods of test for paints. Determination of Knoop hardness by measurement of the indentation depth
    This standard has been withdrawn as it is identical to ISO 6441-2:1999 which has been withdrawn by ISO/TC 35/SC 9
  • BS 4035:1966 Specification for linear measuring instruments for use on building and civil engineering constructional works. Steel measuring tapes, steel bands and retractable steel pocket
    This standard has been withdrawn as it is no longer used. The requirements for metric marking and figuring have been replaced by BS 4484-1:1969
  • BS 4054:1966 Methods for measuring and expressing the performance of radio receivers. Receivers for a.m. and f.m. sound broadcast transmissions
    Superseded by BS 4054-1:1980, BS 4054-2:1980, BS 4054-3:1980 and BS 4054-5:1980
  • BS 4072:1999 Copper/chromium/arsenic preparations for wood preservation
    This standard has been withdrawn as it is no longer required. It gives the specification for copper/chromium/arsenic (CCA) wood preservatives for use in the United Kingdom. Approval for such preservatives was withdrawn by HSE in 2006. It would be illegal to advertise, supply or use such preservatives now
  • BS 4415-1:1992 (ISO 1924-1:1992) Determination of the tensile properties of paper and board. Constant rate of loading method
    This standard has been withdrawn as it is identical to ISO 1924-1:1992 which has been withdrawn by ISO/TC 6/SC 2
  • BS 4485-1:1969 Water cooling towers. Glossary of terms
    Superseded by BS 4485-2:1988 and BS 4485-3:1988
  • BS 4496:1984 (ISO 776:1982) Method for determination of acid-insoluble ash of pulp
    Superseded by BS ISO 776:2011
  • BS 4559-9.2:1988 (ISO 6711:1981) Methods for preparation of calibration gas mixtures. Comparison methods and methods for establishing traceability. Checking by a comparison method
    This standard has been withdrawn as it is identical to ISO 6711:1981 which has been withdrawn by ISO/TC 158
  • BS 4656-30:1992 Accuracy of machine tools and methods of test. Specification for machining centres and computer numerically controlled milling machines, horizontal and vertical spindle types
    Superseded by BS ISO 10791-1:1998, BS ISO 10791-3:1998, BS ISO 10791-4:1998, BS ISO 10791-5:1998, BS ISO 10791-6:1998 and BS ISO 10791-7:1998
  • BS 4815:1972 Glossary of generic names for man-made fibres
    Superseded by BS 4815:1990
  • BS 5202-18:1997 (ISO 11454:1997) Methods for chemical analysis of tobacco and tobacco products. Determination of vapour phase nicotine in air (gas-chromatographic method)
    This standard has been withdrawn as it is identical to ISO 11454:1997 which has been withdrawn by ISO/TC 126
  • BS 5266-10:2008 Guide to the design and provision of emergency lighting to reduce the risks from hazards in the event of failure of the normal lighting supply
    Superseded by BS 5266-1:2011
  • BS 5292:1980 Specification for jointing materials and compounds for installations using water, low pressure steam or 1st, 2nd and 3rd family gases
    Superseded by BS 6956-1:1988, BS 6956-5:1992, BS 6956-6:1992 and BS 6956-7:1992
  • BS 5543:1978 Vacuum technology. Graphical symbols
    This standard has been withdrawn as it is identical to ISO 3753:1977 which has been withdrawn by ISO/TC 112
  • BS 5588-1:1990 Fire precautions in the design, construction and use of buildings. Code of practice for residential buildings
    Superseded by BS 9991:2011
  • BS 5700:1984 Guide to process control using quality control chart methods and cusum techniques
    This standard has been withdrawn as it is no longer used
  • BS 5727:1979 (ISO 3891:1978) Method for describing aircraft noise heard on the ground
    This standard has been withdrawn as it is identical to ISO 3891:1978 which has been withdrawn by ISO/TC 43/SC 1
  • BS 5750-8:1991 (EN 29004-2:1993, ISO 9004-2:1991) Quality systems. Guide to quality management and quality systems elements for services
    This standard has been withdrawn as it is identical to ISO 9004-2:1991 which has been withdrawn by ISO/TC 176/SC 2
  • BS 5763-13:1998 Methods for microbiological examination of food and animal feeding stuffs. Enumeration of Escherichia coli. Colony-count technique at 44°C using membranes
    This standard has been withdrawn as it is no longer used. ISO 6391:1997, on which it was based, although not identical, has been withdrawn. BS ISO 16649-1 is a current standard for E. coli using a membrane approach and BS ISO 16649-2 and DD ISO/TS 16649-3 provide alternative methods
  • BS 5804:1979 (ISO 2185:1972) Method of visual classification for muscovite mica blocks, thins and films
    This standard has been withdrawn as it is identical to ISO 2185:1972 which has been withdrawn by ISO/TC 56
  • BS 5805:1979 (ISO 5023:1977) Method of thermal classification for phlogopite mica splittings
    This standard has been withdrawn as it is identical to ISO 5023:1977 which has been withdrawn by ISO/TC 56
  • BS 5806:1979 (ISO 5972:1978) Method of measurement of thickness for mica blocks, thins, films and splittings
    This standard has been withdrawn as it is identical to ISO 5972:1978 which has been withdrawn by ISO/TC 56
  • BS 5886:1980 (ISO 4483:1979) Methods for field pressure testing of asbestos-cement pipelines
    This standard has been withdrawn as it is identical to ISO 4483:1979 which has been withdrawn by ISO/TC 77
  • BS 5927:1980 (ISO 4482:1979) Guide for laying of asbestos-cement pipelines
    This standard has been withdrawn as it is identical to ISO 4482:1979 which has been withdrawn by ISO/TC 77
  • BS 5929-7:1992 (ISO 3972:1991) Methods for sensory analysis of food. Investigating sensitivity of taste
    Superseded by BS ISO 3972:2011
  • BS 5952:1980 (ISO 5816:1979) Specification for muscovite mica components for electronic equipment
    This standard has been withdrawn as it is identical to ISO 5816:1979 which has been withdrawn by ISO/TC 56
  • BS 5978-1:1989 Safety and performance of gas-fired hot water boilers (60 kW to 2 MW input). Specification for general requirements
    Superseded by BS EN 656:2000
  • BS 5978-2:1989 Safety and performance of gas-fired hot water boilers (60 kW to 2 MW input). Specification for additional requirements for boilers with atmospheric burners
    Superseded by BS EN 656:2000
  • BS 5978-3:1989 Safety and performance of gas-fired hot water boilers (60 kW to 2 MW input). Specification for additional requirements for boilers with forced or induced draught burners
    Superseded by BS EN 656:2000
