ASTM STANDARDS

To purchase PDF or hard copy ASTM Standards, please email enquiries@standards.co.nz or call 0800 782 632 during business hours.

  • A20/A20M Standard Specification for General Requirements for Steel Plates for Pressure Vessels
    Revised to A20/A20M-11 developed by Committee A01.11, ASTM BOS Volume 01.04.
  • A29/A29M Standard Specification for Steel Bars, Carbon and Alloy, Hot-Wrought, General Requirements for
    Revised to A29/A29M-11a developed by Committee A01.15, ASTM BOS Volume 01.05.
  • A90/A90M Standard Test Method for Weight [Mass] of Coating on Iron and Steel Articles with Zinc or Zinc-Alloy Coatings
    Revised to A90/A90M-11 developed by Committee A05.07, ASTM BOS Volume 01.06.
  • A182/A182M Standard Specification for Forged or Rolled Alloy and Stainless Steel Pipe Flanges, Forged Fittings, and Valves and Parts for High-Temperature Service
    Revised to A182/A182M-11a developed by Committee A01.22, ASTM BOS Volume 01.01.
  • A184/A184M Standard Specification for Welded Deformed Steel Bar Mats for Concrete Reinforcement
    Reapproved, available as A184/A184M-06(2011) developed by Committee A01.05, ASTM BOS Volume 01.04.
  • A213/A213M Standard Specification for Seamless Ferritic and Austenitic Alloy-Steel Boiler, Superheater, and Heat-Exchanger Tubes
    Revised to A213/A213M-11a developed by Committee A01.10, ASTM BOS Volume 01.01.
  • A264 Standard Specification for Stainless Chromium-Nickel Steel-Clad Plate
    Revised to A264-11 developed by Committee A01.11, ASTM BOS Volume 01.04.
  • A266/A266M Standard Specification for Carbon Steel Forgings for Pressure Vessel Components
    Revised to A266/A266M-11 developed by Committee A01.06, ASTM BOS Volume 01.05.
  • A304 Standard Specification for Carbon and Alloy Steel Bars Subject to End-Quench Hardenability Requirements
    Revised to A304-11 developed by Committee A01.15, ASTM BOS Volume 01.05.
  • A335/A335M Standard Specification for Seamless Ferritic Alloy-Steel Pipe for High-Temperature Service
    Revised to A335/A335M-11 developed by Committee A01.10, ASTM BOS Volume 01.01.
  • A341/A341M Standard Test Method for Direct Current Magnetic Properties of Materials Using D-C Permeameters and the Ballistic Test Methods
    Reapproved, available as A341/A341M-00(2011) developed by Committee A06.01, ASTM BOS Volume 03.04.
  • A350/A350M Standard Specification for Carbon and Low-Alloy Steel Forgings, Requiring Notch Toughness Testing for Piping Components
    Revised to A350/A350M-11 developed by Committee A01.22, ASTM BOS Volume 01.01.
  • A369/A369M Standard Specification for Carbon and Ferritic Alloy Steel Forged and Bored Pipe for High-Temperature Service
    Revised to A369/A369M-11 developed by Committee A01.10, ASTM BOS Volume 01.01.
  • A385/A385M Standard Practice for Providing High-Quality Zinc Coatings (Hot-Dip)
    Revised to A385/A385M-11 developed by Committee A05.13, ASTM BOS Volume 01.06.
  • A390 Standard Specification for Zinc-Coated (Galvanized) Steel Poultry Fence Fabric (Hexagonal and Straight Line)
    Reapproved, available as A390-06(2011) developed by Committee A05.12, ASTM BOS Volume 01.06.
  • A394 Standard Specification for Steel Transmission Tower Bolts, Zinc-Coated and Bare
    Editorially changed, available as A394-08e1 developed by Committee F16.02, ASTM BOS Volume 01.08.
  • A403/A403M Standard Specification for Wrought Austenitic Stainless Steel Piping Fittings
    Revised to A403/A403M-11 developed by Committee A01.22, ASTM BOS Volume 01.01.
  • A490M Standard Specification for High-Strength Steel Bolts, Classes 10.9 and 10.9.3, for Structural Steel Joints (Metric)
    Editorially changed, available as A490M-10e1 developed by Committee F16.02, ASTM BOS Volume 01.08.
  • A511/A511M Standard Specification for Seamless Stainless Steel Mechanical Tubing
    Revised to A511/A511M-11 developed by Committee A01.10, ASTM BOS Volume 01.01.
  • A554 Standard Specification for Welded Stainless Steel Mechanical Tubing
    Revised to A554-11 developed by Committee A01.10, ASTM BOS Volume 01.01.
  • A568/A568M Standard Specification for Steel, Sheet, Carbon, Structural, and High-Strength, Low-Alloy, Hot-Rolled and Cold-Rolled, General Requirements for
    Revised to A568/A568M-11b developed by Committee A01.19, ASTM BOS Volume 01.03.
  • A595/A595M Standard Specification for Steel Tubes, Low-Carbon or High-Strength Low-Alloy, Tapered for Structural Use
    Revised to A595/A595M-11 developed by Committee A01.09, ASTM BOS Volume 01.01.
  • A653/A653M Standard Specification for Steel Sheet, Zinc-Coated (Galvanized) or Zinc-Iron Alloy-Coated (Galvannealed) by the Hot-Dip Process
    Revised to A653/A653M-11 developed by Committee A05.11, ASTM BOS Volume 01.06.
  • A664 Standard Practice for Identification of Standard Electrical Steel Grades in ASTM Specifications
    Revised to A664-11 developed by Committee A06.02, ASTM BOS Volume 03.04.
  • A704/A704M Standard Specification for Welded Steel Plain Bar or Rod Mats for Concrete Reinforcement
    Reapproved, available as A704/A704M-06(2011) developed by Committee A01.05, ASTM BOS Volume 01.04.
  • A720/A720M Standard Test Method for Ductility of Nonoriented Electrical Steel
    Reapproved, available as A720/A720M-02(2011) developed by Committee A06.01, ASTM BOS Volume 03.04.
  • A721/A721M Standard Test Method for Ductility of Oriented Electrical Steel
    Reapproved, available as A721/A721M-02(2011) developed by Committee A06.01, ASTM BOS Volume 03.04.
  • A727/A727M Standard Specification for Carbon Steel Forgings for Piping Components with Inherent Notch Toughness
    Revised to A727/A727M-11 developed by Committee A01.22, ASTM BOS Volume 01.01.
  • A729/A729M Standard Specification for Alloy Steel Axles, Heat-Treated, for Mass Transit and Electric Railway Service
    Editorially changed, available as A729/A729M-09e1 developed by Committee A01.06, ASTM BOS Volume 01.05.
  • A741 Standard Specification for Metallic-Coated Steel Wire Rope and Fittings for Highway Guardrail
    Revised (with title change) to A741-11 developed by Committee A05.12, ASTM BOS Volume 01.06.
  • A744/A744M Standard Specification for Castings, Iron-Chromium-Nickel, Corrosion Resistant, for Severe Service
    Editorially changed, available as A744/A744M-10e1 developed by Committee A01.18, ASTM BOS Volume 01.02.
  • A754/A754M Standard Test Method for Coating Weight (Mass) of Metallic Coatings on Steel by X-Ray Fluorescence
    Revised to A754/A754M-11 developed by Committee A05.07, ASTM BOS Volume 01.06.
  • A755/A755M Standard Specification for Steel Sheet, Metallic Coated by the Hot-Dip Process and Prepainted by the Coil-Coating Process for Exterior Exposed Building Products
    Revised to A755/A755M-11 developed by Committee A05.11, ASTM BOS Volume 01.06.
  • A788/A788M Standard Specification for Steel Forgings, General Requirements
    Revised to A788/A788M-11 developed by Committee A01.06, ASTM BOS Volume 01.05.
  • A820/A820M Standard Specification for Steel Fibers for Fiber-Reinforced Concrete
    Revised to A820/A820M-11 developed by Committee A01.05, ASTM BOS Volume 01.04.
  • A878/A878M Standard Specification for Steel Wire, Modified Chromium Vanadium Valve Spring Quality
    Reapproved, available as A878/A878M-05(2011) developed by Committee A01.03, ASTM BOS Volume 01.03.
