BRITISH STANDARDS

The following are British Standard implementations of the English language versions of European Standards (ENs). The date referenced in the identifier is the date of the European Standard.

  • BS EN 201:2009 Plastics and rubber machines. Injection moulding machines. Safety requirements
    Supersedes BS EN 201:1997
  • BS EN 287-6:2010 Qualification test of welders. Fusion welding. Cast iron
  • BS EN 599-1:2009 Durability of wood and wood-based products. Efficacy of preventive wood preservatives as determined by biological tests. Specification according to use class
    Supersedes BS EN 599-1:1997
  • BS EN 843-6:2009 Advanced technical ceramics. Mechanical properties of monolithic ceramics at room temperature. Guidance for fractographic investigation
    Supersedes DD CEN/TS 843-6:2004
  • BS EN 1020:2009 Non-domestic forced convection gas-fired air heaters for space heating not exceeding a net heat input of 300 kW incorporating a fan to assist transportation of combustion air or combustion products
    Supersedes BS EN 1020:1998
  • BS EN 1047-2:2009 Secure storage units. Classification and methods of test for resistance to fire. Data rooms and data container
    Supersedes BS EN 1047-2:2000
  • BS EN 1230-1:2009 Paper and board intended to come into contact with foodstuffs. Sensory analysis. Odour
    Supersedes BS EN 1230-1:2001
  • BS EN 1282-2:2005+A1:2009 Tracheostomy tubes. Paediatric tubes
    Supersedes BS EN 1282-2:1997
  • BS EN 1319:2009 Domestic gas-fired forced convection air heaters for space heating, with fan-assisted burners not exceeding a net heat input of 70 kW
    Supersedes BS EN 1319:1999
  • BS EN ISO 1452-1:2009 Plastics piping systems for water supply and for buried and above-ground drainage and sewerage under pressure. Unplasticized poly(vinyl chloride) (PVC U). General
    Supersedes BS EN 1452-1:1999 and BS EN 1456-1:2001
  • BS EN ISO 1452-2:2009 Plastics piping systems for water supply and for buried and above-ground drainage and sewerage under pressure. Unplasticized poly(vinyl chloride) (PVC U). Pipes
    Supersedes BS EN 1452-2:1999 and BS EN 1456-1:2001
  • BS EN ISO 1452-3:2009 Plastics piping systems for water supply and for buried and above-ground drainage and sewerage under pressure. Unplasticized poly(vinyl chloride) (PVC U). Fittings
    Supersedes BS EN 1452-3:1999 and BS EN 1456-1:2001
  • BS EN ISO 1452-4:2009 Plastics piping systems for water supply and for buried and above-ground drainage and sewerage under pressure. Unplasticized poly(vinyl chloride) (PVC U). Valves
    Supersedes BS EN 1452-4:1999 and BS EN 1456-1:2001
  • BS EN ISO 1452-5:2009 Plastics piping systems for water supply and for buried and above-ground drainage and sewerage under pressure. Unplasticized poly(vinyl chloride) (PVC U). Fitness for purpose of the system
    Supersedes BS EN 1452-5:1999 and BS EN 1456-1:2001
  • BS EN 1515-4:2009 Flanges and their joints. Bolting. Selection of bolting for equipment subject to the Pressure Equipment Directive 97/23/EC
  • BS EN 1708-1:2010 Welding. Basic welded joint details in steel. Pressurized components
    Supersedes BS EN 1708-1:1999
  • BS EN 1822-2:2009 High efficiency air filters (EPA, HEPA and ULPA). Aerosol production, measuring equipment, particle counting statistics
    Supersedes BS EN 1822-2:1998
  • BS EN 1822-4:2009 High efficiency air filters (EPA, HEPA and ULPA). Determining leakage of filter elements (scan method)
    Supersedes BS EN 1822-4:2000
  • BS EN 1822-5:2009 High efficiency air filters (EPA, HEPA and ULPA). Determining the efficiency of filter elements
    Supersedes BS EN 1822-5:2000
  • BS EN 1858:2008 Chimneys. Components. Concrete flue blocks
    Supersedes BS EN 1858:2003
  • BS EN 2240-003:2010 Aerospace series. Lamps, incandescent. Lamp, code 44. Product standard
  • BS EN 2240-004:2010 Aerospace series. Lamps, incandescent. Lamp, code 47. Product standard
  • BS EN 2240-010:2010 Aerospace series. Lamps, incandescent. Lamp, code 84. Product standard
  • BS EN 2714-014:2009 Aerospace series. Cables, electrical, single and multicore for general purpose. Operating temperatures between -55ºC and 260ºC. DR family, 5 to 10 cores, taped, screened (braided) and jacketed, UV laser printable. Product standard
  • BS EN 2817:2009 Aerospace series. Steel FE-PM1802 (X5CrNiCu15-5). Consumable electrode remelted. Solution treated and precipitation treated. Bar for machining. a or D ? 200 mm. Rm ? 1070 MPa
  • BS EN 2862:2009 Aerospace series. Nuts, anchor, self-locking, fixed, 90º corner, with counterbore, in alloy steel, cadmium plated, MoS2 lubricated. Classification: 1100 MPa (at ambient temperature)/235ºC
  • BS EN 2865:2009 Aerospace series. Nuts, anchor, self-locking, floating, two lugs, with counterbore, in heat resisting steel, MoS2 lubricated. Classification: 1100 MPa (at ambient temperature)/315ºC
  • BS EN 2867:2009 Aerospace series. Nuts, anchor, self-locking, floating, one lug, with counterbore, in heat resisting steel, MoS2 lubricated. Classification: 1100 MPa (at ambient temperature)/315ºC
  • BS EN 2869:2009 Aerospace series. Nuts, hexagonal, slotted/castellated, normal height, normal across flats, in heat resisting steel, passivated. Classification: 1100 MPa (at ambient temperature)/650ºC
  • BS EN ISO 3093:2009 Wheat, rye and their flours, durum wheat and durum wheat semolina. Determination of the falling number according to Hagberg-Perten
    Supersedes BS EN ISO 3093:2007
  • BS EN 3229:2009 Aerospace series. Nuts, hexagonal, plain, reduced height, normal across flats, in steel, cadmium plated, left hand thread. Classification: 900 MPa (at ambient temperature)/235ºC
  • BS EN 3388:2009 Aerospace series. Fasteners, externally threaded, in heat resisting nickel base alloy NI-PH2601 (Inconel 718). Classification 1275 MPa/650ºC. Manufacturing method optional. Technical specification
  • BS EN 3456:2009 Aerospace series. Titanium alloy TIP64001 (Ti-6Al-4V). Annealed. Sheet and strip, hot rolled. a ? 6 mm
  • BS EN 3660-003:2009 Aerospace series. Cable outlet accessories for circular and rectangular electrical and optical connectors. Grommet nut, style A for EN 2997 and EN 4067. Product standard
    Supersedes BS EN 3660-003:2006
  • BS EN 3660-062:2009 Aerospace series. Cable outlet accessories for circular and rectangular electrical and optical connectors. Cable outlet, style K, 90ºC, for heat shrinkable boot, shielded, sealed, self-locking for EN 3645. Product standard