  • BS 6068-2.39:1991 Water quality. Physical, chemical and biochemical methods. Method for the determination of sulphate using barium chloride and gravimetry
    This standard has been withdrawn as it is identical to ISO 9280:1990 which has been withdrawn by ISO/TC 147/SC 2
  • BS 6072:1981 Method for magnetic particle flaw detection
    Superseded by BS EN ISO 9934-1:2001
  • BS 6109-1:1981 Tail lifts, mobile lifts and ramps associated with vehicles. Code of practice for tail lifts
    Superseded by BS EN 1756-1:2001+A1:2008
  • BS 6109-2:1989 Tail lifts, mobile lifts and ramps associated with vehicles. Code of practice for passenger lifts and ramps
    Superseded by BS EN 1756-2:2004+A1:2009
  • BS 6166-1:1986 Lifting slings. Methods of rating
    This standard has been withdrawn as it is no longer used
  • BS 6166-2:1986 Lifting slings. Specification for marking
    This standard has been withdrawn as it is no longer used
  • BS 6225-1:1982 (ISO 3782:1980) Method for determining the resistance to picking of paper and board: accelerating speed method using the IGT tester. Pendulum or spring model
    This standard has been withdrawn as it is identical to ISO 3782:1980 which has been withdrawn by ISO/TC 6/SC 2
  • BS 6237:1982 (ISO 6386:1981) Method for grading and visual classification for muscovite mica splittings
    This standard has been withdrawn as it is identical to ISO 6386:1981 which has been withdrawn by ISO/TC 56
  • BS 6258:1988 Specification for hollow steel bars for machining
    Superseded by BS EN 10294-1:2005
  • BS 6306-2:1982 (ISO 5351-2:1981) Methods for determination of limiting viscosity number of cellulose in dilute solutions. Iron (III) sodium tartrate complex (EWNNmod NaCl) method
    This standard has been withdrawn as it is identical to ISO 5351-2:1981 which has been withdrawn by ISO/TC 6/WG 4
  • BS 6379-3:1983 Sampling of coffee and coffee products. Specification for a coffee trier for sampling green coffee
    Superseded by BS ISO 6666:2011
  • BS 6456:1983 (ISO 6924:1983) Glossary of terms for correspondence envelopes
    This standard has been withdrawn as it is identical to ISO 6924:1983 which has been withdrawn by ISO/TC 6
  • BS 6497:1984 Specification for powder organic coatings for application and stoving to hot-dip galvanized hot-rolled steel sections and preformed steel sheet for windows and associated external architectural purposes, and for the finish on galvanized steel sections and
    Superseded by BS EN 13438:2005
  • BS 6513-4:1984 Wideband cabled distribution systems. Specification for performance requirements, for upstream television
    Superseded by BS 6513-6:1987
  • BS 6544:1984 (ISO 7891:1984) Specification for holes in dozer end bits for earth moving machinery
    This standard has been withdrawn as it is identical to ISO 7891:1984 which has been withdrawn by ISO/TC 127/SC 3
  • BS 6605:1990 Specification for cross recesses for screws
    Superseded by BS EN ISO 4757:1995
  • BS 6785:1986 Code of practice for solar heating systems for swimming pools
    This standard has been withdrawn as it is no longer used
  • BS 6890:1987 (ISO 5634-1986) Method for determination of grease resistance of paper and board
    This standard has been withdrawn as it is identical to ISO 5634:1986 which has been withdrawn by ISO/TC 6/SC 2
  • BS 6911-2:1990 (ISO 8313:1989) Testing earth-moving machinery. Measurement of tool forces and tipping loads of loaders
    This standard has been withdrawn as it is identical to ISO 8313:1989 which has been withdrawn by ISO/TC 127/SC 1
  • BS 6912-2:1989 (ISO 5998:1986) Safety of earth-moving machinery. Specification for rated operating load for crawler and wheel loaders
    This standard has been withdrawn as it is identical to ISO 5998:1986 which has been withdrawn by ISO/TC 127
  • BS 6948:1989 Methods of test for mechanically fastened joints in timber and wood-based materials
    Superseded by BS EN 1380:1999, BS EN 1381:1999, BS EN 1382:1999 and BS EN 1383:1999
  • BS 6955-2:1994 (ISO 5347-2:1993) Calibration of vibration and shock pick-ups. Methods for primary shock calibration by light cutting
    This standard has been withdrawn as it is identical to ISO 5347-2:1993 which has been withdrawn by ISO/TC 108/SC 3/WG 6
  • BS 6955-6:1994 (ISO 5347-6:1993) Calibration of vibration and shock pick-ups. Method for primary vibration calibration at low frequencies
    This standard has been withdrawn as it is identical to ISO 5347-6:1993 which has been withdrawn by ISO/TC 108/SC 3/WG 6
  • BS 6955-9:1994 (ISO 5347-9:1993) Calibration of vibration and shock pick-ups. Method for secondary vibration calibration by comparison of phase angles
    This standard has been withdrawn as it is identical to ISO 5347-9:1993 which has been withdrawn by ISO/TC 108/SC 3/WG 6
  • BS 7012-8:1997 (ISO 9344:1996) Light microscopes. Graticules for eyepieces
    Superseded by BS ISO 9344:2011
  • BS 7111:1991 (ISO 8372:1987) Guide to modes of operation for a 64-bit block cipher algorithm
    This standard has been withdrawn as it is identical to ISO 8372:1987 which has been withdrawn by ISO/IEC/JTC 1/SC 27/WG 2
  • BS 7251-13:1995 (ISO 7206-9:1994) Orthopaedic joint prostheses. Method for determination of resistance to torque of head fixation of stemmed femoral components
    This standard has been withdrawn as it is identical to ISO 7206-9:1994 which has been withdrawn by ISO/TC 150/SC 4/WG 1
  • BS 7252-10:1997 (ISO 5832-10:1996) Metallic materials for surgical implants. Specification for wrought titanium 5-aluminium 2,5-iron alloy
    This standard has been withdrawn as it is identical to ISO 5832-10:1996 which has been withdrawn by ISO/TC 150/SC 1
  • BS 7371-11:1993 Coatings on metal fasteners. Specification for zinc flake non-electrolytically applied cured coatings
    Superseded by BS EN ISO 10683:2000
  • BS 7433-1:1991 Cross recessed machine screws. Specification for pan head screws of product grade A
    Superseded by BS EN ISO 7045:1995
  • BS 7433-2:1991 Cross recessed machine screws. Specification for countersunk flat head screws product grade A and property class 4.8 only
    Superseded by BS EN ISO 7046-1:1994
  • BS 7433-3:1991 Cross recessed machine screws. Specification for raised countersunk head screws product grade A
    Superseded by BS EN ISO 7047:1995
  • BS 7496-1:1991 Cross-recessed tapping screws. Specification for pan head screws
    Superseded by BS EN ISO 7049:1995
  • BS 7496-2:1991 Cross-recessed tapping screws. Specification for countersunk flat head screws