  • A912/A912M Standard Test Method for Alternating-Current Magnetic Properties of Amorphous Materials at Power Frequencies Using Wattmeter-Ammeter-Voltmeter Method with Toroidal Specimens
    Revised to A912/A912M-11 developed by Committee A06.01, ASTM BOS Volume 03.04.
  • A913/A913M Standard Specification for High-Strength Low-Alloy Steel Shapes of Structural Quality, Produced by Quenching and Self-Tempering Process
    Revised to A913/A913M-11 developed by Committee A01.02, ASTM BOS Volume 01.04.
  • A918 Standard Specification for Steel Sheet, Zinc-Nickel Alloy Coated by the Electrolytic Process for Applications Requiring Designation of the Coating Mass on Each Surface
    Reapproved, available as A918-06(2011) developed by Committee A05.11, ASTM BOS Volume 01.06.
  • A950/A950M Standard Specification for Fusion-Bonded Epoxy-Coated Structural Steel H-Piles and Sheet Piling
    Revised to A950/A950M-11 developed by Committee A01.02, ASTM BOS Volume 01.04.
  • A951/A951M Standard Specification for Steel Wire for Masonry Joint Reinforcement
    Revised to A951/A951M-11 developed by Committee A01.05, ASTM BOS Volume 01.04.
  • A955/A955M Standard Specification for Deformed and Plain Stainless-Steel Bars for Concrete Reinforcement
    Editorially changed, available as A955/A955M-11e1 developed by Committee A01.05, ASTM BOS Volume 01.04.
  • A980/A980M Standard Specification for Steel, Sheet, Carbon, Ultra High Strength Cold Rolled
    Revised (with designation change) to A980/A980M-11 developed by Committee A01.19, ASTM BOS Volume 01.03.
  • A1003/A1003M Standard Specification for Steel Sheet, Carbon, Metallic- and Nonmetallic-Coated for Cold-Formed Framing Members
    Editorially changed, available as A1003/A1003M-11e1 developed by Committee A05.11, ASTM BOS Volume 01.06.
  • A1060/A1060M Standard Specification for Zinc-Coated (Galvanized) Steel Welded Wire Reinforcement, Plain and Deformed, for Concrete
    Revised to A1060/A1060M-11 developed by Committee A01.05, ASTM BOS Volume 01.04.
  • A1063/A1063M Standard Specification for Steel Sheet, Twin-Roll Cast, Zinc-Coated (Galvanized) by the Hot-Dip Process
    Revised to A1063/A1063M-11a developed by Committee A05.11, ASTM BOS Volume 01.06.
  • A1074-11 Standard Specification for Hot Tin and Hot Tin/Lead Dip on Ferrous and Non-Ferrous Metals
    New standard, now available. ASTM BOS Volume 01.06.
  • B96/B96M Standard Specification for Copper-Silicon Alloy Plate, Sheet, Strip, and Rolled Bar for General Purposes and Pressure Vessels
    Revised to B96/B96M-11 developed by Committee B05.01, ASTM BOS Volume 02.01.
  • B99/B99M Standard Specification for Copper-Silicon Alloy Wire for General Applications
    Revised to B99/B99M-11 developed by Committee B05.02, ASTM BOS Volume 02.01.
  • B111/B111M Standard Specification for Copper and Copper-Alloy Seamless Condenser Tubes and Ferrule Stock
    Revised to B111/B111M-11 developed by Committee B05.04, ASTM BOS Volume 02.01.
  • B117 Standard Practice for Operating Salt Spray (Fog) Apparatus
    Revised to B117-11 developed by Committee G01.05, ASTM BOS Volume 03.02.
  • B121/B121M Standard Specification for Leaded Brass Plate, Sheet, Strip, and Rolled Bar
    Revised to B121/B121M-11 developed by Committee B05.01, ASTM BOS Volume 02.01.
  • B122/B122M Standard Specification for Copper-Nickel-Tin Alloy, Copper-Nickel-Zinc Alloy (Nickel Silver), and Copper-Nickel Alloy Plate, Sheet, Strip, and Rolled Bar
    Revised to B122/B122M-11 developed by Committee B05.01, ASTM BOS Volume 02.01.
  • B124/B124M Standard Specification for Copper and Copper Alloy Forging Rod, Bar, and Shapes
    Revised to B124/B124M-11b developed by Committee B05.02, ASTM BOS Volume 02.01.
  • B159/B159M Standard Specification for Phosphor Bronze Wire
    Revised to B159/B159M-11 developed by Committee B05.02, ASTM BOS Volume 02.01.
  • B163 Standard Specification for Seamless Nickel and Nickel Alloy (UNS N06845) Condenser and Heat-Exchanger Tubes
    Revised (with title change) to B163-11 developed by Committee B02.07, ASTM BOS Volume 02.04.
  • B166 Standard Specification for Nickel-Chromium-Iron Alloys (UNS N06600, N06601, N06603, N06690, N06693, N06025, N06045, and N06696),* Nickel-Chromium-Cobalt-Molybdenum Alloy (UNS N06617), and Nickel-Iron-Chromium-Tungsten Alloy (UNS N06674) Rod, Bar,
    Revised (with title change) to B166-11 developed by Committee B02.07, ASTM BOS Volume 02.04.
  • B167 Standard Specification for Nickel-Chromium-Iron Alloys (UNS N06600, N06601, N06603, N06690, N06693, N06025, N06045, and N06696),* Nickel-Chromium-Cobalt-Molybdenum Alloy (UNS N06617), and Nickel-Iron-Chromium-Tungsten Alloy (UNS N06674) Seamless Pipe an
    Revised (with title change) to B167-11 developed by Committee B02.07, ASTM BOS Volume 02.04.
  • B168 Standard Specification for Nickel-Chromium-Iron Alloys (UNS N06600, N06601, N06603, N06690, N06693, N06025, N06045, and N06696), Nickel-Chromium-Cobalt-Molybdenum Alloy (UNS N06617), and Nickel-Iron-Chromium-Tungsten Alloy (UNS N06674) Plate, Sheet,
    Revised (with title change) to B168-11 developed by Committee B02.07, ASTM BOS Volume 02.04.
  • B214 Standard Test Method for Sieve Analysis of Metal Powders
    Reapproved, available as B214-07(2011) developed by Committee B09.02, ASTM BOS Volume 02.05.
  • B232/B232M Standard Specification for Concentric-Lay-Stranded Aluminum Conductors, Coated-Steel Reinforced (ACSR)
    Revised to B232/B232M-11 developed by Committee B01.07, ASTM BOS Volume 02.03.
  • B271 Standard Specification for Copper-Base Alloy Centrifugal Castings
    Revised to B271-11 developed by Committee B05.05, ASTM BOS Volume 02.01.
  • B344 Standard Specification for Drawn or Rolled Nickel-Chromium and Nickel-Chromium-Iron Alloys for Electrical Heating Elements
    Has been reinstated, with revision to B344-11 developed by Committee B02.10, ASTM BOS Volume 02.04.
  • B417 Standard Test Method for Apparent Density of Non-Free-Flowing Metal Powders Using the Carney Funnel
    Revised (with title change) to B417-11 developed by Committee B09.02, ASTM BOS Volume 02.05.
  • B423 Standard Specification for Nickel-Iron-Chromium-Molybdenum-Copper Alloy (UNS N08825, N08221, and N06845) Seamless Pipe and Tube
    Revised to B423-11 developed by Committee B02.07, ASTM BOS Volume 02.04.
  • B424 Standard Specification for Ni-Fe-Cr-Mo-Cu Alloy (UNS N08825, UNS N08221, and UNS N06845) Plate, Sheet, and Strip
    Revised to B424-11 developed by Committee B02.07, ASTM BOS Volume 02.04.
  • B453/B453M Standard Specification for Copper-Zinc-Lead Alloy (Leaded-Brass) Rod, Bar, and Shapes
    Revised to B453/B453M-11 developed by Committee B05.02, ASTM BOS Volume 02.01.
  • B465 Standard Specification for Copper-Iron Alloy Plate, Sheet, Strip, and Rolled Bar
    Revised to B465-11 developed by Committee B05.01, ASTM BOS Volume 02.01.
