BRITISH STANDARDS

You can now purchase PDFs of British Standards from Standards New Zealand – please email enquiries@standards.co.nz or call 0800 782 632 during business hours to order PDFs. British Standard publications in hardcopy format are also available for purchase from our web site www.standards.co.nz by entering the Standard number and selecting the BSI button in the search panel.

The publications listed below are new and revised British Standards that were made available last month. An existing BSI publication bearing a number identical to one announced below is automatically withdrawn unless stated otherwise. In all other cases of supersession, details are given and a corresponding entry appears in the 'British Standards withdrawn' section.

  • BS 6180:2011 Barriers in and about buildings. Code of practice
    Supersedes BS 6180:1999
  • BS 7371-8:2011 Coatings on metal fasteners. Specification for sherardized coatings
    Supersedes BS 7371-8:1998
  • BS 8532:2011 Terminal units for high flow anaesthetic gas scavenging systems. Specification for robes and type-specific connection points
  • BS 8562:2011 Gas cylinders. In situ, non-destructive examination and testing of refillable seamless steel tubes of water capacity between 150 L and 3000 L, used for compressed gases. Specification
  • BS 8887-240:2011 Design for manufacture, assembly, disassembly and end-of-life processing (MADE). Reconditioning
  • BS 8909:2011 Specification for a sustainability management system for film
  • BS 10175:2011 Investigation of potentially contaminated sites. Code of practice
    Supersedes BS 10175:2001

BS EN PUBLICATIONS

The following are British Standard implementations of the English language versions of European Standards (ENs). The date referenced in the identifier is the date of the European Standard. You can now purchase PDFs of British Standards from Standards New Zealand – please email enquiries@standards.co.nz or call 0800 782 632 during business hours to order PDFs.