    Superseded by BS EN ISO 7050:1995
  • BS 7496-3:1991 Cross-recessed tapping screws. Specification for raised countersunk head screws
    Superseded by BS EN ISO 7051:1995
  • BS 7572:1992 Code of practice for thermally insulated underground piping systems
    Superseded by BS EN 13941:2003
  • BS 7655-2.4:2000 Specification for insulating and sheathing materials for cables. Cross-linked elastomeric sheathing compounds. Welding cable covering
    Superseded by BS EN 50363-2-2:2005
  • BS 7697:1993 Nominal voltages for low voltage public electricity supply systems
    Superseded by BS EN 60038:2011
  • BS 7843-2.1:1996 Guide to the acquisition and management of meteorological precipitation data. Field practices and data management. Technical aspects in the field
    Superseded by BS 7843-1:2012 and BS 7843-2:2012
  • BS 7843-2.2:1996 Guide to the acquisition and management of meteorological precipitation data. Field practices and data management. Methods of observation and data tabulation
    Superseded by BS 7843-2:2012
  • BS 7843-2.3:1996 Guide to the acquisition and management of meteorological precipitation data. Field practices and data management. Data management
    Superseded by BS 7843-2:2012
  • BS 7850-2:1994 (ISO 9004-4:1993) Total quality management. Guidelines for quality improvement
    This standard has been withdrawn as it is identical to ISO 9004-4:1993 which has been withdrawn by ISO/TC 176/SC 2
  • BS 9450:1975 Specification for integrated electronic circuits and micro-assemblies of assessed quality (capability approval procedures): generic data and methods of test
    Superseded by BS 9450:1998
  • DD 220:1994 (ISO/TR 11046:1994) Soil quality. Determination of mineral oil content. Method by infrared spectrometry and gas chromatographic method
    This standard has been withdrawn as it is identical to ISO/TR 11046:1994 which has been withdrawn by ISO/TC 190/SC 3/WG 6
  • DD CEN/TS 15958:2009 Fertilizers. Extraction of water soluble phosphorus
    Superseded by BS EN 15958:2011
  • DD CEN/TS 15959:2009 Fertilizers. Determination of extracted phosphorus
    Superseded by BS EN 15959:2011
  • DD CEN/TS 15960:2009 Fertilizers. Extraction of total calcium, total magnesium, total sodium and total sulfur in the forms of sulfates
    Superseded by BS EN 15960:2011
  • DD CEN/TS 15961:2009 Fertilizers. Extraction of water-soluble calcium, magnesium, sodium and sulfur (in the forms of sulfates)
    Superseded by BS EN 15961:2011
  • DD CEN/TS 16032:2010 Fertilizers. Extraction and determination of elemental sulphur
    Superseded by BS EN 16032:2011
  • BS EN 792-9:2001+A1:2008 Hand-held non-electric power tools. Safety requirements. Die grinders
    Superseded by BS EN ISO 11148-9:2011
  • BS EN ISO 1133:2005 Plastics. Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics
    Superseded by BS EN ISO 1133-2:2011
  • BS EN 1501-1:1998+A2:2009 Refuse collection vehicles and their associated lifting devices. General requirements and safety requirements. Rear-end loaded refuse collection vehicles
    Superseded by BS EN 1501-1:2011 and BS EN 1501-5:2011
  • BS EN 1612-2:2000+A1:2008 Plastics and rubber machines. Reaction moulding machines. Safety requirements for reaction moulding plant
    This standard has been withdrawn following the identical European Standard also being withdrawn without replacement
  • BS EN ISO 7783-1:2000 (BS 3900-G9:1996) Paints and varnishes. Coating materials and coating systems for exterior masonry and concrete. Determination of water-vapour transmission rate of free films (dish method)
    Superseded by BS EN ISO 7783:2011
  • BS EN ISO 7783-2:1999 Paints and varnishes. Coating materials and coating systems for exterior masonry and concrete. Determination and classification of water-vapour transmission rate (permeability)
    Superseded by BS EN ISO 7783:2011
  • BS EN ISO 8580:1995 Rubber and plastics hoses. Determination of ultra-violet resistance under static conditions
    Superseded by BS EN ISO 30013:2011
  • BS EN ISO 11758:1997 Rubber and plastics hoses. Exposure to a xenon arc lamp. Determination of changes in colour and appearance
    Superseded by BS EN ISO 30013:2011
  • BS EN ISO 11990:2003 Optics and optical instruments. Lasers and laserrelated equipment. Determination of laser resistance of tracheal tube shafts
    Superseded by BS EN ISO 11990-1:2011
  • BS EN ISO 12137-1:2006 (BS 3900-E17:1997) Paints and varnishes. Determination of mar resistance. Method using a curved stylus
    Superseded by BS EN ISO 12137:2011
  • BS EN ISO 12137-2:2006 (BS 3900-E18:1997) Paints and varnishes. Determination of mar resistance. Method using a pointed stylus
    Superseded by BS EN ISO 1518-2:2011
  • DD CEN/TS 13126-3:2004 Building hardware, fittings for windows and door height windows. Requirements and test methods. Manoeuvring fittings for espagnolette bolts/sliding button
    Superseded by BS EN 13126-3:2011
  • DD CEN/TS 13126-5:2004 Building hardware, fittings for windows and door height windows. Requirements and test methods. Devices that restrict the opening of windows
    Superseded by BS EN 13126-5:2011
  • BS EN 13244-1:2002 Plastics piping systems for buried and aboveground pressure systems for water for general purposes, drainage and sewerage. Polyethylene (PE). General
    Superseded by BS EN 12201-1:2011
  • BS EN 13244-2:2002 Plastics piping systems for buried and aboveground pressure systems for water for general purposes, drainage and sewerage. Polyethylene (PE). Pipes
    Superseded by BS EN 12201-2:2011
  • BS EN 13244-3:2002 Plastics piping systems for buried and aboveground pressure systems for water for general purposes, drainage and sewerage. Polyethylene (PE). Fittings
    Superseded by BS EN 12201-3:2011
  • BS EN 13244-5:2002 Plastics piping systems for buried and aboveground pressure systems for water for general purposes, drainage and sewerage. Polyethylene (PE). Fitness for purpose of the system
    Superseded by BS EN 12201-5:2011
  • BS EN 14189:2003 Transportable gas cylinders. Inspection and maintenance of cylinder valves at time of periodic inspection of gas cylinders
    Superseded by BS EN ISO 22434:2011
  • BS EN 14861:2004+A1:2009 Forest machinery. Self propelled machinery. Safety requirements
    Superseded by BS EN ISO 11850:2011
  • DD CEN/TS 15022-4:2006 Copper and copper alloys. Determination of tin content. Medium tin content. Flame atomic absorption spectrometry method (FAAS)