  • BS EN 3660-063:2009 Aerospace series. Cable outlet accessories for circular and rectangular electrical and optical connectors. Cable outlet, style K, straight, for heat shrinkable boot, shielded, sealed, self-locking for EN 3645. Product standard
  • BS EN 3660-064:2009 Aerospace series. Cable outlet accessories for circular and rectangular electrical and optical connectors. Cable outlet, style K, straight, for heat shrinkable boot, shielded, sealed, self-locking for EN 2997 and EN 4067. Product standard
  • BS EN 3660-065:2009 Aerospace series. Cable outlet accessories for circular and rectangular electrical and optical connectors. Cable outlet, style K, 90º, for heat shrinkable boot, shielded, sealed, self-locking for EN 2997 and EN 4067. Product standard
  • BS EN 4073:2009 Aerospace series. Screws, pan head, six lobe recess, coarse tolerance normal shank, medium length thread, in alloy steel, cadmium plated. Classification: 1100 MPa (at ambient temperature)/235ºC
  • BS EN 4078:2009 Aerospace series. Inserts, threaded, thin wall, locked and self-locking, in heat resisting steel, MoS2 lubricated. Classification: 1100 MPa (at ambient temperature)/315ºC
  • BS EN ISO 4080:2009 Rubber and plastics hoses and hose assemblies. Determination of permeability to gas
    Supersedes BS EN ISO 4080:1995
  • BS EN 4084:2009 Aerospace series. Nuts, anchor, self-locking, fixed, two lug, with counterbore, in alloy steel, cadmium plated, MoS2 lubricated. Classification: 1100 MPa (at ambient temperature)/235ºC
  • BS EN 4138:2009 Aerospace series. Screws, pan head, offset cruciform recess, coarse tolerance normal shank, medium length thread, in alloy steel, cadmium plated. Classification: 1100 MPa (at ambient temperature)/235ºC
  • BS EN 4161:2009 Aerospace series. Screws, pan head, offset cruciform recess, coarse tolerance normal shank, long thread, in alloy steel, cadmium plated. Classification: 1100 MPa (at ambient temperature)/235ºC
  • BS EN 4162:2009 Aerospace series. Screws 100º countersunk normal head, offset cruciform recess, coarse tolerance normal shank, medium length thread, in alloy steel, cadmium plated. 1100 MPa (at ambient temperature)/235ºC
  • BS EN 4163:2009 Aerospace series. Screws 100º countersunk normal head, offset cruciform recess, coarse tolerance normal shank, long thread, in alloy steel, cadmium plated. 1100 MPa (at ambient temperature)/235ºC
  • BS EN 4634:2009 Aerospace series. Screws, 100º countersunk head, six lobe recess, short thread, in heat resisting steel FE-PA2601 (A286), passivated. Classification: 900 MPa (at ambient temperature)/650ºC
  • BS EN 4645-002:2009 Aerospace series. Connectors, optical, circular, single and multipin, coupled by threaded ring, self-locking 1,25 mm diameter ferrule with removable alignment sleeve holder. Specification of performance and contact arrangements
  • BS EN 4645-003:2009 Aerospace series. Connectors, optical, circular, single and multipin, coupled by threaded ring, self-locking 1,25 mm diameter ferrule with removable alignment sleeve holder. Square flange receptacle. Product standard
  • BS EN 4645-004:2009 Aerospace series. Connectors, optical, circular, single and multipin, coupled by threaded ring, self-locking 1,25 mm diameter ferrule with removable alignment sleeve holder. Jam nut receptacle. Product standard
  • BS EN 4645-005:2009 Aerospace series. Connectors, optical, circular, single and multipin, coupled by threaded ring, self-locking 1,25 mm diameter ferrule with removable alignment sleeve holder. Plug. Product standard
  • BS EN 6059-502:2009 Aerospace series. Electrical cables, installation. Protection sleeves. Test methods. Resistance to electrical arcs
  • BS EN ISO 7439:2009 Copper-bearing intra-uterine contraceptive devices. Requirements, tests
    Supersedes BS EN ISO 7439:2002
  • BS EN ISO 8362-1:2009 Injection containers and accessories. Injection vials made of glass tubing
    Supersedes BS EN ISO 8362-1:2004
  • BS EN ISO 9241-302:2008 Ergonomics of human-system interaction. Terminology for electronic visual displays
    Supersedes BS EN 29241-3:1993, BS EN ISO 13406-1:1999, BS EN ISO 13406-2:2002, BS EN ISO 9241-7:1998 and BS EN ISO 9241-8:1998
  • BS EN ISO 9241-303:2008 Ergonomics of human-system interaction. Requirements for electronic visual displays
    Supersedes BS EN 29241-3:1993, BS EN ISO 13406-1:1999, BS EN ISO 13406-2:2002, BS EN ISO 9241-7:1998 and BS EN ISO 9241-8:1998
  • BS EN ISO 9241-304:2008 Ergonomics of human-system interaction. User performance test methods for electronic visual displays
    Supersedes BS EN 29241-3:1993, BS EN ISO 13406-1:1999, BS EN ISO 13406-2:2002, BS EN ISO 9241-7:1998 and BS EN ISO 9241-8:1998
  • BS EN ISO 9241-305:2008 Ergonomics of human-system interaction. Optical laboratory test methods for electronic visual displays
    Supersedes BS EN 29241-3:1993, BS EN ISO 13406-1:1999, BS EN ISO 13406-2:2002, BS EN ISO 9241-7:1998 and BS EN ISO 9241-8:1998
  • BS EN ISO 9241-307:2008 Ergonomics of human-system interaction. Analysis and compliance test methods for electronic visual displays
    Supersedes BS EN 29241-3:1993, BS EN ISO 13406-1:1999, BS EN ISO 13406-2:2002, BS EN ISO 9241-7:1998 and BS EN ISO 9241-8:1998
  • BS EN ISO 9801:2009 Ophthalmic instruments. Trial case lenses
    Supersedes BS EN ISO 9801:1999
  • BS EN ISO 9920:2009 Ergonomics of the thermal environment. Estimation of thermal insulation and water vapour resistance of a clothing ensemble
    Supersedes BS EN ISO 9920:2007
  • BS EN ISO 10325:2009 Fibre ropes. High modulus polyethylene. 8-strand braided ropes, 12-strand braided ropes and covered ropes
  • BS EN ISO 10360-2:2009 Geometrical product specifications (GPS). Acceptance and reverification tests for coordinate measuring machines (CMM). CMMs used for measuring linear dimensions
    Supersedes BS EN ISO 10360-2:2002
  • BS EN ISO 10426-1:2009 Petroleum and natural gas industries. Cements and materials for well cementing. Specification
    Supersedes BS EN ISO 10426-1:2006
  • BS EN ISO 10554:2009 Polyamide fibre ropes. Double braid construction
  • BS EN ISO 10991:2009 Micro process engineering. Vocabulary
  • BS EN ISO 10993-4:2009 Biological evaluation of medical devices. Selection of tests for interactions with blood
    Supersedes BS EN ISO 10993-4:2002
  • BS EN ISO 10993-10:2009 Biological evaluation of medical devices. Tests for irritation and delayed-type hypersensitivity
    Supersedes BS EN ISO 10993-10:2002
  • BS EN ISO 11140-3:2009 Sterilization of health care products. Chemical indicators. Class 2 indicator systems for use in the Bowie and Dick-type steam penetration test
    Supersedes BS EN ISO 11140-3:2007