  • B504 Standard Test Method for Measurement of Thickness of Metallic Coatings by the Coulometric Method
    Reapproved, available as B504-90(2011) developed by Committee B08.10, ASTM BOS Volume 02.05.
  • B505/B505M Standard Specification for Copper Alloy Continuous Castings
    Revised to B505/B505M-11 developed by Committee B05.05, ASTM BOS Volume 02.01.
  • B592 Standard Specification for Copper-Zinc-Aluminum-Cobalt Alloy, Copper-Zinc-Tin-Iron Alloy Plate, Sheet, Strip, and Rolled Bar
    Revised to B592-11 developed by Committee B05.01, ASTM BOS Volume 02.01.
  • B608 Standard Specification for Welded Copper-Alloy Pipe
    Revised to B608-11 developed by Committee B05.04, ASTM BOS Volume 02.01.
  • B633 Standard Specification for Electrodeposited Coatings of Zinc on Iron and Steel
    Revised to B633-11 developed by Committee B08.08.04, ASTM BOS Volume 02.05.
  • B747 Standard Specification for Copper-Zirconium Alloy Sheet and Strip
    Revised to B747-11 developed by Committee B05.01, ASTM BOS Volume 02.01.
  • B761 Standard Test Method for Particle Size Distribution of Metal Powders and Related Compounds by X-Ray Monitoring of Gravity Sedimentation
    Reapproved, available as B761-06(2011) developed by Committee B09.03, ASTM BOS Volume 02.05.
  • B768 Standard Specification for Copper-Cobalt-Beryllium Alloy and Copper-Nickel-Beryllium Alloy Strip and Sheet
    Revised to B768-11 developed by Committee B05.01, ASTM BOS Volume 02.01.
  • B771 Standard Test Method for Short Rod Fracture Toughness of Cemented Carbides
    Revised to B771-11 developed by Committee B09.06, ASTM BOS Volume 02.05.
  • B830 Standard Specification for Uniform Test Methods and Frequency
    Revised to B830-11 developed by Committee B01.02, ASTM BOS Volume 02.03.
  • B944 Standard Specification for Copper-Beryllium Welded Heat Exchanger and Condenser Tube (UNS No. C17510)
    Revised to B944-11 developed by Committee B05.04, ASTM BOS Volume 02.01.
  • B950 Standard Guide for Editorial Procedures and Form of Product Specifications for Copper and Copper Alloys
    Revised to B950-11a developed by Committee B05.91, ASTM BOS Volume 02.01.
  • B967/B967M Standard Specification for Copper-Zinc-Tin-Bismuth Alloy Rod, Bar and Wire
    Revised to B967/B967M-11a developed by Committee B05.02, ASTM BOS Volume 02.01.
  • C39/C39M Standard Test Method for Compressive Strength of Cylindrical Concrete Specimens
    Revised to C39/C39M-11a developed by Committee C09.61, ASTM BOS Volume 04.02.
  • C109/C109M Standard Test Method for Compressive Strength of Hydraulic Cement Mortars (Using 2-in. or [50-mm] Cube Specimens)
    Revised to C109/C109M-11a developed by Committee C01.27, ASTM BOS Volume 04.01.
  • C179 Standard Test Method for Drying and Firing Linear Change of Refractory Plastic and Ramming Mix Specimens
    Revised to C179-11 developed by Committee C08.09, ASTM BOS Volume 15.01.
  • C181 Standard Test Method for Workability Index of Fireclay and High-Alumina Refractory Plastics
    Revised to C181-11 developed by Committee C08.09, ASTM BOS Volume 15.01.
  • C187 Standard Test Method for Amount of Water Required for Normal Consistency of Hydraulic Cement Paste
    Editorially changed, available as C187-11e1 developed by Committee C01.22, ASTM BOS Volume 04.01.
  • C233/C233M Standard Test Method for Air-Entraining Admixtures for Concrete
    Revised to C233/C233M-11 developed by Committee C09.23, ASTM BOS Volume 04.02.
  • C393/C393M Standard Test Method for Core Shear Properties of Sandwich Constructions by Beam Flexure
    Revised to C393/C393M-11 developed by Committee D30.09, ASTM BOS Volume 15.03.
  • C457/C457M Standard Test Method for Microscopical Determination of Parameters of the Air-Void System in Hardened Concrete
    Revised to C457/C457M-11 developed by Committee C09.65, ASTM BOS Volume 04.02.
  • C490/C490M Standard Practice for Use of Apparatus for the Determination of Length Change of Hardened Cement Paste, Mortar, and Concrete
    Revised to C490/C490M-11 developed by Committee C01.95, ASTM BOS Volume 04.01.
  • C513 Standard Test Method for Obtaining and Testing Specimens of Hardened Lightweight Insulating Concrete for Compressive Strength
    Has been reinstated, with revision to C513-11 developed by Committee C09.21, ASTM BOS Volume 04.02.
  • C578 Standard Specification for Rigid, Cellular Polystyrene Thermal Insulation
    Revised to C578-11a developed by Committee C16.22, ASTM BOS Volume 04.06.
  • C586 Standard Test Method for Potential Alkali Reactivity of Carbonate Rocks as Concrete Aggregates (Rock-Cylinder Method)
    Revised to C586-11 developed by Committee C09.26, ASTM BOS Volume 04.02.
  • C645 Standard Specification for Nonstructural Steel Framing Members
    Revised to C645-11a developed by Committee C11.02, ASTM BOS Volume 04.01.
  • C874 Standard Test Method for Rotary Slag Testing of Refractory Materials
    Revised to C874-11a developed by Committee C08.04, ASTM BOS Volume 15.01.
  • C896 Standard Terminology Relating to Clay Products
    Revised to C896-11 developed by Committee C04.10, ASTM BOS Volume 04.05.
  • C926 Standard Specification for Application of Portland Cement-Based Plaster
    Revised to C926-11a developed by Committee C11.03, ASTM BOS Volume 04.01.
  • C955 Standard Specification for Load-Bearing (Transverse and Axial) Steel Studs, Runners (Tracks), and Bracing or Bridging for Screw Application of Gypsum Panel Products and Metal Plaster Bases
    Revised to C955-11b developed by Committee C11.02, ASTM BOS Volume 04.01.
  • C1036 Standard Specification for Flat Glass
    Revised to C1036-11 developed by Committee C14.08, ASTM BOS Volume 15.02.
  • C1063 Standard Specification for Installation of Lathing and Furring to Receive Interior and Exterior Portland Cement-Based Plaster
    Revised to C1063-11a developed by Committee C11.03, ASTM BOS Volume 04.01.
  • C1157/C1157M Standard Performance Specification for Hydraulic Cement
    Revised to C1157/C1157M-11 developed by Committee C01.10, ASTM BOS Volume 04.01.
  • C1173 Standard Specification for Flexible Transition Couplings for Underground Piping Systems
    Editorially changed, available as C1173-10e1 developed by Committee A04.75, ASTM BOS Volume 01.02.
  • C1178/C1178M Standard Specification for Coated Glass Mat Water-Resistant Gypsum Backing Panel
    Revised to C1178/C1178M-11 developed by Committee C11.01, ASTM BOS Volume 04.01.
  • C1193 Standard Guide for Use of Joint Sealants
    Revised to C1193-11a developed by Committee C24.10, ASTM BOS Volume 04.07.
  • C1264 Standard Specification for Sampling, Inspection, Rejection, Certification, Packaging, Marking, Shipping, Handling, and Storage of Gypsum Panel Products
    Revised (with title change) to C1264-11 developed by Committee C11.01, ASTM BOS Volume 04.01.
  • C1283 Standard Practice for Installing Clay Flue Lining
    Revised to C1283-11 developed by Committee C04.20, ASTM BOS Volume 04.05.
  • C1313/C1313M Standard Specification for Sheet Radiant Barriers for Building Construction Applications
    Revised to C1313/C1313M-11 developed by Committee C16.21, ASTM BOS Volume 04.06.
  • C1423 Standard Guide for Selecting Jacketing Materials for Thermal Insulation
    Reapproved, available as C1423-98(2011) developed by Committee C16.40, ASTM BOS Volume 04.06.
  • C1496 Standard Guide for Assessment and Maintenance of Exterior Dimension Stone Masonry Walls and Facades
    Revised to C1496-11 developed by Committee C18.07, ASTM BOS Volume 04.07.