  • BS EN ISO 544:2011 Welding consumables. Technical delivery conditions for filler materials and fluxes. Type of product, dimensions, tolerances and markings
    Supersedes BS EN ISO 544:2003
  • BS EN 624:2011 Specification for dedicated LPG appliances. Room sealed LPG space heating equipment for installation in vehicles and boats
    Supersedes BS EN 624:2000
  • BS EN 1520:2011 Prefabricated reinforced components of lightweight aggregate concrete with open structure with structural or non-structural reinforcement
    Supersedes BS EN 1520:2002
  • BS EN 1949:2011 Specification for the installation of LPG systems for habitation purposes in leisure accommodation vehicles and accommodation purposes in other vehicles
    Supersedes BS EN 1949:2002
  • BS EN ISO 2106:2011 Anodizing of aluminium and its alloys. Determination of mass per unit area (surface density) of anodic oxidation coatings. Gravimetric method
    Supersedes BS EN 12373-2:1999
  • BS EN 2240-051:2011 Aerospace series. Lamps, incandescent. Lamp, code 1163. Product standard
  • BS EN 2240-052:2011 Aerospace series. Lamps, incandescent. Lamp, code 1222. Product standard
  • BS EN 2240-053:2011 Aerospace series. Lamps, incandescent. Lamp, code 1308. Product standard
  • BS EN 2240-054:2011 Aerospace series. Lamps, incandescent. Lamp, code 1317. Product standard
  • BS EN 2240-055:2011 Aerospace series. Lamps, incandescent. Lamp, code 1495. Product standard
  • BS EN 2240-056:2011 Aerospace series. Lamps, incandescent. Lamp, code 1506. Product standard
  • BS EN 2240-057:2011 Aerospace series. Lamps, incandescent. Lamp, code 1512. Product standard
  • BS EN 2240-058:2011 Aerospace series. Lamps, incandescent. Lamp, code 1524. Product standard
  • BS EN 2240-059:2011 Aerospace series. Lamps, incandescent. Lamp, code 1591. Product standard
  • BS EN 2240-060:2011 Aerospace series. Lamps, incandescent. Lamp, code 1619. Product standard
  • BS EN ISO 2811-1:2011 Paints and varnishes. Determination of density. Pyknometer method
    Supersedes the dual numbered standard BS EN ISO 2811-1:2001, BS 3900-A19:1998
  • BS EN ISO 2811-2:2011 Paints and varnishes. Determination of density. Immersed body (plummet) method
    Supersedes the dual numbered standard BS EN ISO 2811-2:2001, BS 3900-A20:1998
  • BS EN ISO 2811-3:2011 Paints and varnishes. Determination of density. Oscillation method
    Supersedes the dual numbered standard BS EN ISO 2811-3:2001, BS 3900-A21:1998
  • BS EN ISO 2811-4:2011 Paints and varnishes. Determination of density. Pressure cup method
    Supersedes the dual numbered standard BS EN ISO 2811-4:2001, BS 3900-A22:1998
  • BS EN 2826:2011 Aerospace series. Burning behaviour of non-metallic materials under the influence of radiating heat and flames. Determination of gas components in the smoke
  • BS EN ISO 3107:2011 Dentistry. Zinc oxide/eugenol cements and zinc oxide/non-eugenol cements
    Supersedes BS EN ISO 3107:2004
  • BS EN ISO 3381:2011 Railway applications. Acoustics. Measurement of noise inside railbound vehicles
    Supersedes BS EN ISO 3381:2005
  • BS EN ISO 4014:2011 Hexagon head bolts. Product grades A and B
    Supersedes BS EN ISO 4014:2001
  • BS EN ISO 4016:2011 Hexagon head bolts. Product grade C
    Supersedes BS EN ISO 4016:2001
  • BS EN ISO 4136:2011 Destructive tests on welds in metallic materials. Transverse tensile test
    Supersedes BS EN 895:1995
  • BS EN 4660-001:2011 Aerospace series. Modular and open avionics architectures. Architecture
  • BS EN 4660-002:2011 Aerospace series. Modular and open avionics architectures. Common functional modules
  • BS EN 4660-003:2011 Aerospace series. Modular and open avionics architectures. Communications/Network
  • BS EN 4660-004:2011 Aerospace series. Modular and open avionics architectures. Packaging
  • BS EN 4673-003:2010 Aerospace series. Inserts, UNJ threads, self-locking, with self-broaching keys. Technical specification
  • BS EN ISO 5178:2011 Destructive tests on welds in metallic materials. Longitudinal tensile test on weld metal in fusion welded joints
    Supersedes BS EN 876:1995
  • BS EN ISO 5667-23:2011 Water quality. Sampling. Guidance on passive sampling in surface waters
  • BS EN ISO 8029:2010 Plastics hose. General-purpose collapsible water hose, textile-reinforced. Specification