  • BS EN ISO 11701:2009 Vegetable fats and oils. Determination of phospholipids content in lecithins by HPLC using a light-scattering detector
  • BS EN ISO 11702:2009 Animal and vegetable fats and oils. Enzymatic determination of total sterols content
  • BS EN 12697-5:2009 Bituminous mixtures. Test methods for hot mix asphalt. Determination of the maximum density
    Supersedes BS EN 12697-5:2002
  • BS EN ISO 12706:2009 Non-destructive testing. Penetrant testing. Vocabulary
    Supersedes BS EN ISO 12706:2001
  • BS EN 12817:2010 LPG equipment and accessories. Inspection and requalification of LPG tanks up to and including 13 m3
    Supersedes BS EN 12817:2002 and BS EN 12818:2002
  • BS EN 12819:2009 LPG equipment and accessories. Inspection and requalification of LPG tanks greater than 13 m3
    Supersedes BS EN 12819:2002 and BS EN 12820:2002
  • BS EN ISO 12966-3:2009 Animal and vegetable fats and oils. Gas chromatography of fatty acid methyl esters. Preparation of methyl esters using trimethylsulfonium hydroxide
  • BS EN 13146-9:2009 Railway applications. Track. Test methods for fastening systems. Determination of stiffness
  • BS EN 13415:2010 Test of adhesives for floor covering. Determination of the electrical resistance of adhesive films and composites
    Supersedes BS EN 13415:2002
  • BS EN ISO 13628-5:2009 Petroleum and natural gas industries. Design and operation of subsea production systems. Subsea umbilicals
    Supersedes BS ISO 13628-5:2002
  • BS EN 14012:2008 Postal services. Quality of service. Complaints handling principles
    Supersedes BS EN 14012:2003
  • BS EN ISO 14155-1:2009 Clinical investigation of medical devices for human subjects. General requirements
    Supersedes BS EN ISO 14155-1:2003
  • BS EN ISO 14155-2:2009 Clinical investigation of medical devices for human subjects. Clinical investigation plans
    Supersedes BS EN ISO 14155-2:2003
  • BS EN ISO 14161:2009 Sterilization of health care products. Biological indicators. Guidance for the selection, use and interpretation of results
    Supersedes BS EN ISO 14161:2001
  • BS EN 14303:2009 Thermal insulation products for building equipment and industrial installations. Factory made mineral wool products (MW). Specification
  • BS EN 14305:2009 Thermal insulation products for building equipment and industrial installations. Factory made cellular glass (CG) products. Specification
  • BS EN ISO 14602:2009 Non-active surgical implants. Implants for Osteosynthesis. Particular requirements
    Supersedes BS EN ISO 14602:1998
  • BS EN 14636-1:2009 Plastics piping systems for non-pressure drainage and sewerage. Polyester resin concrete (PRC). Pipes and fittings with flexible joints
  • BS EN 14636-2:2009 Plastics piping systems for non-pressure drainage and sewerage. Polyester resin concrete (PRC). Manholes and inspection chambers
  • BS EN 14774-1:2009 Solid biofuels. Determination of moisture content. Oven dry method. Total moisture. Reference method
    Supersedes DD CEN/TS 14774-1:2004
  • BS EN 14774-2:2009 Solid biofuels. Determination of moisture content. Oven dry method. Total moisture. Simplified method
    Supersedes DD CEN/TS 14774-2:2004
  • BS EN 14774-3:2009 Solid biofuels. Determination of moisture content. Oven dry method. Moisture in general analysis sample
    Supersedes DD CEN/TS 14774-3:2004
  • BS EN 14879-6:2009 Organic coating systems and linings for protection of industrial apparatus and plants against corrosion caused by aggressive media. Combined linings with tile and brick layers
  • BS EN 15129:2009 Anti-seismic devices
  • BS EN 15140:2006 Public passenger transport. Basic requirements and recommendations for systems that measure delivered service quality
  • BS EN 15649-4:2010 Floating leisure articles for use on and in the water. Additional specific safety requirements and test methods for Class B devices
  • BS EN 15665:2009 Ventilation for buildings. Determining performance criteria for residential ventilation systems
  • BS EN 15689:2009 Railway applications. Track. Switches and crossings. Crossing components made of cast austenitic manganese steel
  • BS EN 15695-1:2009 Agricultural tractors and self-propelled sprayers. Protection of the operator (driver) against hazardous substances. Cab classification, requirements and test procedures
  • BS EN 15719:2009 Sanitary appliances. Baths made from impact modified coextruded ABS/acrylic sheets. Requirements and test methods
  • BS EN 15720:2009 Sanitary appliances. Shower trays made from impact modified coextruded ABS/acrylic sheets. Requirements and test methods
  • BS EN 15744:2009 Film identification. Minimum set of metadata for cinematographic works
  • BS EN 15763:2009 Foodstuffs. Determination of trace elements. Determination of arsenic, cadmium, mercury and lead in foodstuffs by inductively coupled plasma mass spectrometry (ICP-MS) after pressure digestion
  • BS EN 15764:2009 Foodstuffs. Determination of trace elements. Determination of tin by flame and graphite furnace atomic absorption spectrometry (FAAS and GFAAS) after pressure digestion
  • BS EN 15765:2009 Foodstuffs. Determination of trace elements. Determination of tin by inductively coupled plasma mass spectrometry (ICP-MS) after pressure digestion
  • BS EN 15801:2009 Conservation of cultural property. Test methods. Determination of water absorption by capillarity
  • BS EN 15802:2009 Conservation of cultural property. Test methods. Determination of static contact angle
  • BS EN 15803:2009 Conservation of cultural property. Test methods. Determination of water vapour permeability (?p)
  • BS EN 15805:2009 Particulate air filters for general ventilation. Standardised dimensions
  • BS EN 15826:2009 Vitreous and porcelain enamels. Terminology
  • BS EN 15837:2009 (BS 2000-581:2009) Ethanol as a blending component for petrol. Determination of phosphorus, copper and sulfur content. Direct method by inductively coupled plasma optical emission spectrometry (ICP OES)
  • BS EN 15856:2010 Non-destructive testing. Acoustic emission. General principles of AE testing for the detection of corrosion within metallic surrounding filled with liquid
  • BS EN 15857:2010 Non-destructive testing. Acoustic emission. Testing of fibre-reinforced polymers. Specific methodology and general evaluation criteria
  • BS EN ISO 15927-2:2009 Hygrothermal performance of buildings. Calculation and presentation of climatic data. Hourly data for design cooling load
  • BS EN ISO 18113-1:2009 In vitro diagnostic medical devices. Information supplied by the manufacturer (labelling). Terms, definitions and general requirements