    Superseded by BS EN 15022-4:2011
  • DD CEN/TS 15150:2005 Solid biofuels. Methods for the determination of particle density
    Superseded by BS EN 15150:2011
  • DD CEN/TS 15359:2006 Solid recovered fuels. Specifications and classes
    Superseded by BS EN 15359:2011
  • BS EN ISO 19011:2002 (A5 Laminated) Guidelines for quality and/or environmental management systems auditing. A5 laminated edition
    This product has been withdrawn as a 2011 edition of the BS has just been published
  • BS EN 23035:1994 (ISO 3035:1982) Single-faced and single-wall corrugated fibreboard. Determination of flat crush resistance
    Superseded by BS EN ISO 3035:2011
  • BS ISO 248:2005 Rubber, raw. Determination of volatile-matter content
    Superseded by BS ISO 248-1:2011
  • BS ISO 406:1987 Technical drawings. Tolerancing of linear and angular dimensions
    Superseded by BS EN ISO 14405-2:2011
  • BS ISO 777:2005 Paper, board and pulp. Determination of acid soluble calcium
    Superseded by BS ISO 12830:2011
  • BS ISO 778:2005 Paper, board and pulp. Determination of acid soluble copper
    Superseded by BS ISO 12830:2011
  • BS ISO 779:2005 Paper, board and pulp. Determination of acid soluble iron
    Superseded by BS ISO 12830:2011
  • BS ISO 1830:2005 Paper, board and pulps. Determination of acid soluble manganese
    Superseded by BS ISO 12830:2011
  • BS ISO 1834:1999 Short link chain for lifting purposes. General conditions of acceptance
    This standard has been withdrawn as it conflicts with BS EN 818-1:1996+A1:2008
  • BS ISO 2382-22:1986 Information processing systems. Vocabulary. Calculators
    This standard has been withdrawn as it is identical to ISO 2382-22:1986 which has been withdrawn by ISO/IEC/JTC 1
  • BS ISO 3272-5:1999 Microfilming of technical drawings and other drawing office documents. Test procedures for diazo duplicating of microfilm images in aperture cards
    This standard has been withdrawn as it is identical to ISO 3272-5:1999 which has been withdrawn by ISO/TC 171/SC 2
  • BS ISO 3322:1985 Fluid power systems and components. Cylinders. Nominal pressures
    This standard has been withdrawn as it is identical to ISO 3322:1985 which has been withdrawn by ISO/TC 131/SC 3/WG 1
  • BS ISO 3384:2005 Rubber, vulcanized or thermoplastic. Determination of stress relaxation in compression at ambient and at elevated temperatures
    Superseded by BS ISO 3384-1:2011
  • BS ISO 7180:1986 Pneumatic fluid power. Cylinders. Bore and port thread sizes
    This standard has been withdrawn as it is identical to ISO 7180:1986 which has been withdrawn by ISO/TC 131/SC 3
  • BS ISO 7341:2005 Banking. Nostro accounts reconciliation
    This standard has been withdrawn as it is identical to ISO 7341:2005 which has been withdrawn by ISO/TC 68/SC 7
  • BS ISO 7772-1:1998 Assessment of industrial laundry machinery by its effect on textiles. Washing machines
    This standard has been withdrawn as it is identical to ISO 7772-1:1998 which has been withdrawn by ISO/TC 38
  • BS ISO 7772-2:1996 Assessment of industrial laundry machinery by its effect on textiles. Extracting machines
    This standard has been withdrawn as it is identical to ISO 7772-2:1996 which has been withdrawn by ISO/TC 38
  • BS ISO 7772-3:1996 Assessment of industrial laundry machinery by its effect on textiles. Flatwork-ironing machines
    This standard has been withdrawn as it is identical to ISO 7772-3:1996 which has been withdrawn by ISO/TC 38
  • BS ISO 7772-4:1996 Assessment of industrial laundry machinery by its effect on textiles. Batch-drying tumblers
    This standard has been withdrawn as it is identical to ISO 7772-4:1996 which has been withdrawn by ISO/TC 38
  • BS ISO 8127-2:1999 Micrographics. A6 size microfilm jackets. Other types of jacket for 16 mm and 35 mm microfilm
    This standard has been withdrawn as it is identical to ISO 8127-2:1999 which has been withdrawn by ISO/TC 171/SC 2/WG 1
  • BS ISO 9000-2:1997 Quality management and quality assurance standards. Generic guidelines for the application of ISO 9001, ISO 9002 and ISO 9003
    This standard has been withdrawn as it is identical to ISO 9000-2:1997 which has been withdrawn by ISO/TC 176/SC 2
  • BS ISO 9056:1990 Glass containers. Series of pilferproof finish. Dimensions
    This standard has been withdrawn as it is identical to ISO 9056:1990 which has been withdrawn by ISO/TC 63
  • BS ISO TR 9122-2:1990 Toxicity testing of fire effluents. Guidelines for biological assays to determine the acute inhalation toxicity of fire effluents (basic principles, criteria and methodology
    This standard has been withdrawn as it is identical to ISO/TR 9122-2:1990 which has been withdrawn by ISO/TC 92/SC 3
  • BS ISO TR 9122-5:1993 Toxicity testing of fire effluents. Prediction of toxic effects of fire effluents
    This standard has been withdrawn as it is identical to ISO/TR 9122-5:1993 which has been withdrawn by ISO/TC 92/SC 3/WG 5
  • BS ISO 9336-2:1994 Optics and optical instruments. Application. Optical transfer function. Lenses for office copiers
    This standard has been withdrawn as it is identical to ISO 9336-2:1994 which has been withdrawn by ISO/TC 172/SC 1/WG 1
  • BS ISO/TR 9494:1997 (ISO/TR 9494:1997) Petroleum liquids. Automatic pipeline sampling. Statistical assessment of performance of automatic samplers determining the water content in hydrocarbon liquids
    This standard has been withdrawn as it is identical to ISO/TR 9494:1997 which has been withdrawn by ISO/TC 28/SC 2
  • BS ISO/IEC 9979:1999 Information technology. Security techniques. Procedures for the registration of cryptographic algorithms
    This standard has been withdrawn as it is identical to ISO/IEC 9979:1999 which has been withdrawn by ISO/IEC/JTC 1/SC 27/WG 1
  • BS ISO/IEC 10025-3:1993 Information technology. Telecommunications and information exchange between systems. Transport conformance testing for connection-mode transport protocol operating over connection-mode network service. Transport test management protocol specification
    This standard has been withdrawn as it is identical to ISO/IEC 10025-3:1993 which has been withdrawn by ISO/IEC/JTC 1/SC 6/WG 7
  • BS ISO 10110-13:1997 Optics and optical instruments. Preparation of drawings for optical elements and systems. Laser irradiation damage threshold
    This standard has been withdrawn as it is identical to ISO 10110-13:1997 which has been withdrawn by ISO/TC 172/SC 1/WG 2