    Supersedes BS EN 28029:1993
  • BS EN ISO 8765:2011 Hexagon head bolts with metric fine pitch thread. Product grades A and B
    Supersedes BS EN ISO 8765:2001
  • BS EN ISO 8994:2011 Anodizing of aluminium and its alloys. Rating system for the evaluation of pitting corrosion. Grid method
    Supersedes BS EN 12373-19:2001
  • BS EN ISO 9016:2011 Destructive tests on welds in metallic materials. Impact tests. Test specimen location, notch orientation and examination
    Supersedes BS EN 875:1995
  • BS EN ISO 10350-2:2011 Plastics. Acquisition and presentation of comparable single-point data. Long-fibre reinforced plastics
    Supersedes BS EN ISO 10350-2:2001
  • BS EN 10351:2011 Chemical analysis of ferrous materials. Inductively coupled plasma optical emission spectrometric analysis of unalloyed and low alloyed steels. Determination of Mn, P, Cu, Ni, Cr, Mo, V, Co, Al (total) and Sn [Routine method]
  • BS EN ISO 10748:2011 Footwear. Test method for slide fasteners. Slider locking strength
  • BS EN ISO 11073-10415:2011 Health informatics. Personal health device communication. Device specialization. Weighing scale
  • BS EN ISO 11114-3:2010 Gas cylinders. Compatibility of cylinder and valve materials with gas contents. Autogenous ignition test for non-metallic materials in oxygen atmosphere
    Supersedes BS EN ISO 11114-3:1998
  • BS EN 13089:2011 Mountaineering equipment. Ice-tools. Safety requirements and test methods
    Supersedes BS EN 13089:1999
  • BS EN 13598-1:2010 Plastics piping systems for non-pressure underground drainage and sewerage. Unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE). Specifications for ancillary fittings including shallow inspection chambers
    Supersedes BS EN 13598-1:2003 which is withdrawn. Supersedes BS 7158:2001 which remains current. Partially supersedes BS 4660:2000
  • BS EN 13710:2011 European Ordering Rules. Ordering of characters from Latin, Greek, Cyrillic, Georgian and Armenian scripts
    Supersedes DD ENV 13710:2001
  • BS EN 13795:2011 Surgical drapes, gowns and clean air suits, used as medical devices for patients, clinical staff and equipment. General requirements for manufacturers, processors and products, test methods, performance requirements and performance levels
    Supersedes BS EN 13795-1:2002+A1:2009, BS EN 13795-2:2004+A1:2009 and BS EN 13795-3:2006+A1:2009
  • BS EN 14033-1:2011 Railway applications. Track. Rail-bound construction and maintenance machines. Technical requirements for running
    Supersedes BS EN 14033-1:2008
  • BS EN 14127:2011 Non-destructive testing. Ultrasonic thickness measurement
    Supersedes BS EN 14127:2004
  • BS EN 14961-5:2011 Solid biofuels. Fuel specifications and classes. Firewood for non-industrial use
  • BS EN 15234-1:2011 Solid biofuels. Fuel quality assurance. General requirements
    Supersedes DD CEN/TS 15234:2006
  • BS EN 15316-4-8:2011 Heating systems in buildings. Method for calculation of system energy requirements and system efficiencies. Space heating generation systems, air heating and overhead radiant heating systems
  • BS EN 15357:2011 Solid recovered fuels. Terminology, definitions and descriptions
    Supersedes DD CEN/TS 15357:2006
  • BS EN 15358:2011 Solid recovered fuels. Quality management systems. Particular requirements for their application to the production of solid recovered fuels
    Supersedes DD CEN/TS 15358:2006
  • BS EN 15400:2011 Solid recovered fuels. Determination of calorific value
    Supersedes DD CEN/TS 15400:2006
  • BS EN 15402:2011 Solid recovered fuels. Determination of the content of volatile matter
    Supersedes DD CEN/TS 15402:2006
  • BS EN 15403:2011 Solid recovered fuels. Determination of ash content
    Supersedes DD CEN/TS 15403:2006
  • BS EN 15407:2011 Solid recovered fuels. Methods for the determination of carbon (C), hydrogen (H) and nitrogen (N) content
    Supersedes DD CEN/TS 15407:2006
  • BS EN 15408:2011 Solid recovered fuels. Methods for the determination of sulphur (S), chlorine (Cl), fluorine (F) and bromine (Br) content
    Supersedes DD CEN/TS 15408:2006
  • BS EN 15414-3:2011 Solid recovered fuels. Determination of moisture content using the oven dry method. Moisture in general analysis sample
    Supersedes DD CEN/TS 15414-3:2006