  • C1515 Standard Guide for Cleaning of Exterior Dimension Stone, Vertical And Horizontal Surfaces, New or Existing
    Revised to C1515-11 developed by Committee C18.07, ASTM BOS Volume 04.07.
  • C1556 Standard Test Method for Determining the Apparent Chloride Diffusion Coefficient of Cementitious Mixtures by Bulk Diffusion
    Revised to C1556-11 developed by Committee C09.66, ASTM BOS Volume 04.02.
  • C1577 Standard Specification for Precast Reinforced Concrete Monolithic Box Sections for Culverts, Storm Drains, and Sewers Designed According to AASHTO LRFD
    Revised to C1577-11a developed by Committee C13.07, ASTM BOS Volume 04.05.
  • C1586 Standard Guide for Quality Assurance of Mortars
    Reapproved, available as C1586-05(2011) developed by Committee C12.03, ASTM BOS Volume 04.05.
  • C1619 Standard Specification for Elastomeric Seals for Joining Concrete Structures
    Revised to C1619-11 developed by Committee C13.08, ASTM BOS Volume 04.05.
  • C1651 Standard Test Method for Measurement of Roll Wave Optical Distortion in Heat-Treated Flat Glass
    Revised to C1651-11 developed by Committee C14.11, ASTM BOS Volume 15.02.
  • C1675-11 Standard Practice for Installation of Precast Reinforced Concrete Monolithic Box Sections for Culverts, Storm Drains, and Sewers
    New standard, now available. ASTM BOS Volume 04.05.
  • C1713 Standard Specification for Mortars for the Repair of Historic Masonry
    Revised to C1713-11 developed by Committee C12.03, ASTM BOS Volume 04.05.
  • C1722-11 Standard Guide for Repair and Restoration of Dimension Stone
    New standard, now available. ASTM BOS Volume 04.07.
  • C1738 Standard Practice for High-Shear Mixing of Hydraulic Cement Paste
    Revised to C1738-11a developed by Committee C01.22, ASTM BOS Volume 04.01.
  • C1745/C1745M-11 Standard Test Method for Measurement of Hydraulic Characteristics of Hydrodynamic Stormwater Separators and Underground Settling Devices
    New standard, now available. ASTM BOS Volume 04.05.
  • D93 Standard Test Methods for Flash Point by Pensky-Martens Closed Cup Tester
    Revised to D93-11 developed by Committee D02.08, ASTM BOS Volume 05.01.
  • D129 Standard Test Method for Sulfur in Petroleum Products (General High Pressure Decomposition Device Method)
    Revised (with title change) to D129-11 developed by Committee D02.03, ASTM BOS Volume 05.01.
  • D331 Standard Specification for 2-Ethoxyethanol
    Revised to D331-11 developed by Committee D01.35, ASTM BOS Volume 06.04.
  • D346/D346M Standard Practice for Collection and Preparation of Coke Samples for Laboratory Analysis
    Revised (with designation change) to D346/D346M-11 developed by Committee D05.23, ASTM BOS Volume 05.06.
  • D660 Standard Test Method for Evaluating Degree of Checking of Exterior Paints
    Reapproved, available as D660-93(2011) developed by Committee D01.25, ASTM BOS Volume 06.01.
  • D661 Standard Test Method for Evaluating Degree of Cracking of Exterior Paints
    Reapproved, available as D661-93(2011) developed by Committee D01.25, ASTM BOS Volume 06.01.
  • D662 Standard Test Method for Evaluating Degree of Erosion of Exterior Paints
    Reapproved, available as D662-93(2011) developed by Committee D01.25, ASTM BOS Volume 06.01.
  • D721 Standard Test Method for Oil Content of Petroleum Waxes
    Reapproved, available as D721-06(2011) developed by Committee D02.10.0A, ASTM BOS Volume 05.01.
  • D770 Standard Specification for Isopropyl Alcohol
    Revised to D770-11 developed by Committee D01.35, ASTM BOS Volume 06.04.
  • D772 Standard Test Method for Evaluating Degree of Flaking (Scaling) of Exterior Paints
    Reapproved, available as D772-86(2011) developed by Committee D01.25, ASTM BOS Volume 06.01.
  • D808 Standard Test Method for Chlorine in New and Used Petroleum Products (High Pressure Decomposition Device Method)
    Revised (with title change) to D808-11 developed by Committee D02.03, ASTM BOS Volume 05.01.
  • D892 Standard Test Method for Foaming Characteristics of Lubricating Oils
    Revised to D892-11a developed by Committee D02.06, ASTM BOS Volume 05.01.
  • D976 Standard Test Method for Calculated Cetane Index of Distillate Fuels
    Reapproved, available as D976-06(2011) developed by Committee D02.E0, ASTM BOS Volume 05.01.
  • D1007 Standard Specification for sec-Butyl Alcohol
    Revised to D1007-11 developed by Committee D01.35, ASTM BOS Volume 06.04.
  • D1121 Standard Test Method for Reserve Alkalinity of Engine Coolants and Antirusts
    Revised to D1121-11 developed by Committee D15.04, ASTM BOS Volume 15.05.
  • D1265 Standard Practice for Sampling Liquefied Petroleum (LP) Gases, Manual Method
    Revised to D1265-11 developed by Committee D02.H0, ASTM BOS Volume 05.01.
  • D1287 Standard Test Method for pH of Engine Coolants and Antirusts
    Revised to D1287-11 developed by Committee D15.04, ASTM BOS Volume 15.05.
  • D1596 Standard Test Method for Dynamic Shock Cushioning Characteristics of Packaging Material
    Reapproved, available as D1596-97(2011) developed by Committee D10.13, ASTM BOS Volume 15.10.
  • D1599 Standard Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings
    Reapproved, available as D1599-99(2011) developed by Committee F17.40, ASTM BOS Volume 08.04.
  • D1655 Standard Specification for Aviation Turbine Fuels
    Revised to D1655-11b developed by Committee D02.J0.01, ASTM BOS Volume 05.01.
  • D1719 Standard Specification for Isobutyl Alcoholl
    Revised to D1719-11 developed by Committee D01.35, ASTM BOS Volume 06.04.
  • D1837 Standard Test Method for Volatility of Liquefied Petroleum (LP) Gases
    Revised to D1837-11 developed by Committee D02.H0, ASTM BOS Volume 05.01.
  • D1838 Standard Test Method for Copper Strip Corrosion by Liquefied Petroleum (LP) Gases
    Revised to D1838-11 developed by Committee D02.H0, ASTM BOS Volume 05.01.
  • D2047 Standard Test Method for Static Coefficient of Friction of Polish-Coated Flooring Surfaces as Measured by the James Machine
    Revised to D2047-11 developed by Committee D21.06, ASTM BOS Volume 15.04.
  • D2065 Standard Test Method for Determination of Edge Performance of Composite Wood Products Under Surfactant Accelerated Moisture Stress
    Reapproved, available as D2065-03(2011) developed by Committee D01.52, ASTM BOS Volume 06.02.
  • D2091 Standard Test Method for Print Resistance of Lacquers
    Reapproved, available as D2091-96(2011) developed by Committee D01.52, ASTM BOS Volume 06.02.
  • D2109 Standard Test Methods for Nonvolatile Matter in Halogenated Organic Solvents and Their Admixtures
    Reapproved, available as D2109-01(2011) developed by Committee D26.04, ASTM BOS Volume 15.05.
  • D2501 Standard Test Method for Calculation of Viscosity-Gravity Constant (VGC) of Petroleum Oils
    Revised to D2501-11 developed by Committee D02.04.0K, ASTM BOS Volume 05.01.
  • D2584 Standard Test Method for Ignition Loss of Cured Reinforced Resins
    Revised to D2584-11 developed by Committee D20.18, ASTM BOS Volume 08.01.
  • D2718 Standard Test Methods for Structural Panels in Planar Shear (Rolling Shear)
    Reapproved, available as D2718-00(2011) developed by Committee D07.03, ASTM BOS Volume 04.10.
  • D2786 Standard Test Method for Hydrocarbon Types Analysis of Gas-Oil Saturates Fractions by High Ionizing Voltage Mass Spectrometry
    Reapproved, available as D2786-91(2011) developed by Committee D02.04.0M, ASTM BOS Volume 05.01.