  • BS ISO/IEC 10168-1:1997 Information technology. Open systems interconnection. Conformance test suite for the session protocol. Test suite structure and test purposes
    This standard has been withdrawn as it is identical to ISO/IEC 10168-1:1997 which has been withdrawn by ISO/IEC/JTC 1
  • BS ISO/IEC 10168-4:1996 Information technology. Open systems interconnection. Conformance test suite for the session protocol. Test management protocol specification
    This standard has been withdrawn as it is identical to ISO/IEC 10168-4:1996 which has been withdrawn by ISO/IEC/JTC 1
  • BS ISO/IEC 10169-1:1991 Information technology. Open systems interconnection. Conformance test suite for the ACSE protocol. Test suite structure and test purposes
    This standard has been withdrawn as it is identical to ISO/IEC 10169-1:1991 which has been withdrawn by ISO/IEC/JTC 1
  • BS ISO/IEC 10170-1:1993 Information technology. Open systems interconnection. Conformance test suite for the FTAM protocol. Test suite structure and test purposes
    This standard has been withdrawn as it is identical to ISO/IEC 10170-1:1993 which has been withdrawn by ISO/IEC/JTC 1
  • PD ISO/TR 10200:1990 Legal admissibility of microforms
    This standard has been withdrawn as it is identical to ISO/TR 10200:1990 which has been withdrawn by ISO/TC 171/SC 3
  • BS ISO 10202-2:1996 Financial transaction cards. Security architecture of financial transaction systems using integrated circuit cards. Transaction process
    This standard has been withdrawn as it is identical to ISO 10202-2:1996 which has been withdrawn by ISO/TC 68/SC 2
  • BS ISO/IEC ISP 10608-5:1992 Information technology. International standardized profile TAnnnn. Connection-mode transport service over connectionless-mode network service. TA1111/TA1121 profiles including subnetwork-dependent requirements for X.25 packet-switched data networks using
    This standard has been withdrawn as it is identical to ISO/IEC ISP 10608-5:1992 which has been withdrawn by ISO/IEC/JTC 1
  • BS ISO/IEC ISP 10608-14:1995 Information technology. International standardized profile TAnnnn. Connection-mode transport service over connectionless-mode network service. MAC, PHY and PMD sublayer dependent and Station Management requirements over an FDDI LAN subnetwork
    This standard has been withdrawn as it is identical to ISO/IEC ISP 10608-14:1995 which has been withdrawn by ISO/IEC/JTC 1
  • BS ISO/IEC ISP 10609-1:1992 Information technology. International standardized profiles TB, TC, TD and TE. Connection-mode transport service over connection-mode network service. Subnetworktype independent requirements for Group TB
    This standard has been withdrawn as it is identical to ISO/IEC ISP 10609-1:1992 which has been withdrawn by ISO/IEC/JTC 1
  • BS ISO/IEC ISP 10609-5:1992 Information technology. International standardized profiles TB, TC, TD and TE. Connection-mode transport service over connection-mode network service. Definition of profiles TB1111/TB1121
    This standard has been withdrawn as it is identical to ISO/IEC ISP 10609-5:1992 which has been withdrawn by ISO/IEC/JTC 1
  • BS ISO/IEC ISP 10615-4:1996 Information technology. International standardized profiles ADInn. OSI directory. ADI22. DSA invoker role
    This standard has been withdrawn as it is identical to ISO/IEC ISP 10615-4:1996 which has been withdrawn by ISO/IEC/JTC 1
  • BS ISO/IEC ISP 10616:1995 Information technology. International standardized profile FDI11. Directory data definitions. Common directory use (Normal)
    This standard has been withdrawn as it is identical to ISO/IEC ISP 10616:1995 which has been withdrawn by ISO/IEC/JTC 1
  • BS ISO/IEC 10729-1:1993 Information technology. Open Systems Interconnection. Conformance test suite for the presentation layer. Test suite structure and test purposes for the presentation protocol
    This standard has been withdrawn as it is identical to ISO/IEC 10729-1:1993 which has been withdrawn by ISO/IEC/JTC 1
  • BS ISO/IEC 10729-2:1995 Information technology. Open Systems Interconnection. Conformance test suite for the presentation layer. Test suite structure and test purposes for the ASN.1 basic encodings
    This standard has been withdrawn as it is identical to ISO/IEC 10729-2:1995 which has been withdrawn by ISO/IEC/JTC 1
  • BS ISO/IEC 10739-1:1994 Information technology. Open Systems Interconnection. Test suite structure and test purposes
    This standard has been withdrawn as it is identical to ISO/IEC 10739-1:1994 which has been withdrawn by ISO/IEC/JTC 1
  • BS ISO 10756:1994 Graphic technology. Prepress digital data exchange. Colour line art data on magnetic tape
    This standard has been withdrawn as it is identical to ISO 10756:1994 which has been withdrawn by ISO/TC 130/WG 2
  • BS ISO 10758:1994 Graphic technology. Prepress digital data exchange. Online transfer from electronic prepress systems to colour hardcopy devices
    This standard has been withdrawn as it is identical to ISO 10758:1994 which has been withdrawn by ISO/TC 130/WG 2
  • BS ISO 10759:1994 Graphic technology. Prepress digital data exchange. Monochrome image data on magnetic tape
    This standard has been withdrawn as it is identical to ISO 10759:1994 which has been withdrawn by ISO/TC 130/WG 2
  • BS ISO/IEC 10857:1994 Information technology. Microprocessor systems. Futurebus+. Logical protocol specification
    This standard has been withdrawn as it is identical to ISO/IEC 10857:1994 which has been withdrawn by ISO/IEC/JTC 1
  • BS ISO/IEC ISP 11184-1:1995 Information technology. International Standardized Profiles FVT1nn. Virtual Terminal Basic Class. Register of VTE- profiles. FVT121, FVT122. S-mode forms and paged VTE-profiles
    This standard has been withdrawn as it is identical to ISO/IEC ISP 11184-1:1995 which has been withdrawn by ISO/IEC/JTC 1
  • BS ISO/IEC ISP 11184-2:1996 Information technology. International Standardized Profiles FVT1nn. Virtual Terminal Basic Class. Register of VTE- profiles. FVT115. Amode Generalized Telnet VTE-profile
    This standard has been withdrawn as it is identical to ISO/IEC ISP 11184-2:1996 which has been withdrawn by ISO/IEC/JTC 1
  • BS ISO/IEC ISP 11184-3:1996 Information technology. International Standardized Profiles FVT1nn. Virtual Terminal Basic Class. Register of VTE- profiles. FVT114. Amode transparent VTE-profile
    This standard has been withdrawn as it is identical to ISO/IEC ISP 11184-3:1996 which has been withdrawn by ISO/IEC/JTC 1