  • BS EN 15442:2011 Solid recovered fuels. Methods for sampling
    Supersedes DD CEN/TS 15442:2006
  • BS EN 15443:2011 Solid recovered fuels. Methods for the preparation of the laboratory sample
    Supersedes DD CEN/TS 15443:2006
  • BS EN 15518-1:2011 Winter maintenance equipment. Road weather information systems. Global definitions and components
  • BS EN 15518-2:2011 Winter maintenance equipment. Road weather information systems. Road weather. Recommended observation and forecast
  • BS EN 15518-3:2011 Winter maintenance equipment. Road weather information systems. Requirements on measured values of stationary equipments
  • BS EN 15643-2:2011 Sustainability of construction works. Assessment of buildings. Framework for the assessment of environmental performance
  • BS EN 15879-1:2011 Testing and rating of direct exchange ground coupled heat pumps with electrically driven compressors for space heating and/or cooling. Direct exchange-to-water heat pumps
  • BS EN 15973:2011 Rubber- or plastic-coated fabrics. Upholstery fabrics. Resistance to soiling
  • BS EN 15975-1:2011 Security of drinking water supply. Guidelines for risk and crisis management. Crisis management
  • BS EN 15977:2011 Rubber or plastic coated fabrics. Mechanical properties. Determination of the elongation under load and the residual deformation
  • BS EN 15986:2011 Symbol for use in the labelling of medical devices. Requirements for labelling of medical devices containing phthalates
  • BS EN ISO/IEC 17021:2011 Conformity assessment. Requirements for bodies providing audit and certification of management systems
    Supersedes BS EN ISO/IEC 17021:2006 which remains current
  • BS EN ISO 17234-2:2011 Leather. Chemical tests for the determination of certain azo colorants in dyed leathers. Determination of 4-aminoazobenzene
  • BS EN ISO 17637:2011 Non-destructive testing of welds. Visual testing of fusion-welded joints
    Supersedes BS EN 970:1997
  • BS EN 50289-4-17:2011 Communication cables. Specifications for test methods. Test methods for UV resistance evaluation of the sheath of electrical and optical fibre cable
  • BS EN 60770-2:2010 Transmitters for use in industrial-process control systems. Methods for inspection and routine testing
    Supersedes BS EN 60770-2:2003 which remains current
  • BS EN 60793-1-30:2011 Optical fibres. Measurement methods and test procedures. Fibre proof test
    Supersedes BS EN 60793-1-30:2002
  • BS EN 60793-2-40:2011 Optical fibres. Product specifications. Sectional specification for category A4 multimode fibres
    Supersedes BS EN 60793-2-40:2006
  • BS EN 61439-5:2011 Low-voltage switchgear and controlgear assemblies. Assemblies for power distribution in public networks
    Supersedes BS EN 60439-5:2006 which remains current
  • BS EN 61558-2-9:2011 Safety of transformers, reactors, power supply units and combinations thereof. Particular requirements and tests for transformers and power supply units for class III handlamps for tungsten filament lamps
    Supersedes BS EN 61558-2-9:2003 which remains current
  • BS EN 61558-2-20:2011 Safety of transformers, reactors, power supply units and combinations thereof. Particular requirements and tests for small reactors
    Supersedes BS EN 61558-2-20:2001 which remains current
  • BS EN 61850-7-3:2011 Communication networks and systems for power utility automation. Basic communication structure. Common data classes
    Supersedes BS EN 61850-7-3:2003
  • BS EN 61853-1:2011 Photovoltaic (PV) module performance testing and energy rating. Irradiance and temperature performance measurements and power rating
  • BS EN 62341-6-1:2011 Organic light emitting diode (OLED) displays. Measuring methods of optical and electro-optical parameters
  • BS EN 62464-2:2011 Magnetic resonance equipment for medical imaging. Classification criteria for pulse sequences
  • BS EN 62496-3:2011 Optical circuit boards. Performance standards. General and guidance
  • BS EN 62496-4:2011 Optical circuit boards. Interface standards. General and guidance
  • BS EN 62524:2011 Multimedia systems and equipment. Multimedia e-publishing and e-books. Reader's format for e-publishing
  • BS EN 62562:2011 Cavity resonator method to measure the complex permittivity of low-loss dielectric plates
    Supersedes DD IEC/PAS 62562:2008