  • D2825 Standard Terminology Relating to Polishes and Related Materials
    Revised to D2825-11 developed by Committee D21.91, ASTM BOS Volume 15.04.
  • D2859 Standard Test Method for Ignition Characteristics of Finished Textile Floor Covering Materials
    Reapproved, available as D2859-06(2011) developed by Committee E05.22, ASTM BOS Volume 04.07.
  • D2989 Standard Test Method for Acidity-Alkalinity of Halogenated Organic Solvents and Their Admixtures
    Reapproved, available as D2989-01(2011) developed by Committee D26.04, ASTM BOS Volume 15.05.
  • D3023 Standard Practice for Determination of Resistance of Factory-Applied Coatings on Wood Products to Stains and Reagents
    Reapproved, available as D3023-98(2011) developed by Committee D01.52, ASTM BOS Volume 06.02.
  • D3043 Standard Test Methods for Structural Panels in Flexure
    Reapproved, available as D3043-00(2011) developed by Committee D07.03, ASTM BOS Volume 04.10.
  • D3044 Standard Test Method for Shear Modulus of Wood-Based Structural Panels
    Reapproved, available as D3044-94(2011) developed by Committee D07.03, ASTM BOS Volume 04.10.
  • D3139 Standard Specification for Joints for Plastic Pressure Pipes Using Flexible Elastomeric Seals
    Reapproved, available as D3139-98(2011) developed by Committee F17.20, ASTM BOS Volume 08.04.
  • D3171 Standard Test Methods for Constituent Content of Composite Materials
    Revised to D3171-11 developed by Committee D30.04, ASTM BOS Volume 15.03.
  • D3235 Standard Test Method for Solvent Extractables in Petroleum Waxes
    Reapproved, available as D3235-06(2011) developed by Committee D02.10.0A, ASTM BOS Volume 05.01.
  • D3239 Standard Test Method for Aromatic Types Analysis of Gas-Oil Aromatic Fractions by High Ionizing Voltage Mass Spectrometry
    Reapproved, available as D3239-91(2011) developed by Committee D02.04.0M, ASTM BOS Volume 05.01.
  • D3316 Standard Test Method for Stability of Perchloroethylene with Copper
    Reapproved, available as D3316-06(2011) developed by Committee D26.04, ASTM BOS Volume 15.05.
  • D3454 Standard Test Method for Radium-226 in Water
    Revised to D3454-11 developed by Committee D19.04, ASTM BOS Volume 11.02.
  • D3481 Standard Test Method for Manual Shelling Two-Piece Child-Resistant Closures That Are Activated by Two Simultaneous Dissimilar Motions
    Reapproved, available as D3481-01(2011) developed by Committee D10.32, ASTM BOS Volume 15.10.
  • D3501 Standard Test Methods for Wood-Based Structural Panels in Compression
    Reapproved, available as D3501-05a(2011) developed by Committee D07.03, ASTM BOS Volume 04.10.
  • D3531/D3531M Standard Test Method for Resin Flow of Carbon Fiber-Epoxy Prepreg
    Revised (with designation change) to D3531/D3531M-11 developed by Committee D30.03, ASTM BOS Volume 15.03.
  • D3611 Standard Practice for Accelerated Aging of Pressure-Sensitive Tapes
    Reapproved, available as D3611-06(2011) developed by Committee D10.14, ASTM BOS Volume 15.10.
  • D3622 Standard Specification for 1-Propanol (n-Propyl Alcohol)
    Revised to D3622-11 developed by Committee D01.35, ASTM BOS Volume 06.04.
  • D3654/D3654M Standard Test Methods for Shear Adhesion of Pressure-Sensitive Tapes
    Reapproved, available as D3654/D3654M-06(2011) developed by Committee D10.14, ASTM BOS Volume 15.10.
  • D3677 Standard Test Methods for Rubber - Identification by Infrared Spectrophotometry
    Editorially changed, available as D3677-10e1 developed by Committee D11.11, ASTM BOS Volume 09.01.
  • D3759/D3759M Standard Test Method for Breaking Strength and Elongation of Pressure-Sensitive Tape
    Reapproved, available as D3759/D3759M-05(2011) developed by Committee D10.14, ASTM BOS Volume 15.10.
  • D3811/D3811M Standard Test Method for Unwind Force of Pressure-Sensitive Tapes
    Reapproved, available as D3811/D3811M-96(2011) developed by Committee D10.14, ASTM BOS Volume 15.10.
  • D3815/D3815M Standard Practice for Accelerated Weathering of Pressure-Sensitive Tapes by Open-Flame Carbon-Arc Exposure Apparatus
    Reapproved, available as D3815/D3815M-05(2011) developed by Committee D10.14, ASTM BOS Volume 15.10.
  • D3833/D3833M Standard Test Method for Water Vapor Transmission of Pressure-Sensitive Tapes
    Reapproved, available as D3833/D3833M-96(2011) developed by Committee D10.14, ASTM BOS Volume 15.10.
  • D3948 Standard Test Method for Determining Water Separation Characteristics of Aviation Turbine Fuels by Portable Separometer
    Revised to D3948-11 developed by Committee D02.J0.05, ASTM BOS Volume 05.02.
  • D4049 Standard Test Method for Determining the Resistance of Lubricating Grease to Water Spray
    Reapproved, available as D4049-06(2011) developed by Committee D02.G0.06, ASTM BOS Volume 05.02.
  • D4079 Standard Specification for Vapor-Degreasing Grade Methylene Chloride
    Reapproved, available as D4079-00(2011) developed by Committee D26.02, ASTM BOS Volume 15.05.
  • D4080 Standard Specification for Trichloroethylene, Technical and Vapor-Degreasing Grade
    Reapproved, available as D4080-00(2011) developed by Committee D26.02, ASTM BOS Volume 15.05.
  • D4081 Standard Specification for Drycleaning-Grade Perchloroethylene
    Reapproved, available as D4081-00(2011) developed by Committee D26.06, ASTM BOS Volume 15.05.
  • D4418 Standard Practice for Receipt, Storage, and Handling of Fuels for Gas Turbines
    Reapproved, available as D4418-00(2011) developed by Committee D02.E0, ASTM BOS Volume 05.02.
  • D4504 Standard Specification for Molded Polyethylene Open-Head-Pails for Industrial Shipping of Nonhazardous Goods
    Reapproved, available as D4504-94(2011) developed by Committee D10.21, ASTM BOS Volume 15.10.
  • D4614 Standard Specification for Ethyl Acetate (All Grades)
    Revised to D4614-11 developed by Committee D01.35, ASTM BOS Volume 06.04.
  • D4678 Standard Practice for Rubber - Preparation, Testing, Acceptance, Documentation, and Use of Reference Materials
    Editorially changed, available as D4678-04(2009)e1 developed by Committee D11.20, ASTM BOS Volume 09.01.
  • D4701 Standard Specification for Technical Grade Methylene Chloride
    Reapproved, available as D4701-00(2011) developed by Committee D26.03, ASTM BOS Volume 15.05.
  • D5105 Standard Practice for Performing Accelerated Outdoor Weathering of Pressure-Sensitive Tapes Using Concentrated Natural Sunlight
    Reapproved, available as D5105-05(2011) developed by Committee D10.14, ASTM BOS Volume 15.10.
  • D5141 Standard Test Method for Determining Filtering Efficiency and Flow Rate of the Filtration Component of a Sediment Retention Device
    Revised (with title change) to D5141-11 developed by Committee D35.03, ASTM BOS Volume 04.13.
  • D5704 Standard Test Method for Evaluation of the Thermal and Oxidative Stability of Lubricating Oils Used for Manual Transmissions and Final Drive Axles
    Revised to D5704-11 developed by Committee D02.B0.03, ASTM BOS Volume 05.02.
  • D5889 Standard Practice for Quality Control of Geosynthetic Clay Liners
    Revised to D5889-11 developed by Committee D35.04, ASTM BOS Volume 04.13.
  • D6121 Standard Test Method for Evaluation of Load-Carrying Capacity of Lubricants Under Conditions of Low Speed and High Torque Used for Final Hypoid Drive Axles
    Revised to D6121-11 developed by Committee D02.B0.03, ASTM BOS Volume 05.02.