  • BS ISO/IEC ISP 11185-12:1995 Information technology. International standardized profiles FVT2nn. Virtual terminal basic class. Register of control object type definitions. FVT2116. Generalized Telnet Synch Control Object; FVT2117. Generalized Telnet Signal Control Object; FVT2118. Ge
    This standard has been withdrawn as it is identical to ISO/IEC ISP 11185-12:1995 which has been withdrawn by ISO/IEC/JTC 1
  • BS ISO/IEC ISP 11185-13:1995 Information technology. International standardized profiles FVT2nn. Virtual terminal basic class. Register of control object type definitions. FVT2111. Waiting time control object
    This standard has been withdrawn as it is identical to ISO/IEC ISP 11185-13:1995 which has been withdrawn by ISO/IEC/JTC 1
  • BS ISO/IEC ISP 11185-14:1995 Information technology. International standardized profiles FVT2nn. Virtual terminal basic class. Register of control object type definitions. FVT2112. Printer control object
    This standard has been withdrawn as it is identical to ISO/IEC ISP 11185-14:1995 which has been withdrawn by ISO/IEC/JTC 1
  • BS ISO/IEC ISP 11185-15:1995 Information technology. International standardized profiles FVT2nn. Virtual terminal basic class. Register of control object type definitions. FVT2113. Field definition management control object
    This standard has been withdrawn as it is identical to ISO/IEC ISP 11185-15:1995 which has been withdrawn by ISO/IEC/JTC 1
  • BS ISO/IEC ISP 11185-16:1995 Information technology. International standardized profiles FVT2nn. Virtual terminal basic class. Register of control object type definitions. FVT2114. Terminal signal titles control object
    This standard has been withdrawn as it is identical to ISO/IEC ISP 11185-16:1995 which has been withdrawn by ISO/IEC/JTC 1
  • BS ISO/IEC ISP 11185-17:1995 Information technology. International standardized profiles FVT2nn. Virtual terminal basic class. Register of control object type definitions. FVT2115. Help text control object
    This standard has been withdrawn as it is identical to ISO/IEC ISP 11185-17:1995 which has been withdrawn by ISO/IEC/JTC 1
  • BS ISO/IEC 11186-2:1996 Information technology. International standardized profiles FVT3nn. Virtual terminal basic class. Register of attribute assignment type definitions. FVT311. Repertoire Assignment Type for ISO/IEC 10646
    This standard has been withdrawn as it is identical to ISO/IEC ISP 11186-2:1996 which has been withdrawn by ISO/IEC/JTC 1
  • BS ISO/IEC ISP 11186-4:1997 Information technology. International standardized profiles FVT3nn. Virtual terminal basic class. Register of attribute assignment type definitions. FVT322. Font Assignment Type No. 2
    This standard has been withdrawn as it is identical to ISO/IEC ISP 11186-4:1997 which has been withdrawn by ISO/IEC/JTC 1
  • BS ISO/IEC ISP 11188-2:1996 Information technology. International standardized profiles. Common upper layer requirements. Basic connection oriented requirements for ROSE-based profiles
    This standard has been withdrawn as it is identical to ISO/IEC ISP 11188-2:1996 which has been withdrawn by ISO/IEC/JTC 1
  • BS ISO/IEC 11588-3:1997 Information technology. Message handling systems (MHS) management. Logging information
    This standard has been withdrawn as it is identical to ISO/IEC 11588-3:1997 which has been withdrawn by ISO/IEC/JTC 1/SC 6
  • BS ISO/IEC 11588-8:1997 Information technology. Message handling systems (MHS) management. Message transfer agent management
    This standard has been withdrawn as it is identical to ISO/IEC 11588-8:1997 which has been withdrawn by ISO/IEC/JTC 1/SC 6
  • BS ISO/IEC TR 11589:1995 Information technology. Open systems interconnection. LOTOS description of the CCR service
    This standard has been withdrawn as it is identical to ISO/IEC TR 11589:1995 which has been withdrawn by ISO/IEC/JTC 1
  • BS ISO/IEC TR 11590:1995 Information technology. Open systems interconnection. LOTOS description of the CCR protocol
    This standard has been withdrawn as it is identical to ISO/IEC TR 11590:1995 which has been withdrawn by ISO/IEC/JTC 1
  • BS ISO 11605:1995 Paper and board. Calibration of variable-area flowmeters
    This standard has been withdrawn as it is identical to ISO 11605:1995 which has been withdrawn by ISO/TC 6/SC 2
  • BS ISO/IEC ISP 12059-0:1995 Information technology. International standardized profiles. OSI management. Common information for management functions. Common definitions for management function profiles
    This standard has been withdrawn as it is identical to ISO/IEC ISP 12059-0:1995 which has been withdrawn by ISO/IEC/JTC 1
  • BS ISO/IEC ISP 12059-1:1995 Information technology. International standardized profiles. OSI management. Common information for management functions. Object management
    This standard has been withdrawn as it is identical to ISO/IEC ISP 12059-1:1995 which has been withdrawn by ISO/IEC/JTC 1
  • BS ISO/IEC ISP 12059-2:1995 Information technology. International standardized profiles. OSI management. Common information for management functions. State management
    This standard has been withdrawn as it is identical to ISO/IEC ISP 12059-2:1995 which has been withdrawn by ISO/IEC/JTC 1
  • BS ISO/IEC ISP 12059-3:1995 Information technology. International standardized profiles. OSI management. Common information for management functions. Attributes for representing relationships
    This standard has been withdrawn as it is identical to ISO/IEC ISP 12059-3:1995 which has been withdrawn by ISO/IEC/JTC 1
  • BS ISO/IEC ISP 12059-4:1995 Information technology. International standardized profiles. OSI management. Common information for management functions. Alarm reporting
    This standard has been withdrawn as it is identical to ISO/IEC ISP 12059-4:1995 which has been withdrawn by ISO/IEC/JTC 1
  • BS ISO/IEC ISP 12059-5:1995 Information technology. International standardized profiles. OSI management. Common information for management functions. Event report management
    This standard has been withdrawn as it is identical to ISO/IEC ISP 12059-5:1995 which has been withdrawn by ISO/IEC/JTC 1
  • BS ISO/IEC ISP 12059-6:1995 Information technology. International standardized profiles. OSI management. Common information for management functions. Log control
    This standard has been withdrawn as it is identical to ISO/IEC ISP 12059-6:1995 which has been withdrawn by ISO/IEC/JTC 1