BS ENs implemented by amendment

  • BS EN ISO 8623:2010 Tall-oil fatty acids for paints and varnishes. Specifications and test methods
    Implementation of European Standard EN ISO 8623 by amendment to BS 6782-15:1997

BS Implementations

BS Implementations comprise the ISO or IEC text without any national deviation and with front and back cover indicating the UK committee responsible. No other information will normally be added. The date referenced in the identifier is the date of the international standard.

  • BS ISO 15:2011 Rolling bearings. Radial bearings. Boundary dimensions, general plan
    Supersedes BS ISO 15:1998
  • BS ISO 1652:2011 Rubber latex. Determination of apparent viscosity by the Brookfield test method
    Supersedes BS ISO 1652:2004
  • BS ISO 3888-2:2011 Passenger cars. Test track for a severe lane-change manoeuvre. Obstacle avoidance
    Supersedes BS ISO 3888-2:2002
  • BS ISO 4660:2011 Rubber, raw natural. Colour index test
    Supersedes BS ISO 4660:1999
  • BS ISO 7301:2011 Rice. Specification
  • BS ISO 7637-2:2011 Road vehicles. Electrical disturbances from conduction and coupling. Electrical transient conduction along supply lines only
  • BS ISO 8516:2011 Textile glass. Textured yarns. Basis for a specification
  • BS ISO 9564-1:2011 Financial services. Personal identification number (PIN) management and security. Basic principles and requirements for PINs in card based systems
  • BS ISO 9698:2010 Water quality. Determination of tritium activity concentration. Liquid scintillation counting method
  • BS ISO/IEC 9797-1:2011 Information technology. Security techniques. Message authentication codes (MACs). Mechanisms using a block cipher
  • BS ISO 12176-3:2011 Plastics pipes and fittings. Equipment for fusion jointing polyethylene systems. Operator's badge
  • BS ISO 13091-1:2001 Mechanical vibrations. Vibrotactile perception thresholds for the assessment of nerve dysfunction. Methods of measurement at the fingertips
  • BS ISO 14792:2011 Road vehicles. Heavy commercial vehicles and buses. Steady-state circular tests
    Supersedes BS ISO 14792:2003
  • BS ISO/IEC 15026-2:2011 Systems and software engineering. Systems and software assurance. Assurance case
  • BS ISO 15765-4:2011 Road vehicles. Diagnostic communication over controller area network (DoCAN). Requirements for emissions-related systems
  • BS ISO 16844-2:2011 Road vehicles. Tachograph systems. Electrical interface with recording unit
  • BS ISO 17853:2011 Wear of implant materials. Polymer and metal wear particles. Isolation and characterization
    Supersedes BS ISO 17853:2010
  • BS ISO 18192-1:2011 Implants for surgery. Wear of total intervertebral spinal disc prostheses. Loading and displacement parameters for wear testing and corresponding environmental conditions for test
    Supersedes BS ISO 18192-1:2008
  • BS ISO 18292:2011 Energy performance of fenestration systems for residential buildings. Calculation procedure
  • BS ISO/IEC 19784-4:2011 Information technology. Biometric application programming interface. Biometric sensor function provider interface
  • BS ISO/IEC 19795-5:2011 Information technology. Biometric performance testing and reporting. Access control scenario and grading scheme
  • BS ISO 21667:2010 Health informatics. Health indicators conceptual framework
    Supersedes DD ISO/TS 21667:2004
  • BS ISO 22915-14:2010 Industrial trucks. Verification of stability. Rough-terrain variable-reach trucks
    Supersedes BS ISO 8379:1998 which remains current
  • BS ISO 23873:2010 Hard coal. Method for the measurement of the swelling of hard coal using a dilatometer
  • BS ISO/IEC 25010:2011 Systems and software engineering. Systems and software quality requirements and evaluation (SQuaRE). System and software quality models
    Supersedes BS ISO/IEC 9126-1:2001
  • BS ISO/IEC 25040:2011 Systems and software engineering. Systems and software quality requirements and evaluation (SQuaRE). Evaluation process
    Supersedes BS ISO/IEC 14598-1:1999
  • BS ISO/IEC 27031:2011 Information technology. Security techniques. Guidelines for information and communication technology readiness for business continuity
    Supersedes BS 25777:2008
  • BS ISO 27470:2011 Aircraft ground equipment. Upper deck catering vehicle. Functional requirements
  • BS ISO/IEC 29143:2011 Information technology. Automatic identification and data capture techniques. Air interface specification for mobile RFID interrogators
  • BS ISO 29262:2011 Production equipment for microsystems. Interface between end effector and handling system

PUBLISHED DOCUMENTS

  • PD CISPR/TR 16-3:2010 Specification for radio disturbance and immunity measuring apparatus and methods. CISPR technical reports
    Supersedes PD CISPR/TR 16-3:2003
  • PD CEN/TR 15642:2011 Unified tests procedures for the tests of EN 3-7:2004+A1:2007
    Supersedes PD CEN/TR 15642:2008
  • PD CEN/TR 16092:2011 Electronic fee collection. Requirements for prepayment systems
  • PD CEN/TR 16142:2011 Concrete. A study of the characteristic leaching behaviour of hardened concrete for use in the natural environment
  • PD CEN ISO/TR 16178:2010 Footwear. Critical substances potentially present in footwear and footwear components
  • PD CLC/TR 50436-3:2010 Alcohol interlocks. Test methods and performance requirements. Guidance for decision makers, purchasers and users
  • PD IEC/TR 62131-1:2011 Environmental conditions. Vibration and shock of electrotechnical equipment. Process for validation of dynamic data
  • PD IEC/TR 62131-2:2011 Environmental conditions. Vibration and shock of electrotechnical equipment. Equipment transported in fixed wing jet aircraft
  • PD IEC/TR 62131-3:2011 Environmental conditions. Vibration and shock of electrotechnical equipment. Equipment transported in rail vehicles
  • PD IEC/TR 62131-4:2011 Environmental conditions. Vibration and shock of electrotechnical equipment. Equipment transported in road vehicles
  • PD IEC/TR 62271-301:2009 High-voltage switchgear and controlgear. Dimensional standardisation of high-voltage terminals
  • PD IEC/TR 62343-6-5:2011 Dynamic modules. Investigation of operating mechanical shock and vibration tests for dynamic modules

Publicly available specifications

Publicly Available Specifications (formerly Product Assessment Specifications) are issued to provide an interim document where there is a market need but where a full Standard has yet to be published.