  • BS EN ISO 18113-2:2009 In vitro diagnostic medical devices. Information supplied by the manufacturer (labelling). In vitro diagnostic reagents for professional use
    Supersedes BS EN 375:2001
  • BS EN ISO 18113-3:2009 In vitro diagnostic medical devices. Information supplied by the manufacturer (labelling). In vitro diagnostic instruments for professional use
    Supersedes BS EN 591:2001
  • BS EN ISO 18113-5:2009 In vitro diagnostic medical devices. Information supplied by the manufacturer (labelling). In vitro diagnostic instruments for self-testing
    Supersedes BS EN 592:2002
  • BS EN ISO 18592:2009 Resistance welding. Destructive testing of welds. Method for the fatigue testing of multispot-welded specimens
  • BS EN ISO 19115-2:2010 Geographic information. Metadata. Extensions for imagery and gridded data
  • BS EN ISO 19126:2009 Geographic information. Feature concept dictionaries and registers
  • BS EN ISO 19901-6:2009 Petroleum and natural gas industries. Specific requirements for offshore structures. Marine operations
  • BS EN ISO 22391-1:2009 Plastics piping systems for hot and cold water installations. Polyethylene of raised temperature resistance (PE-RT). General
  • BS EN ISO 22391-2:2009 Plastics piping systems for hot and cold water installations. Polyethylene of raised temperature resistance (PE-RT). Pipes
  • BS EN ISO 22391-3:2009 Plastics piping systems for hot and cold water installations. Polyethylene of raised temperature resistance (PE-RT). Fittings
  • BS EN ISO 22391-5:2009 Plastics piping systems for hot and cold water installations. Polyethylene of raised temperature resistance (PE-RT). Fitness for purpose of the system
  • BS EN 50090-3-3:2009 Home and building electronic systems (HBES). Aspects of application. HBES Interworking model and common HBES data types
  • BS EN 50119:2009 Railway applications. Fixed installations. Electric traction overhead contact lines
    Supersedes BS EN 50119:2001
  • BS EN 50397-2:2009 Covered conductors for overhead lines and the related accessories for rated voltages above 1 kV AC and not exceeding 36 kV AC. Accessories for covered conductors. Tests and acceptance criteria
  • BS EN 50512:2009 Electrical installations for lighting and beaconing of aerodromes. Advanced visual docking guidance systems (A-VDGS)
  • BS EN 50520:2009 Cover plates and cover tapes for the protection and location warning of buried cables or buried conduits in underground installations
  • BS EN 50524:2009 Data sheet and name plate for photovoltaic inverters
  • BS EN 55011:2009 Industrial, scientific and medical equipment. Radio-frequency disturbance characteristics. Limits and methods of measurement
    Supersedes BS EN 55011:2007 which remains current
  • BS EN 60034-15:2009 Rotating electrical machines. Impulse voltage withstand levels of form-wound stator coils for rotating A.C. machines
    Supersedes BS EN 60034-15:1996 which remains current
  • BS EN 60255-26:2009 Measuring relays and protection equipment. Electromagnetic compatibility requirements
    Supersedes BS EN 60255-26:2005
  • BS EN 60269-4:2009 Low-voltage fuses. Supplementary requirements for fuse-links for the protection of semiconductor devices
    Supersedes the dual numbered standard BS EN 60269-4:2007, BS 88-4:2007
  • BS EN 60300-3-11:2009 Dependability management. Application guide. Reliability centred maintenance
  • BS EN 60332-3-10:2009 Tests on electric and optical fibre cables under fire conditions. Test for vertical flame spread of vertically-mounted bunched wires or cables. Apparatus
    Supersedes BS EN 50266-1:2001
  • BS EN 60332-3-21:2009 Tests on electric and optical fibre cables under fire conditions. Test for vertical flame spread of vertically-mounted bunched wires or cables. Category A F/R
    Supersedes BS EN 50266-2-1:2001
  • BS EN 60332-3-22:2009 Tests on electric and optical fibre cables under fire conditions. Test for vertical flame spread of vertically-mounted bunched wires or cables. Category A
    Supersedes BS EN 50266-2-2:2001
  • BS EN 60332-3-23:2009 Tests on electric and optical fibre cables under fire conditions. Test for vertical flame spread of vertically-mounted bunched wires or cables. Category B
    Supersedes BS EN 50266-2-3:2001
  • BS EN 60332-3-24:2009 Tests on electric and optical fibre cables under fire conditions. Test for vertical flame spread of vertically-mounted bunched wires or cables. Category C
    Supersedes BS EN 50266-2-4:2001
  • BS EN 60332-3-25:2009 Tests on electric and optical fibre cables under fire conditions. Test for vertical flame spread of vertically-mounted bunched wires or cables. Category D
    Supersedes BS EN 50266-2-5:2001
  • BS EN 60601-2-20:2009 Medical electrical equipment. Particular requirements for the basic safety and essential performance of infant transport incubators
    Supersedes the dual numbered standard BS EN 60601-2-20:1997, BS 5724-2.120:1997 which remains current
  • BS EN 60603-7-1:2009 Connectors for electronic equipment. Detail specification for 8-way, shielded, free and fixed connectors
    Supersedes BS EN 60603-7-1:2002
  • BS EN 60603-7-2:2009 Connectors for electronic equipment. Detail specification for 8-way, unshielded, free and fixed connectors, for data transmissions with frequencies up to 100 MHz
  • BS EN 60603-7-3:2009 Connectors for electronic equipment. Detail specification for 8-way, shielded, free and fixed connectors, for data transmissions with frequencies up to 100 MHz
  • BS EN 60603-7-5:2009 Connectors for electronic equipment. Detail specification for 8-way, shielded, free and fixed connectors, for data transmissions with frequencies up to 250 MHz
  • BS EN 60603-7:2009 Connectors for electronic equipment. Detail specification for 8-way, unshielded, free and fixed connectors
    Supersedes BS EN 60603-7:1997
  • BS EN 60644:2009 Specification for high-voltage fuse-links for motor circuit application
    Supersedes the dual numbered standard BS EN 60644:1993, BS 5907:1980
  • BS EN 60728-1-2:2009 Cable networks for television signals, sound signals and interactive services. Performance requirements for signals delivered at the system outlet in operation
  • BS EN 60749-20:2009 Semiconductor devices. Mechanical and climatic test methods. Resistance of plastic encapsulated SMDs to the combined effect of moisture and soldering heat
    Supersedes BS EN 60749-20:2003
  • BS EN 60851-2:2009 Winding wires. Test methods. Determination of dimensions
    Supersedes BS EN 60851-2:1998
  • BS EN 60880:2009 Nuclear power plants. Instrumentation and control systems important to safety. Software aspects for computer-based systems performing category A functions