  • D6244 Standard Test Method for Vertical Compression of Geocomposite Pavement Panel Drains
    Reapproved, available as D6244-06(2011) developed by Committee D35.01, ASTM BOS Volume 04.13.
  • D6336 Standard Practice for Evaluation of Flushing Vehicles for Pigment Wetting Using a Vacuum Modified Sigma Blade Mixer
    Has been reinstated, with revision to D6336-11 developed by Committee D01.37, ASTM BOS Volume 06.03.
  • D6364 Standard Test Method for Determining Short-Term Compression Behavior of Geosynthetics
    Reapproved, available as D6364-06(2011) developed by Committee D35.01, ASTM BOS Volume 04.13.
  • D6492 Standard Practice for Detection of Hexavalent Chromium On Zinc and Zinc/Aluminum Alloy Coated Steel
    Reapproved, available as D6492-99(2011) developed by Committee D01.53, ASTM BOS Volume 06.02.
  • D6529 Standard Test Method for Operating Performance of Continuous Electrodeionization Systems on Feeds from 50–1000 ?S/cm
    Reinstated as D6529-11 developed by Committee D19.08, ASTM BOS Volume 11.02.
  • D6551/D6551M Standard Practice for Accelerated Weathering of Pressure-Sensitive Tapes by Xenon-Arc Exposure Apparatus
    Reapproved, available as D6551/D6551M-05(2011) developed by Committee D10.14, ASTM BOS Volume 15.10.
  • D6637 Standard Test Method for Determining Tensile Properties of Geogrids by the Single or Multi-Rib Tensile Method
    Revised to D6637-11 developed by Committee D35.01, ASTM BOS Volume 04.13.
  • D6643 Standard Test Method for Testing Wood-Base Panel Corner Impact Resistance
    Reapproved, available as D6643-01(2011) developed by Committee D07.03, ASTM BOS Volume 04.10.
  • D6647 Standard Test Method for Determination of Acid Soluble Iron Via Atomic Absorption
    Reapproved, available as D6647-01(2011) developed by Committee D28.02, ASTM BOS Volume 15.01.
  • D6675 Standard Practice for Salt-Accelerated Outdoor Cosmetic Corrosion Testing of Organic Coatings on Automotive Sheet Steel
    Reapproved, available as D6675-01(2011) developed by Committee D01.27, ASTM BOS Volume 06.01.
  • D6804 Standard Guide for Hand Hole Design in Corrugated Boxes
    Reapproved, available as D6804-02(2011) developed by Committee D10.27, ASTM BOS Volume 15.10.
  • D6817 Standard Specification for Rigid Cellular Polystyrene Geofoam
    Revised to D6817-11 developed by Committee D35.03, ASTM BOS Volume 04.13.
  • D6851 Standard Test Method for Determination of Contact pH with Activated Carbon
    Reapproved, available as D6851-02(2011) developed by Committee D28.02, ASTM BOS Volume 15.01.
  • D6916 Standard Test Method for Determining the Shear Strength Between Segmental Concrete Units (Modular Concrete Blocks)
    Reapproved, available as D6916-06c(2011) developed by Committee D35.01, ASTM BOS Volume 04.13.
  • D6987/D6987M Standard Test Method for Evaluation of Diesel Engine Oils in T-10 Exhaust Gas Recirculation Diesel Engine
    Revised to D6987/D6987M-11 developed by Committee D02.B0, ASTM BOS Volume 05.04.
  • D7001 Standard Specification for Geocomposites for Pavement Edge Drains and Other High-Flow Applications
    Reapproved, available as D7001-06(2011) developed by Committee D35.03, ASTM BOS Volume 04.13.
  • D7147 Standard Specification for Testing and Establishing Allowable Loads of Joist Hangers
    Revised to D7147-11 developed by Committee D07.05, ASTM BOS Volume 04.10.
  • D7228 Standard Test Method for Prediction of Asphalt-Bound Pavement Layer Temperatures
    Reapproved, available as D7228-06a(2011) developed by Committee E17.41, ASTM BOS Volume 04.03.
  • D7257 Standard Test Method for Automated Shelling Two-Piece Child-Resistant Closures That Are Activated by Two Simultaneous Dissimilar Motions
    Reapproved, available as D7257-06(2011) developed by Committee D10.32, ASTM BOS Volume 15.10.
  • D7307 Standard Practice for Sampling of Thermoplastic Traffic Marking Materials
    Reapproved, available as D7307-06(2011) developed by Committee D01.44, ASTM BOS Volume 06.02.
  • D7309 Standard Test Method for Determining Flammability Characteristics of Plastics and Other Solid Materials Using Microscale Combustion Calorimetry
    Revised to D7309-11 developed by Committee D20.30, ASTM BOS Volume 08.03.
  • D7430 Standard Practice for Mechanical Sampling of Coal
    Revised to D7430-11a developed by Committee D05.23, ASTM BOS Volume 05.06.
  • D7430 Standard Practice for Mechanical Sampling of Coal
    Editorially changed, available as D7430-11ae1 developed by Committee D05.23, ASTM BOS Volume 05.06.
  • D7575 Standard Test Method for Solvent-Free Membrane Recoverable Oil and Grease by Infrared Determination
    Revised to D7575-11 developed by Committee D19.06, ASTM BOS Volume 11.02.
  • D7701-11 Standard Test Method for Determining the Flow Rate of Water and Suspended Solids from a Geotextile Bag
    New standard, now available. ASTM BOS Volume 04.13.
  • D7714-11 Standard Specification for Glycerin Base Engine Coolant for Automobile and Light-Duty Service
    New standard, now available. ASTM BOS Volume 15.05.
  • D7716 Standard Test Method for Determination of Residual Methanol in Glycerin by Gas Chromatography
    Revised to D7716-11a developed by Committee D15.93, ASTM BOS Volume 15.05.
  • D7724-11 Standard Test Method for Carbon Black - Non-Dispersible Matter by Mechanical Flushing (NDM)
    New standard, now available. ASTM BOS Volume 09.01.
  • D7737-11 Standard Test Method for Individual Geogrid Junction Strength
    New standard, now available. ASTM BOS Volume 04.13.
  • D7747-11 Standard Test Method for Determining Integrity of Seams Produced Using Thermo-Fusion Methods for Reinforced Geomembranes by the Strip Tensile Method
    New standard, now available. ASTM BOS Volume 04.13.
  • D7749-11 Standard Test Method for Determining Integrity of Seams Produced Using Thermo-Fusion Methods for Reinforced Geomembranes by the Grab Method
    New standard, now available. ASTM BOS Volume 04.13.
  • D7751-11 Standard Test Method for Determination of Additive Elements in Lubricating Oils by EDXRF Analysis
    New standard, now available. ASTM BOS Volume 05.04.
  • E50 Standard Practices for Apparatus, Reagents, and Safety Considerations for Chemical Analysis of Metals, Ores, and Related Materials
    Revised to E50-11 developed by Committee E01.20, ASTM BOS Volume 03.05.
  • E84 Standard Test Method for Surface Burning Characteristics of Building Materials
    Revised to E84-11b developed by Committee E05.22, ASTM BOS Volume 04.07.
  • E122 Standard Practice for Calculating Sample Size to Estimate, With Specified Precision, the Average for a Characteristic of a Lot or Process
    Editorially changed, available as E122-09e1 developed by Committee E11.10, ASTM BOS Volume 14.02.
  • E128 Standard Test Method for Maximum Pore Diameter and Permeability of Rigid Porous Filters for Laboratory Use
    Reapproved, available as E128-99(2011) developed by Committee E41.01, ASTM BOS Volume 14.04.
  • E191 Standard Specification for Apparatus For Microdetermination of Carbon and Hydrogen in Organic and Organo-Metallic Compounds
    Reapproved, available as E191-64(2011) developed by Committee E41.01, ASTM BOS Volume 14.04.
  • E230/E230M Standard Specification and Temperature-Electromotive Force (emf) Tables for Standardized Thermocouples
    Editorially changed, available as E230/E230M-11e1 developed by Committee E20.04, ASTM BOS Volume 14.03.