  • PAS 124:2011 Defining, implementing and managing website policies and standards. Code of practice
    Supersedes PAS 124:2008
  • PAS 141:2011 Reuse of used and waste electrical and electronic equipment (UEEE and WEEE). Process management. Specification
  • PAS 1010:2011 Guidance on the management of psychosocial risks in the workplace

Corrigenda to British Standards and updated British Standards

Most British amendments are not issued separately. Those that make significant changes to a standard are incorporated into the standard which is re-issued as a new edition. All amendments to date of despatch are included within any main publication when ordered for the first time. The following amended Standards and corrigenda to British Standards were made available last month.

  • BS 8509:2008+A1:2011 Children's beds for domestic use. Safety requirements and test methods
    AMENDMENT 1
  • BS EN 228:2008 Automotive fuels. Unleaded petrol. Requirements and test methods
    CORRIGENDUM 2
  • BS EN 378-1:2008+A1:2010 Refrigerating systems and heat pumps. Safety and environmental requirements. Basic requirements, definitions, classification and selection criteria
    AMENDMENT 1
  • BS EN 617:2001+A1:2010 Continuous handling equipment and systems. Safety and EMC requirements for the equipment for the storage of bulk materials in silos, bunkers, bins and hoppers
    AMENDMENT 1
  • BS EN ISO 3691-5:2009 Industrial trucks. Safety requirements and verification. Pedestrian-propelled trucks
    CORRIGENDUM 1
  • BS EN ISO 7214:2007 Cellular plastics. Polyethylene. Methods of test
    CORRIGENDUM 1
  • BS EN ISO 8623:2010 Tall-oil fatty acids for paints and varnishes. Specifications and test methods
    CORRIGENDUM 1
  • BS EN 13032-2:2004 Light and lighting. Measurement and presentation of photometric data of lamps and luminaires. Presentation of data for indoor and outdoor work places
    CORRIGENDUM 2
  • BS EN 13341:2005+A1:2011 Static thermoplastic tanks for above ground storage of domestic heating oils, kerosene and diesel fuels. Blow moulded and rotationally moulded polyethylene tanks and rotationally moulded tanks made of anionically polymerized polyamide 6. Requirements and test methods
    AMENDMENT 1
  • PD CEN/TR 15990:2010 Data sheets. Footwear tests materials and test adhesives
    CORRIGENDUM 1
  • BS EN 50173-2:2007+A1:2010 Information technology. Generic cabling systems. Office premises
    AMENDMENT 1
  • BS EN 50173-5:2007+A1:2010 Information technology. Generic cabling systems. Data centres
    AMENDMENT 1
  • BS EN 50342-5:2010 Lead-acid starter batteries. Properties of battery housings and handles
    CORRIGENDUM 1
  • BS EN 60335-2-76:2005+A12:2010 Household and similar electrical appliances. Safety. Particular requirements for electric fence energizers
    CORRIGENDUM 2
  • BS EN 60601-2-33:2010 Medical electrical equipment. Particular requirements for the basic safety and essential performance of magnetic resonance equipment for medical diagnosis
    CORRIGENDUM 1
  • BS EN 60825-2:2004+A2:2010 Safety of laser products. Safety of optical fibre communication systems (OFCS)
    AMENDMENT 2
  • BS EN 60893-3-5:2004+A1:2009 Insulating materials. Industrial rigid laminated sheets based on thermosetting resins for electrical purposes. Specifications for individual materials. Requirements for rigid laminated sheets based on polyester resins