  • BS ISO/IEC ISP 12060-8:1996 Information technology. International standardized profiles. OSI management. Management functions. AOM253x. Summarization objects (including profiles AOM2531-AOM2539)
    This standard has been withdrawn as it is identical to ISO/IEC ISP 12060-8:1996 which has been withdrawn by ISO/IEC/JTC 1
  • BS ISO 12142:2001 Electronic imaging. Media error monitoring and reporting techniques for verification of stored data on optical digital data disks
    This standard has been withdrawn as it is identical to ISO 12142:2001 which has been withdrawn by ISO/TC 171/SC 1
  • BS ISO 12171:2002 Space data and information transfer systems. Telecommand. Channel service
    This standard has been withdrawn as it is identical to ISO 12171:2002 which has been withdrawn by ISO/TC 20/SC 13
  • BS ISO 12172:2003 Space data and information transfer systems. Telecommand. Data routing service
    This standard has been withdrawn as it is identical to ISO 12172:2003 which has been withdrawn by ISO/TC 20/SC 13
  • BS ISO 12173:2003 Space data and information transfer systems. Telecommand. Command operation procedures
    This standard has been withdrawn as it is identical to ISO 12173:2003 which has been withdrawn by ISO/TC 20/SC 13
  • BS ISO 12174:2003 Space data and information transfer systems. Telecommand. Architectural specification for the data management service
    This standard has been withdrawn as it is identical to ISO 12174:2003 which has been withdrawn by ISO/TC 20/SC 13
  • BS ISO 12643-2:2007 Graphic technology. Safety requirements for graphic technology equipment and systems. Press equipment and systems
    Superseded by BS ISO 12643-2:2010
  • BS ISO 12643-3:2008 Graphic technology. Safety requirements for graphic technology equipment and systems. Binding and finishing equipment and systems
    Superseded by BS ISO 12643-3:2010
  • BS ISO 13419:2003 Space data and information transfer systems. Packet telemetry
    This standard has been withdrawn as it is identical to ISO 13419:2003 which has been withdrawn by ISO/TC 20/SC 13
  • BS ISO 13562-1:2000 Industrial variable-reach trucks. Stability tests
    Superseded by BS ISO 22915-11:2011
  • BS ISO/IEC 13650-2:1997 Information technology. Open systems interconnection. Conformance test suite for the OSI TP protocol. Test management protocol specification
    This standard has been withdrawn as it is identical to ISO/IEC 13650-2:1997 which has been withdrawn by ISO/IEC/JTC 1
  • BS ISO 13656:2000 Graphic technology. Application of reflection densitometry and colorimetry to process control or evaluation of prints and proofs
    This standard has been withdrawn as it is identical to ISO 13656:2000 which has been withdrawn by ISO/TC 130/WG 3
  • BS ISO/IEC 13813:1998 Information technology. Programming languages. Generic packages of real and complex type declarations and basic operations for Ada (including vector and matrix types)
    This standard has been withdrawn as it is identical to ISO/IEC 13813:1998 which has been withdrawn by ISO/IEC/JTC 1/SC 22/WG 9
  • BS ISO/IEC 13814:1998 Information technology. Programming languages. Generic package of complex elementary functions for Ada
    This standard has been withdrawn as it is identical to ISO/IEC 13814:1998 which has been withdrawn by ISO/IEC/JTC 1/SC 22/WG 9
  • BS ISO TR 13928:1994 Application guide for ISO 10755, ISO 10756, ISO 10757, ISO 10758 and ISO 10759
    This standard has been withdrawn as it is identical to ISO/TR 13928:1994 which has been withdrawn by ISO/TC 130/WG 2
  • PD ISO/TR 14061:1998 (ISO/TR 14061:1998) Information to assist forestry organizations in the use of environmental management system standards ISO 14001 and ISO 14004
    This standard has been withdrawn as it is identical to ISO/TR 14061:1998 which has been withdrawn by ISO/TC 207
  • BS ISO/IEC TR 14252:1996 Information technology. Guide to the POSIX open system environment (OSE)
    This standard has been withdrawn as it is identical to ISO/IEC TR 14252:1996 which has been withdrawn by ISO/IEC/JTC 1/SC 22/WG 15
  • BS ISO/IEC 14515-2:2003 Information technology. Portable operating system interface (POSIX). Test methods for measuring conformance to POSIX. Shell and utilities
    This standard has been withdrawn as it is identical to ISO/IEC 14515-2:2003 which has been withdrawn by ISO/IEC/JTC 1/SC 22/WG 15
  • BS ISO 14520-3:2000 Gaseous fire-extinguishing systems. Physical properties and system design. FC-2-1-8 extinguishant
    This standard has been withdrawn as it is identical to ISO 14520-3:2000 which has been withdrawn by ISO/TC 21/SC 8
  • BS ISO 14520-4:2000 Gaseous fire-extinguishing systems. Physical properties and system design. FC-3-1-10 extinguishant
    This standard has been withdrawn as it is identical to ISO 14520-4:2000 which has been withdrawn by ISO/TC 21/SC 8
  • BS ISO 14520-7:2000 Gaseous fire-extinguishing systems. Physical properties and system design. HCFC Blend 124 extinguishant
    This standard has been withdrawn as it is identical to ISO 14520-7:2000 which has been withdrawn by ISO/TC 21/SC 8
  • BS ISO 14740:1998 Forestry machinery. Backpack power units for brush cutters, grass trimmers, pole cutters and similar appliances. Safety requirements and testing
    Superseded by BS EN ISO 11680-2:2011
  • BS ISO 14951-1:1999 Space systems. Fluid characteristics. Oxygen
    This standard has been withdrawn as it is identical to ISO 14951-1:1999 which has been withdrawn by ISO/TC 20/SC 14/WG 3
  • BS ISO 14951-2:1999 Space systems. Fluid characteristics. Hydrogen propellant
    This standard has been withdrawn as it is identical to ISO 14951-2:1999 which has been withdrawn by ISO/TC 20/SC 14/WG 3
  • BS ISO 14951-3:1999 Space systems. Fluid characteristics. Nitrogen
    This standard has been withdrawn as it is identical to ISO 14951-3:1999 which has been withdrawn by ISO/TC 20/SC 14/WG 3
  • BS ISO 14951-4:1999 Space systems. Fluid characteristics. Helium
    This standard has been withdrawn as it is identical to ISO 14951-4:1999 which has been withdrawn by ISO/TC 20/SC 14/WG 3
  • BS ISO 14951-5:1999 Space systems. Fluid characteristics. Nitrogen tetroxide propellant
    This standard has been withdrawn as it is identical to ISO 14951-5:1999 which has been withdrawn by ISO/TC 20/SC 14/WG 3
  • BS ISO 14951-6:1999 Space systems. Fluid characteristics. Monomethylhydrazine propellant
    This standard has been withdrawn as it is identical to ISO 14951-6:1999 which has been withdrawn by ISO/TC 20/SC 14/WG 3
  • BS ISO 14951-7:1999 Space systems. Fluid characteristics. Hydrazine propellant