    Supersedes BS IEC 60880:2006
  • BS EN 60904-4:2009 Photovoltaic devices. Reference solar devices. Procedures for establishing calibration traceability
  • BS EN 60947-7-3:2009 Low-voltage switchgear and controlgear. Ancillary equipment. Safety requirements for fuse terminal blocks
    Supersedes BS EN 60947-7-3:2002
  • BS EN 61280-2-3:2009 Fibre optic communication subsystem test procedures. Digital systems. Jitter and wander measurements
    Supersedes BS EN 61280-2-5:1998
  • BS EN 61280-4-1:2009 Fibre optic communication subsystem test procedures. Installed cable plant. Multimode attenuation measurement
    Supersedes BS EN 61280-4-1:2004
  • BS EN 61300-2-12:2009 Fibre optic interconnecting devices and passive components. Basic test and measurement procedures. Tests. Impact
    Supersedes BS EN 61300-2-12:2005
  • BS EN 61439-1:2009 Low-voltage switchgear and controlgear assemblies. General rules
    Supersedes BS EN 60439-1:1999 which remains current
  • BS EN 61439-2:2009 Low-voltage switchgear and controlgear assemblies. Power switchgear and controlgear assemblies
    Supersedes BS EN 60439-1:1999 which remains current
  • BS EN 61547:2009 Equipment for general lighting purposes. EMC immunity requirements
    Supersedes BS EN 61547:1996 which remains current
  • BS EN 61558-2-6:2009 Safety of transformers, reactors, power supply units and similar products for supply voltages up to 1100 V. Particular requirements and tests for safety isolating transformers and power supply units incorporating safety isolating transformers
    Supersedes BS EN 61558-2-6:1998
  • BS EN 61558-2-16:2009 Safety of transformers, reactors, power supply units and similar products for supply voltages up to 1100 V. Particular requirements and tests for switch mode power supply units and transformers for switch mode power supply units
    Supersedes BS EN 61558-2-17:1998
  • BS EN 61606-1:2009 Audio and audiovisual equipment. Digital audio parts. Basic measurement methods of audio characteristics. General
    Supersedes BS EN 61606-1:2004
  • BS EN 61606-2:2009 Audio and audiovisual equipment. Digital audio parts. Basic measurement methods of audio characteristics. Consumer use
    Supersedes BS EN 61606-2:2004
  • BS EN 61753-086-2:2009 Fibre optic interconnecting devices and passive components performance standard. Non-connectorised single-mode bidirectional 1490/1550 nm downstream 1310 nm upstream WWDM devices for category C. Controlled environment
  • BS EN 61968-9:2009 Application integration at electric utilities. System interfaces for distribution management. Interface for meter reading and control
  • BS EN 61987-10:2009 Industrial-process measurement and control. Data structures and elements in process equipment catalogues. Lists of properties (LOPs) for industrial-process measurement and control for electronic data exchange. Fundamentals
  • BS EN 61988-2-3:2009 Plasma display panels. Measuring methods. Image quality. Defects and degradation
  • BS EN 61988-3-2:2009 Plasma display panels. Interface. Electrical interface
  • BS EN 61995-2:2009 Devices for the connection of luminaires for household and similar purposes. Standard sheets for DCL
  • BS EN 62074-1:2009 Fibre optic interconnecting devices and passive components. Fibre optic WDM devices. Generic specification
    Supersedes DD IEC/PAS 62074-1:2007
  • BS EN 62134-1:2009 Fibre optic interconnecting devices and passive components. Fibre optic closures. Generic specification
    Supersedes BS EN 62134-1:2002
  • BS EN 62148-11:2009 Fibre optic active components and devices. Package and interface standards. 14-pin active device modules
    Supersedes BS EN 62148-11:2003
  • BS EN 62149-2:2009 Fibre optic active components and devices. Performance standards. 850 nm discrete vertical cavity surface emitting laser devices
  • BS EN 62223:2009 Insulators. Glossary of terms and definitions
  • BS EN 62267:2009 Railway applications. Automated urban guided transport (AUGT). Safety requirements
    Supersedes DD IEC/PAS 62267:2005
  • BS EN 62379-2:2009 Common control interface for networked digital audio and video products. Audio
  • BS EN 62386-205:2009 Digital addressable lighting interface. Particular requirements for control gear. Supply voltage controller for incandescent lamps (device type 4)
  • BS EN 62386-206:2009 Digital addressable lighting interface. Particular requirements for control gear. Conversion from digital signal into D.C. voltage (device type 5)
  • BS EN 62386-207:2009 Digital addressable lighting interface. Particular requirements for control gear. LED modules (device type 6)
  • BS EN 62446:2009 Grid connected photovoltaic systems. Minimum requirements for system documentation, commissioning tests and inspection
  • BS EN 62448:2009 Multimedia systems and equipment. Multimedia E-publishing and E-books. Generic format for E-publishing
    Supersedes BS IEC 62448:2007
  • BS EN 62453-1:2009 Field device tool (FDT) interface specification. Overview and guidance
  • BS EN 62453-2:2009 Field device tool (FDT) interface specification. Concepts and detailed description
  • BS EN 62453-301:2009 Field device tool (FDT) interface specification. Communication profile integration. IEC 61784 CPF 1
  • BS EN 62453-302:2009 Field device tool (FDT) interface specification. Communication profile integration. IEC 61784 CPF 2
  • BS EN 62453-303-1:2009 Field device tool (FDT) interface specification. Communication profile integration. IEC 61784 CP 3/1 and CP 3/2
  • BS EN 62453-303-2:2009 Field device tool (FDT) interface specification. Communication profile integration. IEC 61784 CP 3/4, CP 3/5 and CP 3/6
  • BS EN 62453-306:2009 Field device tool (FDT) interface specification. Communication profile integration. IEC 61784 CPF 6
  • BS EN 62453-309:2009 Field device tool (FDT) interface specification. Communication profile integration. IEC 61784 CPF 9
  • BS EN 62453-315:2009 Field device tool (FDT) interface specification. Communication profile integration. IEC 61784 CPF 15
  • BS EN 62480:2009 Multimedia home network. Network interfaces for network adapter
  • BS EN 81346-1:2009 Industrial systems, installations and equipment and industrial product. Structuring principles and reference designations. Basic rules
    Supersedes BS EN 61346-1:1996
  • BS EN 81346-2:2009 Industrial systems, installations and equipment and industrial products. Structuring principles and reference designations. Classification of objects and codes for classes
    Supersedes BS EN 61346-2:1996 and DD IEC/PAS 62400:2005