  • E259 Standard Practice for Preparation of Pressed Powder White Reflectance Factor Transfer Standards for Hemispherical and Bi-Directional Geometries
    Reapproved, available as E259-06(2011) developed by Committee E12.02, ASTM BOS Volume 06.01.
  • E649 Standard Test Method for Bromine in Chlorine
    Reapproved, available as E649-00(2011) developed by Committee E15.02, ASTM BOS Volume 15.05.
  • E680 Standard Test Method for Drop Weight Impact Sensitivity of Solid-Phase Hazardous Materials
    Reapproved (with editorial change), available as E680-79(2011)e1 developed by Committee E27.02, ASTM BOS Volume 14.02.
  • E741 Standard Test Method for Determining Air Change in a Single Zone by Means of a Tracer Gas Dilution
    Revised to E741-11 developed by Committee E06.41, ASTM BOS Volume 04.11.
  • E772 Standard Terminology of Solar Energy Conversion
    Revised to E772-11 developed by Committee E44.09, ASTM BOS Volume 12.02.
  • E784 Standard Specification for Clamps, Utility, Laboratory, and Holders, Buret and Clamp
    Reapproved, available as E784-89(2011) developed by Committee E41.01, ASTM BOS Volume 14.04.
  • E902-05 Standard Practice for Checking the Operating Characteristics of X-Ray Photoelectron Spectrometers (Withdrawn 2011)
    Withdrawn with no replacement.
  • E995 Standard Guide for Background Subtraction Techniques in Auger Electron Spectroscopy and X-Ray Photoelectron Spectroscopy
    Revised to E995-11 developed by Committee E42.03, ASTM BOS Volume 03.06.
  • E998 Standard Test Method for Structural Performance of Glass in Windows, Curtain Walls, and Doors Under the Influence of Uniform Static Loads by Nondestructive Method
    Reapproved, available as E998-05(2011) developed by Committee E06.51, ASTM BOS Volume 04.11.
  • E1052 Standard Test Method to Assess the Activity of Microbicides against Viruses in Suspension
    Has been reinstated, with revision to E1052-11 developed by Committee E35.15, ASTM BOS Volume 11.05.
  • E1190 Standard Test Methods for Strength of Power-Actuated Fasteners Installed in Structural Members
    Revised to E1190-11 developed by Committee E06.13, ASTM BOS Volume 04.11.
  • E1336 Standard Test Method for Obtaining Colorimetric Data From a Visual Display Unit by Spectroradiometry
    Revised to E1336-11 developed by Committee E12.06, ASTM BOS Volume 06.01.
  • E1341 Standard Practice for Obtaining Spectroradiometric Data from Radiant Sources for Colorimetry
    Reapproved (with editorial change), available as E1341-06(2011)e1 developed by Committee E12.06, ASTM BOS Volume 06.01.
  • E1347 Standard Test Method for Color and Color-Difference Measurement by Tristimulus Colorimetry
    Reapproved, available as E1347-06(2011) developed by Committee E12.02, ASTM BOS Volume 06.01.
  • E1354 Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter
    Revised to E1354-11b developed by Committee E05.21, ASTM BOS Volume 04.07.
  • E1366 Standard Practice for Standardized Aquatic Microcosms: Fresh Water
    Revised to E1366-11 developed by Committee E47.01, ASTM BOS Volume 11.06.
  • E1368 Standard Practice for Visual Inspection of Asbestos Abatement Projects
    Revised to E1368-11 developed by Committee E06.24, ASTM BOS Volume 04.11.
  • E1514 Standard Specification for Structural Standing Seam Steel Roof Panel Systems
    Reapproved, available as E1514-98(2011) developed by Committee E06.57, ASTM BOS Volume 04.11.
  • E1619 Standard Test Method for Chronic Oral Toxicity Study in Rats
    Revised to E1619-11 developed by Committee E47.02, ASTM BOS Volume 11.06.
  • E1643 Standard Practice for Selection, Design, Installation, and Inspection of Water Vapor Retarders Used in Contact with Earth or Granular Fill Under Concrete Slabs
    Revised to E1643-11 developed by Committee E06.21, ASTM BOS Volume 04.11.
  • E1677 Standard Specification for Air Barrier (AB) Material or System for Low-Rise Framed Building Walls
    Revised to E1677-11 developed by Committee E06.41, ASTM BOS Volume 04.11.
  • E1732 Standard Terminology Relating to Forensic Science
    Revised to E1732-11b developed by Committee E30.92, ASTM BOS Volume 14.02.
  • E1745 Standard Specification for Plastic Water Vapor Retarders Used in Contact with Soil or Granular Fill under Concrete Slabs
    Revised to E1745-11 developed by Committee E06.21, ASTM BOS Volume 04.11.
  • E1827 Standard Test Methods for Determining Airtightness of Buildings Using an Orifice Blower Door
    Revised to E1827-11 developed by Committee E06.41, ASTM BOS Volume 04.11.
  • E1960 Standard Practice for Calculating International Friction Index of a Pavement Surface
    Reapproved, available as E1960-07(2011) developed by Committee E17.21, ASTM BOS Volume 04.03.
  • E1967 Standard Test Method for the Automated Determination of Refractive Index of Glass Samples Using the Oil Immersion Method and a Phase Contrast Microscope
    Revised to E1967-11 developed by Committee E30.01, ASTM BOS Volume 14.02.
  • E1998 Standard Guide for Assessing Depressurization-Induced Backdrafting and Spillage from Vented Combustion Appliances
    Revised to E1998-11 developed by Committee E06.41, ASTM BOS Volume 04.11.
  • E2029 Standard Test Method for Volumetric and Mass Flow Rate Measurement in a Duct Using Tracer Gas Dilution
    Revised to E2029-11 developed by Committee E06.41, ASTM BOS Volume 04.11.
  • E2102 Standard Test Method for Measurement of Mass Loss and Ignitability for Screening Purposes Using a Conical Radiant Heater
    Revised to E2102-11a developed by Committee E05.21, ASTM BOS Volume 04.07.
  • E2153 Standard Practice for Obtaining Bispectral Photometric Data for Evaluation of Fluorescent Color
    Reapproved, available as E2153-01(2011) developed by Committee E12.05, ASTM BOS Volume 06.01.
  • E2174 Standard Practice for On-Site Inspection of Installed Fire Stops
    Editorially changed, available as E2174-10ae1 developed by Committee E06.21, ASTM BOS Volume 04.12.
  • E2204 Standard Guide for Summarizing the Economic Impacts of Building-Related Projects
    Revised to E2204-11a developed by Committee E06.81, ASTM BOS Volume 04.12.
  • E2226 Standard Practice for Application of Hose Stream
    Revised to E2226-11 developed by Committee E05.11, ASTM BOS Volume 04.07.
  • E2251 Standard Specification for Liquid-in-Glass ASTM Thermometers with Low-Hazard Precision Liquids
    Revised to E2251-11 developed by Committee E20.05, ASTM BOS Volume 14.03.
  • E2357 Standard Test Method for Determining Air Leakage of Air Barrier Assemblies
    Revised to E2357-11 developed by Committee E06.41, ASTM BOS Volume 04.12.
  • E2369 Standard Specification for Continuity of Care Record (CCR)
    Editorially changed, available as E2369-05e2 developed by Committee E31.25, ASTM BOS Volume 14.01.
  • E2385 Standard Guide for Estimating Wildlife Exposure Using Measures of Habitat Quality
    Revised to E2385-11 developed by Committee E47.02, ASTM BOS Volume 11.06.
  • E2427 Standard Test Method for Acceptance by Performance Testing for Sieves
    Revised to E2427-11 developed by Committee E29.01, ASTM BOS Volume 14.02.
  • E2431 Standard Practice for Determining the Resistance of Single Glazed Annealed Architectural Flat Glass to Thermal Loadings
    Reapproved, available as E2431-06(2011) developed by Committee E06.51, ASTM BOS Volume 04.12.
  • E2489 Standard Practice for Statistical Analysis of One-Sample and Two-Sample Interlaboratory Proficiency Testing Programs
    Revised to E2489-11 developed by Committee E11.20, ASTM BOS Volume 14.02.
  • E2548 Standard Guide for Sampling Seized Drugs for Qualitative and Quantitative Analysis
    Revised to E2548-11 developed by Committee E30.01, ASTM BOS Volume 14.02.