    AMENDMENT 1
  • BS EN 60893-3-6:2004+A1:2009 Insulating materials. Industrial rigid laminated sheets based on thermosetting resins for electrical purposes. Specifications for individual materials. Requirements for rigid laminated sheets based on silicone resins
    AMENDMENT 1
  • BS EN 60893-3-7:2004+A1:2009 Insulating materials. Industrial rigid laminated sheets based on thermosetting resins for electrical purposes. Specifications for individual materials. Requirements for rigid laminated sheets based on polyimide resins
    AMENDMENT 1
  • BS EN 61190-1-3:2007+A1:2010 Attachment materials for electronic assembly. Requirements for electronic grade solder alloys and fluxed and non-fluxed solid solders for electronic soldering applications
    AMENDMENT 1
  • BS EN 61243-1:2005+A1:2010 Live working. Voltage detectors. Capacitive type to be used for voltages exceeding 1 kV A.C.
    AMENDMENT 1
  • BS EN 61326-1:2006 Electrical equipment for measurement, control and laboratory use. EMC requirements. General requirements
    CORRIGENDUM 2
  • BS EN 61347-2-8:2001+A1:2006 Lamp controlgear. Particular requirements for ballasts for fluorescent lamps
    CORRIGENDUM 2
  • BS EN 61803:1999+A1:2010 Determination of power losses in high-voltage direct current (HVDC) converter stations with line-commutated converters
    AMENDMENT 1
  • BS ISO 1268-4:2005+A1:2010 Fibre-reinforced plastics. Methods of producing test plates. Moulding of prepregs
    AMENDMENT 1
  • BS ISO 4603:1993+A1:2010 Textile glass. Woven fabrics. Determination of thickness
    AMENDMENT 1
  • BS ISO 10961:2010 Gas cylinders. Cylinder bundles. Design, manufacture, testing and inspection
    CORRIGENDUM 1
  • BS ISO/IEC 14651:2007+A1:2009 Information technology. International string ordering and comparison. Method for comparing character strings and description of the common template tailorable ordering
    AMENDMENT 1
  • PD ISO/TR 18394:2006 Surface chemical analysis. Auger electron spectroscopy. Derivation of chemical information
    CORRIGENDUM 1
  • DD CLC/TS 61836:2009 Solar photovoltaic energy systems. Terms, definitions and symbols
    CORRIGENDUM 1
  • BS 2S 201:2004+A1:2011 Carbon steel wire rod, patented cold drawn carbon steel wire and springs. High duty unground wire. Specification
    AMENDMENT 1
  • BS 2S 202:2004+A1:2011 Carbon steel wire rod, patented cold drawn carbon steel wire and springs. High duty ground wire. Specification
    AMENDMENT 1
  • BS 2S 203:2004 Carbon steel wire rod, wire and springs. High duty unground wire. Hardened and tempered. Specification
    CORRIGENDUM 1
  • BS 2S 204:2004 Chromium-vanadium steel wire rod, wire and springs. High duty ground wire. Hardened and tempered. Specification
    CORRIGENDUM 1
  • BS 2S 205:2004 Austenitic chromium-nickel steel wire rod, wire and springs. Specification
    CORRIGENDUM 1
  • BS SP 41-46:1951+A4:2011 Specifications for Tab washers for B.A. and B.S.W. hexagons for aircraft
    AMENDMENT 4
  • BS SP 107-112:1954+A4:2011 Specifications for Tab washers for unified hexagons for aircraft
    AMENDMENT 4
  • BS SP 122 to 125:1958+A2:2011 Washers for unified hexagons for aircraft (primarily for packing purposes)
    CORRIGENDUM 1
  • BS SP 126 & 127:1959+A3:2011 Washers for unified hexagons for aircraft (primarily for facing purposes)
    CORRIGENDUM 1