    This standard has been withdrawn as it is identical to ISO 14951-7:1999 which has been withdrawn by ISO/TC 20/SC 14/WG 3
  • BS ISO 14951-8:1999 Space systems. Fluid characteristics. Kerosene propellant
    This standard has been withdrawn as it is identical to ISO 14951-8:1999 which has been withdrawn by ISO/TC 20/SC 14/WG 3'
  • BS ISO 14951-9:1999 Space systems. Fluid characteristics. Argon
    This standard has been withdrawn as it is identical to ISO 14951-9:1999 which has been withdrawn by ISO/TC 20/SC 14/WG 3
  • BS ISO 14951-10:1999 Space systems. Fluid characteristics. Water
    This standard has been withdrawn as it is identical to ISO 14951-10:1999 which has been withdrawn by ISO/TC 20/SC 14/WG 3
  • BS ISO 14951-11:1999 Space systems. Fluid characteristics. Ammonia
    This standard has been withdrawn as it is identical to ISO 14951-11:1999 which has been withdrawn by ISO/TC 20/SC 14/WG 3
  • BS ISO 14951-12:1999 Space systems. Fluid characteristics. Carbon dioxide
    This standard has been withdrawn as it is identical to ISO 14951-12:1999 which has been withdrawn by ISO/TC 20/SC 14/WG 3
  • BS ISO 14951-13:1999 Space systems. Fluid characteristics. Breathing air
    This standard has been withdrawn as it is identical to ISO 14951-13:1999 which has been withdrawn by ISO/TC 20/SC 14/WG 3
  • BS ISO 14985:1999 Hard-copy output of engineering drawings. Specification for the structure of control files
    This standard has been withdrawn as it is identical to ISO 14985:1999 which has been withdrawn by ISO/TC 171/SC 2
  • BS ISO/IEC 15068-2:1999 Information technology. Portable operating system interface (POSIX) system administration. Software administration
    This standard has been withdrawn as it is identical to ISO/IEC 15068-2:1999 which has been withdrawn by ISO/IEC/JTC 1/SC 22/WG 15
  • BS ISO 15078:1998 Machinery for forestry. Log loaders. Location and method of operation of two-lever operator controls
    This standard has been withdrawn as it is identical to ISO 15078:1998 which has been withdrawn by ISO/TC 23/SC 15
  • BS ISO/IEC ISP 15122-2:1999 Information technology. International standardized profiles AOM3nn. OSI management. AOM312. Lower layer systems and network management ensemble for TB/TC/TD/TE/RB/RC/profiles
    This standard has been withdrawn as it is identical to ISO/IEC ISP 15122-2:1999 which has been withdrawn by ISO/IEC/JTC 1
  • BS ISO/IEC ISP 15125-7:1998 Information technology. International Standardized Profiles ADYnn. OSI Directory. ADY43. DSA to DSA authentication
    This standard has been withdrawn as it is identical to ISO/IEC ISP 15125-7:1998 which has been withdrawn by ISO/IEC/JTC 1
  • BS ISO 15161:2001 Guidelines on the application of ISO 9001:2000 for the food and drink industry
    This standard has been withdrawn as it is identical to ISO 15161:2001 which has been withdrawn by ISO/TC 34
  • BS ISO/IEC 15289:2006 Systems and software engineering. Content of systems and software life cycle process information products (documentation)
    Superseded by BS ISO/IEC/IEEE 15289:2011
  • BS ISO/IEC TR 15580:2001 Information technology. Programming languages. Fortran. Floating-point exception handling
    This standard has been withdrawn as it is identical to ISO/IEC TR 15580:2001 which has been withdrawn by ISO/IEC/JTC 1/SC 22/WG 5
  • BS ISO/IEC TR 15581:2001 Information technology. Programming languages. Fortran. Enhanced data type facilities
    This standard has been withdrawn as it is identical to ISO/IEC TR 15581:2001 which has been withdraw/sn by ISO/IEC/JTC 1/SC 22/WG 5
  • BS ISO/IEC TR 15846:1998 Information technology. Software life cycle processes. Configuration management
    This standard has been withdrawn as it is identical to ISO/IEC TR 15846:1998 which has been withdrawn by ISO/IEC/JTC 1/SC 7
  • BS ISO 15929:2002 Graphic technology. Prepress digital data exchange. Guidelines and principles for the development of PDF/X standards
    This standard has been withdrawn as it is identical to ISO 15929:2002 which has been withdrawn by ISO/TC 130/WG 2
  • BS ISO/IEC TR 15947:2002 Information technology. Security techniques. IT intrusion detection framework
    This standard has been withdrawn as it is identical to ISO/IEC TR 15947:2002 which has been withdrawn by ISO/IEC/JTC 1/SC 27/WG 1
  • BS ISO 15994:2005 Graphic technology. Testing of prints. Visual lustre
    This standard has been withdrawn as it is identical to ISO 15994:2005 which has been withdrawn by ISO/TC 130/WG 4
  • BS ISO 17433:2003 Space data and information transfer systems. Packet telemetry services
    This standard has been withdrawn as it is identical to ISO 17433:2003 which has been withdrawn by ISO/TC 20/SC 13
  • PD 3542:1998 Standards and quality management. An integrated approach
    This standard has been withdrawn as PD 6495 is withdrawn as the IFAN document upon which it is based has been withdrawn
  • PD 6460:1971 Collected amendments to the CV7000 specifications for semiconductors adopted as British Standards (9300C series)
    This standard has been withdrawn as it is no longer used
  • BS 2L 500:1973 Procedure for inspection and testing of wrought magnesium-base alloys
    Superseded by BS 3L 500:2011
  • BS 4L 100:1993 Procedure for inspection, testing and acceptance of wrought aluminium and aluminium alloys
    Superseded by BS 5L 100:2011
  • BS 4L 101:1990 Procedure for inspection, testing and acceptance of aluminium-base and magnesium-base ingots and castings
    Superseded by BS 5L 101:2011
  • BS AU 178a:1992 Specification for road vehicle safety glass
    This standard has been withdrawn as Vehicle Safety glazing is now dealt with in ECE Regulation 43 which incorporates the requirements of the Global Technical Regulation No.6
  • BS MA 7:1983 Specification for manholes with bolted covers
    Superseded by BS ISO 5894:1999
  • BS Z 1:1997 (ISO 11103:1991) Space data and information transfer systems. Radio metric and orbit data
    This standard has been withdrawn as it is identical to ISO 11103:1991 which has been withdrawn by ISO/TC 20/SC 13
  • BS 3TA 12:2009 Specification for forging stock of titanium-aluminium-vanadium alloy (tensile strength 900-1160 MPa) (limiting ruling section 150 mm)
    Superseded by BS EN 3310:2011
  • CP 3010:1972 Code of practice for safe use of cranes (mobile cranes, tower cranes and derrick cranes)
    Superseded by BS 7121-1:1989, BS 7121-2:1991 and BS 7121-3:2000

Published in international.