BS ENs implemented by amendment

  • BS EN ISO 17059:2009 Oilseeds. Extraction of oil and preparation of methyl esters of triglyceride fatty acids for analysis by gas chromatography (Rapid method)
    Implementation of European Standard EN ISO 17059 by amendment to BS ISO 17059:2007
  • BS EN ISO 18416:2009 Cosmetics. Microbiology. Detection of Candida albicans
    Implementation of European Standard EN ISO 18416 by amendment to BS ISO 18416:2007
  • BS EN ISO 21148:2009 Cosmetics. Microbiology. General instructions for microbiological examination
    Implementation of European Standard EN ISO 21148 by amendment to BS ISO 21148:2005
  • BS EN ISO 21149:2009 Cosmetics. Microbiology. Enumeration and detection of aerobic mesophilic bacteria
    Implementation of European Standard EN ISO 21149 by amendment to BS ISO 21149:2006

BS implementations

BS Implementations comprise the ISO or IEC text without any national deviation and with front and back cover indicating the UK committee responsible. No other information will normally be added. The date referenced in the identifier is the date of the international standard.

  • BS ISO 639-6:2009 Codes for the representation of names of languages. Alpha-4 code for comprehensive coverage of language variants
  • BS ISO 704:2009 Terminology work. Principles and methods
    Supersedes BS ISO 704:2000
  • BS ISO 1217:2009 Displacement compressors. Acceptance tests
    Supersedes BS ISO 1217:1996
  • BS ISO 1407:2009 Rubber. Determination of solvent extract
    Supersedes BS 7164-3:1992
  • BS ISO 1926:2009 Rigid cellular plastics. Determination of tensile properties
    Supersedes BS ISO 1926:2005
  • BS ISO 2314:2009 Gas turbines. Acceptance tests
    Supersedes BS 3135:1989
  • BS ISO 2531:2009 Ductile iron pipes, fittings, accessories and their joints for water applications
  • BS ISO 2930:2009 Rubber, raw natural. Determination of plasticity retention index (PRI)
    Supersedes BS ISO 2930:1995+A1:2008
  • BS ISO 3046-4:2009 Reciprocating internal combustion engines. Performance. Speed governing
    Supersedes BS 5514-4:1997
  • BS ISO 4468:2009 Gear hobs. Accuracy requirements
    Supersedes BS 5221:1987
  • BS ISO 8026:2009 Agricultural irrigation equipment. Sprayers. General requirements and test methods
  • BS ISO 8434-6:2009 Metallic tube connections for fluid power and general use. 60º cone connectors with or without O-ring
  • BS ISO/IEC 9798-5:2009 Information technology. Security techniques. Entity authentication. Mechanisms using zero knowledge techniques
    Supersedes BS ISO/IEC 9798-5:1999
  • BS ISO 11783-10:2009 Tractors and machinery for agriculture and forestry. Serial control and communications data network. Task controller and management information system data interchange
  • BS ISO/IEC 11889-1:2009 Information technology. Trusted platform module. Overview
  • BS ISO/IEC 12785-1:2009 Information technology. Learning, education, and training. Content packaging. Information model
  • BS ISO 13320:2009 Particle size analysis. Laser diffraction methods
    Supersedes BS ISO 13320-1:1999
  • BS ISO/IEC 13888-3:2009 Information technology. Security techniques. Non-repudiation. Mechanisms using asymmetric techniques
    Supersedes BS ISO/IEC 13888-3:1997
  • BS ISO 14243-2:2009 Implants for surgery. Wear of total knee-joint prostheses. Methods of measurement
    Supersedes BS ISO 14243-2:2000
  • BS ISO/IEC 15408-1:2009 Information technology. Security techniques. Evaluation criteria for IT Security. Introduction and general model
    Supersedes BS ISO/IEC 15408-1:2005
  • BS ISO/IEC 15693-3:2009 Identification cards. Contactless integrated circuit(s) cards. Vicinity cards. Anticollision and transmission protocol
    Supersedes BS ISO/IEC 15693-3:2001
  • BS ISO/IEC 15909-2:2009 Software and system engineering. High-level Petri nets. Transfer Format
  • BS ISO/IEC 15944-7:2009 Information technology. Business operational view. eBusiness vocabulary
  • BS ISO 16000-23:2009 Indoor air. Performance test for evaluating the reduction of formaldehyde concentrations by sorptive building materials
  • BS ISO 16000-24:2009 Indoor air. Performance test for evaluating the reduction of volatile organic compound (except formaldehyde) concentrations by sorptive building materials
  • BS ISO 16245:2009 Information and documentation. Boxes, file covers and other enclosures, made from cellulosic materials, for storage of paper and parchment documents
  • BS ISO/IEC 16326:2009 Systems and software engineering. Life cycle processes. Project management
    Supersedes BS ISO/IEC 16326:1999
  • BS ISO 17103:2009 Agricultural machinery. Rotary disc mowers, rotary drum mowers and flail mowers. Test methods and acceptance criteria for protective skirts
  • BS ISO 17364:2009 Supply chain applications of RFID. Returnable transport items (RTIs)
  • BS ISO 17365:2009 Supply chain applications of RFID. Transport units
  • BS ISO 17874-1:2010 Remote handling devices for radioactive materials. General requirements
  • BS ISO 20022-6:2009 Financial services. UNIversal Financial industry message scheme. Message transport characteristics
  • BS ISO 21438-2:2009 Workplace atmospheres. Determination of inorganic acids by ion chromatography. Volatile acids, except hydrofluoric acid (hydrochloric acid, hydrobromic acid and nitric acid)
  • BS ISO 21610:2009 Corrosion of metals and alloys. Accelerated corrosion test for intergranular corrosion susceptibility of austenitic stainless steels
  • BS ISO 21809-4:2009 Petroleum and natural gas industries. External coatings for buried or submerged pipelines used in pipeline transportation systems. Polyethylene coatings (2-layer PE)
  • BS ISO 22009:2009 Space systems. Space environment (natural and artificial). Model of the earth's magnetospheric magnetic field
  • BS ISO 22201:2009 Lifts (elevators). Design and development of programmable electronic systems in safety related applications for lifts (PESSRAL)
  • BS ISO 22935-3:2009 Milk and milk products. Sensory analysis. Guidance on a method for evaluation of compliance with product specifications for sensory properties by scoring
  • BS ISO 23185:2009 Assessment and benchmarking of terminological resources. General concepts, principles and requirements
  • BS ISO 24095:2009 Workplace air. Guidance for the measurement of respirable crystalline silica
  • BS ISO 24153:2009 Random sampling and randomization procedures
  • BS ISO 26428-9:2009 Digital cinema (D-cinema) distribution master. Image pixel structure level 3. Serial digital interface signal formatting
  • BS ISO 26430-4:2009 Digital cinema (D-cinema) operations. Log record format specification
  • BS ISO 26433:2009 Digital cinema (D-cinema). XML data types
  • BS ISO/IEC 26513:2009 Systems and software engineering. Requirements for testers and reviewers of user documentation
  • BS ISO 26866:2009 Road vehicles. Brake lining friction materials. Standard wear test procedure for commercial vehicles with air brakes
  • BS ISO/IEC 27004:2009 Information technology. Security techniques. Information security management. Measurement
  • BS ISO/IEC 27033-1:2009 Information technology. Security techniques. Network security. Overview and concepts
    Supersedes BS ISO/IEC 18028-1:2006
  • BS ISO 27327-1:2009 Fans. Air curtain units. Laboratory methods of testing for aerodynamic performance rating
  • BS ISO 27895:2009 Vacuum technology. Valves. Leak test
  • BS ISO 28219:2009 Packaging. Labelling and direct product marking with linear bar code and two-dimensional symbols
  • BS ISO/IEC 29141:2009 Information technology. Biometrics. Tenprint capture using biometric application programming interface (BioAPI)
  • BS ISO 29802:2009 All terrain (AT) tyres and rims. Symbol marked pneumatic tyres on 5 degrees tapered rims. Designation, dimension, marking and load ratings
  • BS ISO 29945:2009 Refrigerated non-petroleum-based liquefied gaseous fuels. Dimethylether (DME). Method of manual sampling onshore terminals
  • BS IEC 61500:2009 Nuclear power plants. Instrumentation and control important to safety. Data communication in systems performing category A functions
  • BS ISO 80000-1:2009 Quantities and units. General
    Supersedes BS ISO 1000:1992 and BS ISO 31-0:1992
  • BS ISO 80000-2:2009 Quantities and units. Mathematical signs and symbols to be used in the natural sciences and technology
    Supersedes BS ISO 31-11:1992
  • BS ISO 80000-10:2009 Quantities and units. Atomic and nuclear physics
    Supersedes BS ISO 31-9:1992 and BS ISO 31-10:1992