  • E2579 Standard Practice for Specimen Preparation and Mounting of Wood Products to Assess Surface Burning Characteristics
    Revised to E2579-11 developed by Committee E05.22, ASTM BOS Volume 04.07.
  • E2583 Standard Test Method for Measuring Deflections with a Light Weight Deflectometer (LWD)
    Reapproved, available as E2583-07(2011) developed by Committee E17.41, ASTM BOS Volume 04.03.
  • E2751-11 Standard Practice for Design and Performance of Supported Glass Walkways
    New standard, now available. ASTM BOS Volume 04.12.
  • E2783 Standard Test Method for Assessment of Antimicrobial Activity for Water Miscible Compounds Using a Time-Kill Procedure
    Revised to E2783-11 developed by Committee E35.15, ASTM BOS Volume 11.05.
  • E2802-11 Standard Test Method for Evaluating Emergency Response Robot Capabilities: Mobility: Confined Area Obstacles: Hurdles
    New standard, now available. ASTM BOS Volume 15.08.
  • E2803-11 Standard Test Method for Evaluating Emergency Response Robot Capabilities: Mobility: Confined Area Obstacles: Inclined Planes
    New standard, now available. ASTM BOS Volume 15.08.
  • E2817-11 Standard Test Method for Test Fueling Masonry Heaters
    New standard, now available. ASTM BOS Volume 04.12.
  • E2819-11 Standard Practice for Single- and Multi-Level Continuous Sampling of a Stream of Product by Attributes Indexed by AQL
    New standard, now available. ASTM BOS Volume 14.02.
  • F99 Standard Guide for Writing a Specification for Flexible Barrier Rollstock Materials
    Reapproved, available as F99-07(2011) developed by Committee F02.50, ASTM BOS Volume 15.10.
  • F625/F625M Standard Practice for Classifying Water Bodies for Spill Control Systems
    Reapproved (with editorial change), available as F625/F625M-94(2011)e1 developed by Committee F20.11, ASTM BOS Volume 11.05.
  • F625/F625M Standard Practice for Classifying Water Bodies for Spill Control Systems
    Reapproved (with editorial change), available as F625/F625M-94(2011)e2 developed by Committee F20.11, ASTM BOS Volume 11.05.
  • F876 Standard Specification for Crosslinked Polyethylene (PEX) Tubing
    Editorially changed, available as F876-10e1 developed by Committee F17.26, ASTM BOS Volume 08.04.
  • F1147 Standard Test Method for Tension Testing of Calcium Phosphate and Metallic Coatings
    Reapproved, available as F1147-05(2011) developed by Committee F04.15, ASTM BOS Volume 13.01.
  • F1178 Standard Specification for Performance of Enameling System, Baking, Metal Joiner Work and Furniture
    Revised to F1178-11 developed by Committee F25.01, ASTM BOS Volume 01.07.
  • F1190 Standard Guide for Neutron Irradiation of Unbiased Electronic Components
    Revised to F1190-11 developed by Committee F01.11, ASTM BOS Volume 10.04.
  • F1192 Standard Guide for the Measurement of Single Event Phenomena (SEP) Induced by Heavy Ion Irradiation of Semiconductor Devices
    Revised to F1192-11 developed by Committee F01.11, ASTM BOS Volume 10.04.
  • F1249 Standard Test Method for Water Vapor Transmission Rate Through Plastic Film and Sheeting Using a Modulated Infrared Sensor
    Reapproved, available as F1249-06(2011) developed by Committee F02.10, ASTM BOS Volume 15.10.
  • F1335-04 Standard Specification for Pressure-Rated Composite Pipe and Fittings for Elevated Temperature Service (Withdrawn 2011)
    Withdrawn with no replacement.
  • F1370 Standard Specification for Pressure-Reducing Valves for Water Systems, Shipboard
    Reapproved, available as F1370-92(2011) developed by Committee F25.11, ASTM BOS Volume 01.07.
  • F1455 Standard Guide for Selection of Structural Details for Ship Construction
    Reapproved, available as F1455-92(2011) developed by Committee F25.01, ASTM BOS Volume 01.07.
  • F1467 Standard Guide for Use of an X-Ray Tester (?10 keV Photons) in Ionizing Radiation Effects Testing of Semiconductor Devices and Microcircuits
    Revised to F1467-11 developed by Committee F01.11, ASTM BOS Volume 10.04.
  • F1487 Standard Consumer Safety Performance Specification for Playground Equipment for Public Use
    Revised to F1487-11 developed by Committee F15.29, ASTM BOS Volume 15.11.
  • F1541 Standard Specification and Test Methods for External Skeletal Fixation Devices
    Reapproved, available as F1541-02(2011) developed by Committee F04.21, ASTM BOS Volume 13.01.
  • F1554 Standard Specification for Anchor Bolts, Steel, 36, 55, and 105-ksi Yield Strength
    Editorially changed, available as F1554-07ae1 developed by Committee F16.02, ASTM BOS Volume 01.08.
  • F1563 Standard Specification for Tools to Squeeze-off Polyethylene (PE) Gas Pipe or Tubing
    Reapproved, available as F1563-01(2011) developed by Committee F17.60, ASTM BOS Volume 08.04.
  • F1612-95(2005) Standard Practice for Cyclic Fatigue Testing of Metallic Stemmed Hip Arthroplasty Femoral Components with Torsion (Withdrawn 2011)
    Withdrawn with no replacement.
  • F1667 Standard Specification for Driven Fasteners: Nails, Spikes, and Staples
    Revised to F1667-11a developed by Committee F16.05, ASTM BOS Volume 01.08.
  • F1980 Standard Guide for Accelerated Aging of Sterile Barrier Systems for Medical Devices
    Reapproved, available as F1980-07(2011) developed by Committee F02.50, ASTM BOS Volume 15.10.
  • F1985 Standard Specification for Pneumatic-Operated, Globe-Style, Control Valves
    Reapproved, available as F1985-99(2011) developed by Committee F25.11, ASTM BOS Volume 01.07.
  • F1986 Standard Specification for Multilayer Pipe Type 2, Compression Fittings, and Compression Joints for Hot and Cold Drinking-Water Systems
    Reapproved, available as F1986-01(2011) developed by Committee F17.11, ASTM BOS Volume 08.04.
  • F1987 Standard Specification for Multilayer Pipe Type 2, Compression Fittings, and Compression Joints for Hydronic Heating Systems
    Reapproved, available as F1987-01(2011) developed by Committee F17.11, ASTM BOS Volume 08.04.
  • F2088 Standard Consumer Safety Specification for Infant Swings
    Revised to F2088-11b developed by Committee F15.21, ASTM BOS Volume 15.11.
  • F2180 Standard Specification for Metallic Implantable Strands and Cables
    Reapproved, available as F2180-02(2011) developed by Committee F04.21, ASTM BOS Volume 13.01.
  • F2213 Standard Test Method for Measurement of Magnetically Induced Torque on Medical Devices in the Magnetic Resonance Environment
    Reapproved, available as F2213-06(2011) developed by Committee F04.15, ASTM BOS Volume 13.01.
  • F2280 Standard Specification for “Twist Off” Type Tension Control Structural Bolt/Nut/Washer Assemblies, Steel, Heat Treated, 150 ksi Minimum Tensile Strength
    Revised to F2280-11a developed by Committee F16.02, ASTM BOS Volume 01.08.
  • F2417 Standard Specification for Fire Safety for Candles
    Revised to F2417-11 developed by Committee F15.45, ASTM BOS Volume 15.11.
  • F2465/F2465M Standard Guide for Oil Spill Dispersant Application Equipment: Single-point Spray Systems
    Reapproved (with editorial change), available as F2465/F2465M-05(2011)e1 developed by Committee F20.13, ASTM BOS Volume 11.05.
  • F2640 Standard Consumer Safety Specification for Booster Seats
    Revised to F2640-11a developed by Committee F15.16, ASTM BOS Volume 15.11.
  • F2923-11 Standard Specification for Consumer Product Safety for Children's Jewelry
    New standard, now available. ASTM BOS Volume 15.11.
  • F2925-11 Standard Specification for Tenderness Marketing Claims Associated with Meat Cuts Derived from Beef
    New standard, now available. ASTM BOS Volume 15.12.

Published in international.