British Standards withdrawn

  • BS 25777:2008 Information and communications technology continuity management. Code of practice
    Superseded by BS ISO/IEC 27031:2011
  • BS EN 746-2:1997 Industrial thermoprocessing equipment. Safety requirements for combustion and fuel handling systems
    Superseded by BS EN 746-2:2010
  • BS EN 875:1995 Destructive tests on welds in metallic materials. Impact tests. Test specimen location, notch orientation and examination
    Superseded by BS EN ISO 9016:2011
  • BS EN 876:1995 Destructive tests on welds in metallic materials. Longitudinal tensile test on weld metal in fusion welded joints
    Superseded by BS EN ISO 5178:2011
  • BS EN 895:1995 Destructive tests on welds in metallic materials. Transverse tensile test
    Superseded by BS EN ISO 4136:2011
  • BS EN 970:1997 Non-destructive examination of fusion welds. Visual examination
    Superseded by BS EN ISO 17637:2011
  • BS EN 12373-2:1999 Aluminium and aluminium alloys. Anodizing. Determination of mass per unit area (surface density) of anodic oxidation coatings. Gravimetric method
    Superseded by BS EN ISO 2106:2011
  • BS EN 12373-19:2001 Aluminium and aluminium alloys. Anodizing. Rating system for the evaluation of pitting corrosion. Grid method
    Superseded by BS EN ISO 8994:2011
  • DD ENV 13710:2001 European Ordering Rules. Ordering of characters from the Latin, Greek and Cyrillic scripts
    Superseded by BS EN 13710:2011
  • BS EN 13795-1:2002+A1:2009 Surgical drapes, gowns and clean air suits, used as medical devices, for patients, clinical staff and equipment. General requirements for manufacturers, processors and products
    Superseded by BS EN 13795:2011
  • BS EN 13795-2:2004+A1:2009 Surgical drapes, gowns and clean air suits, used as medical devices for patients, clinical staff and equipment. Test methods
    Superseded by BS EN 13795:2011
  • BS EN 13795-3:2006+A1:2009 Surgical drapes, gowns and clean air suits, used as medical devices for patients, clinical staff and equipment. Performance requirements and performance levels
    Superseded by BS EN 13795:2011
  • DD CEN/TS 15234:2006 Solid biofuels. Fuel quality assurance
    Superseded by BS EN 15234-1:2011
  • DD CEN/TS 15357:2006 Solid recovered fuels. Terminology, definitions and descriptions
    Superseded by BS EN 15357:2011
  • DD CEN/TS 15358:2006 Solid recovered fuels. Quality management systems. Particular requirements for their application to the production of solid recovered fuels
    Superseded by BS EN 15358:2011
    DD CEN/TS 15400:2006 Solid recovered fuels. Methods for the determination of calorific value
    Superseded by BS EN 15400:2011
  • DD CEN/TS 15402:2006 Solid recovered fuels. Methods for the determination of the content of volatile matter
    Superseded by BS EN 15402:2011
  • DD CEN/TS 15403:2006 Solid recovered fuels. Methods for the determination of ash content
    Superseded by BS EN 15403:2011
  • DD CEN/TS 15407:2006 Solid recovered fuels. Method for the determination of carbon (C), hydrogen (H) and nitrogen (N) content
    Superseded by BS EN 15407:2011
  • DD CEN/TS 15408:2006 Solid recovered fuels. Methods for the determination of sulphur (S), chlorine (Cl), fluorine (F) and bromine (Br) content
    Superseded by BS EN 15408:2011
  • DD CEN/TS 15414-3:2006 Solid recovered fuels. Determination of moisture content using the oven dry method. Moisture in general analysis sample
    Superseded by BS EN 15414-3:2011
  • DD C EN/TS 15442:2006 Solid recovered fuels. Methods for sampling
    Superseded by BS EN 15442:2011
  • DD CEN/TS 15443:2006 Solid recovered fuels. Methods for laboratory sample preparation
    Superseded by BS EN 15443:2011
  • BS EN 28029:1993 (ISO 8029:1985) Plastics hose. General purpose collapsible water hose, textile reinforced. Specification
    Superseded by BS EN ISO 8029:2010
  • BS EN 61347-1:2001+A1:2008 Lamp controlgear. General and safety requirements
    Superseded by BS EN 61347-1:2008
  • BS EN 61491:1999 Electrical equipment of industrial machines. Serial data link for real-time communication between controls and drives
    Superseded by BS EN 61158-2:2008, BS EN 61158-3-16:2008, BS EN 61158-4-16:2008, BS EN 61158-5-16:2008, BS EN 61158-6-16:2008, BS EN 61784-1:2008, BS EN 61800-7-1:2008, BS EN 61800-7-204:2008, BS EN 61800-7-304:2008 and PD IEC/TR 61491:2010
  • BS ISO/IEC 9126-1:2001 Information technology. Software product quality. Quality model
    Superseded by BS ISO/IEC 25010:2011
  • BS ISO/IEC 14598-1:1999 Information technology. Software production evaluation. General overview
    Superseded by BS ISO/IEC 25040:2011
  • DD ISO/TS 21667:2004 Health informatics. Health indicators conceptual framework
    Superseded by BS ISO 21667:2010
  • DD IEC/PAS 62562:2008 Cavity resonator method to measure the complex permittivity of low-loss dielectric plates
    Superseded by BS EN 62562:2011

Published in international.