Aerospace series

  • BS 2HC 100:2010 Procedure for inspection, testing and acceptance of iron, nickel, copper, cobalt and refractory metal base alloy castings
    Supersedes BS HC 100:1972
  • BS 3HR 1:2010 Specification for nickel-chromium-titanium-aluminium heat-resisting alloy billets, bars, forgings and parts (nickel base, Cr 19.5, Ti 2.2, Al 1.4)
    Supersedes BS 2HR 1:1973
  • BS 3HR 2:2010 Aerospace series. Specification for nickel-chromium-cobalt-titanium-aluminium heat-resisting alloy billets, bars, forgings and parts (nickel base, Cr 19.5, Co 18.0, Ti 2.5, Al 1.5)
    Supersedes BS 2HR 2:1973
  • BS 2HR 3:2010 Specification for nickel-cobalt-chromium-molybdenum-aluminium-titanium heat-resisting alloy billets, bars, forgings and parts (nickel base, Co 20, Cr 14. 8, Mo 5, Al 4.8, Ti 1.2)
    Supersedes BS HR 3:1972
  • BS 2HR 4:2010 Specification for nickel-chromium-cobalt-aluminium-molybdenum-titanium heat-resisting alloy billets, bars, forgings and parts (nickel base, Cr 15, Co 14. 2, Al 5, Mo 4, Ti 4)
    Supersedes BS HR 4:1972
  • BS 2HR 5:2010 Specification for nickel-chromium-titanium heat-resisting alloy billets, bars, forgings and parts (nickel base, Cr 19.5, Ti 0. 4)
    Supersedes BS HR 5:1972
  • BS 2HR 6:2010 Specification for nickel-chromium-iron-molybdenum-cobalt-tungsten heat-resisting alloy billets, bars, forgings and parts (nickel base, Cr 21.7, Fe 18.5, Mo 9, Co 1.5, W 0.6)
    Supersedes BS HR 6:1972
  • BS 2HR 10:2010 Specification for nickel-cobalt-chromium-molybdenum-titanium-aluminium heat-resisting alloy billets, bars, forgings and parts (nickel base, Co 20, Cr 20, Mo 5.9, Ti 2.1, Al 0.5)
    Supersedes BS HR 10:1972
  • BS 2HR 40:2010 Specification for cobalt-chromium-tungsten-nickel-manganese heat-resisting alloy billets, bars and forgings (cobalt base, Cr 20, W 15, Ni 10, Mn 1.5)
    Supersedes BS HR 40:1972
  • BS 2HR 51:2010 Specification for high expansion heat-resisting steel billets, bars, forgings and parts (Ni 25.5, Cr 15, Ti 2, Mn 1.5, Mo 1.25, Si 0.7, V 0.3) (Solution treated at 980ºC)
    Supersedes BS HR 51:1973
  • BS 2HR 52:2010 Specification for heat-resisting steel billets, bars, forgings and parts (Ni 25.5, Cr 14.7, Ti 1.8, Mn 1.5, Mo 1.2, V 0.3)
    Supersedes BS HR 52:1973
  • BS 2HR 53:2010 Specification for nickel-iron-chromium-molybdenum-titanium heat-resisting alloy billets, bars, forgings and parts (Ni/Co 42.5, Cr 12.5, Mo 5.8, Ti 3.0, Fe remainder)
    Supersedes BS HR 53:1973
  • BS 2HR 55:2010 Specification for nickel-iron-chromium-molybdenum-aluminium-titanium heat-resisting alloy billets, bars, forgings and parts (Ni/Co 43.5, Cr 16.5, Mo 3. 3, Al 1.2, Ti 1.2, Fe remainder)
    Supersedes BS HR 55:1980
  • BS 4HR 100:2010 Procedure for inspection, testing and acceptance of wrought heat-resisting alloys
    Supersedes BS 3HR 100:1978

Publicly Available Specifications

Publicly Available Specifications (formerly Product Assessment Specifications) are issued to provide an interim document where there is a market need but where a full Standard has yet to be published.

  • PAS 68:2010 Impact test specifications for vehicle security barriers
    Supersedes PAS 68:2007
  • PAS 800:2010 Dementia care mapping. Code of practice

Corrigenda to British Standards and updated British Standards

Most British amendments are not issued separately. Those that make significant changes to a standard are incorporated into the standard which is re-issued as a new edition. All amendments to date of despatch are included within any main publication when ordered for the first time. The following amended Standards and corrigenda to British Standards were made available last month.

  • BS 1868:1975+A1:1990 Specification for steel check valves (flanged and butt-welding ends) for the petroleum, petrochemical and allied industries
    CORRIGENDUM 1
  • BS 4551:2005+A1:2010 Mortar. Methods of test for mortar. Chemical analysis and physical testing
    AMENDMENT 1
  • BS 4999-141:2004+A1:2010 General requirements for rotating electrical machines. Specification for standard dimensions
    AMENDMENT 1
  • BS 6349-7:1991 Maritime structures. Guide to the design and construction of breakwaters
    CORRIGENDUM 1
  • BS EN 285:2006+A2:2009 Sterilization. Steam sterilizers. Large sterilizers
    AMENDMENT 2
  • BS EN 415-3:1999+A1:2009 Safety of packaging machines. Form, fill and seal machines
    AMENDMENT 1
  • BS EN 415-5:2006+A1:2009 Safety of packaging machines. Wrapping machines
    AMENDMENT 1
  • BS EN 415-6:2006+A1:2009 Safety of packaging machines. Pallet wrapping machines
    AMENDMENT 1
  • BS EN 420:2003+A1:2009 Protective gloves. General requirements and test methods
    AMENDMENT 1
  • BS EN 500-1:2006+A1:2009 Mobile road construction machinery. Safety. Common requirements
    AMENDMENT 1
  • BS EN 520:2004+A1:2009 Gypsum plasterboards. Definitions, requirements and test methods
    AMENDMENT 1
  • BS EN 786:1996+A2:2009 Garden equipment. Electrically powered walk-behind and hand-held lawn trimmers and lawn edge trimmers. Mechanical safety
    AMENDMENT 2
  • BS EN 859:2007+A1:2009 Safety of woodworking machines. Hand fed surface planing machines
    AMENDMENT 1
  • BS EN 860:2007+A1:2009 Safety of woodworking machines. One side thickness planing machines
    AMENDMENT 1
  • BS EN 861:2007+A1:2009 Safety of woodworking machines. Surface planing and thicknessing machines
    AMENDMENT 1
  • BS EN 1017:2008 Chemicals used for treatment of water intended for human consumption. Half-burnt dolomite
    CORRIGENDUM 1
  • BS EN 1018:2006 Chemicals used for treatment of water intended for human consumption. Calcium carbonate
    CORRIGENDUM 2
  • BS EN 1060-2:1995+A1:2009 Non-invasive sphygmomanometers. Supplementary requirements for mechanical sphygmomanometers
    AMENDMENT 1
  • BS EN 1060-3:1997+A2:2009 Non-invasive sphygmomanometers. Supplementary requirements for electromechanical blood pressure measuring systems
    AMENDMENT 2
  • BS EN 1295-1:1997 Structural design of buried pipelines under various conditions of loading. General requirements
    CORRIGENDUM 3
  • BS EN 1755:2000+A1:2009 Safety of industrial trucks. Operation in potentially explosive atmospheres. Use in flammable gas, vapour, mist and dust
    AMENDMENT 1
  • BS EN 1760-1:1997+A1:2009 Safety of machinery. Pressure sensitive protective devices. General principles for the design and testing of pressure sensitive mats and pressure sensitive floors
    AMENDMENT 1
  • BS EN 1760-2:2001+A1:2009 Safety of machinery. Pressure sensitive protective devices. General principles for the design and testing of pressure sensitive edges and pressure sensitive bars
    AMENDMENT 1
  • BS EN 1870-4:2001+A1:2009 Safety of woodworking machines. Circular sawing machines. Multiblade rip sawing machines with manual loading and/or unloading
    AMENDMENT 1
  • BS EN 1870-16:2005+A1:2009 Safety of woodworking machines. Circular sawing machines. Double mitre sawing machines for V-cutting
    AMENDMENT 1
  • BS EN 1993-1-10:2005 Eurocode 3. Design of steel structures. Material toughness and through-thickness properties
    CORRIGENDUM 3
  • BS EN 1993-1-11:2006 Eurocode 3. Design of steel structures. Design of structures with tension components
    CORRIGENDUM 1
  • BS EN 1993-2:2006 Eurocode 3. Design of steel structures. Steel bridges
    CORRIGENDUM 1
  • BS EN 1993-3-1:2006 Eurocode 3. Design of steel structures. Towers, masts and chimneys. Towers and masts
    CORRIGENDUM 1
  • BS EN 1997-1:2004 Eurocode 7. Geotechnical design. General rules
    CORRIGENDUM 1
  • BS EN ISO 3823-2:2003+A1:2008 Dentistry. Rotary bur instruments. Finishing burs
    AMENDMENT 1
  • BS EN ISO 8062-3:2007 Geometrical product specifications (GPS). Dimensional and geometrical tolerances for moulded parts. General dimensional and geometrical tolerances and machining allowances for castings
    CORRIGENDUM 1
  • BS EN ISO 9100-14:2005 Glass containers. Vacuum lug finishes. 110 regular
    CORRIGENDUM 1
  • BS EN ISO 9936:2006 Animal and vegetable fats and oils. Determination of tocopherol and tocotrienol contents by high-performance liquid chromatography
    CORRIGENDUM 1
  • BS EN ISO 11290-1:1996+A1:2004 (BS 5763-18:1997) Microbiology of food and animal feeding stuffs. Horizontal method for the detection and enumeration of Listeria monocytogenes. Detection method
    CORRIGENDUM 2
  • BS EN 12001:2003+A1:2009 Conveying, spraying and placing machines for concrete and mortar. Safety requirements
    AMENDMENT 1
  • BS EN 12505:2000+A1:2009 Food processing machinery. Centrifugal machines for processing edible oils and fats. Safety and hygiene requirements
    AMENDMENT 1
  • BS EN 12750:2001+A1:2009 Safety of woodworking machines. Four-sided moulding machines
    AMENDMENT 1
  • BS EN 12952-1:2001 Water-tube boilers and auxiliary installations. General
    CORRIGENDUM 1
  • BS EN 12952-2:2001 Water-tube boilers and auxiliary installations. Materials for pressure parts of boilers and accessories
    CORRIGENDUM 1
  • BS EN 12952-3:2001 Water-tube boilers and auxiliary installations. Design and calculation of pressure parts
    CORRIGENDUM 1
  • BS EN 12952-5:2001 Water-tube boilers and auxiliary installations. Workmanship and construction of pressure parts of the boiler
    CORRIGENDUM 1
  • BS EN 12952-6:2002 Water-tube boilers and auxiliary installations. Inspection during construction. Documentation and marking of pressure parts of the boiler
    CORRIGENDUM 1
  • BS EN 12952-7:2002 Water-tube boilers and auxiliary installations. Requirements for equipment for the boiler
    CORRIGENDUM 1
  • BS EN 12952-10:2002 Water-tube boilers and auxiliary installations. Requirements for safeguards against excessive pressure
    CORRIGENDUM 1
  • BS EN 12952-11:2007 Water-tube boilers and auxiliary installations. Requirements for limiting devices of the boiler and accessories
    CORRIGENDUM 1
  • BS EN 13035-3:2003+A1:2009 Machines and plants for the manufacture, treatment and processing of flat glass. Safety requirements. Cutting machines
    AMENDMENT 1
  • BS EN 13035-7:2006+A1:2009 Machines and plants for the manufacture, treatment and processing of flat glass. Safety requirements. Cutting machines for laminated glass
    AMENDMENT 1
  • BS EN 13112:2002+A1:2009 Tannery machines. Splitting and bandknife shearing machines. Safety requirements
    AMENDMENT 1
  • BS EN 13114:2002+A1:2009 Tannery machines. Rotating process vessels. Safety requirements
    AMENDMENT 1
  • BS EN 13140:2000+A1:2009 Agricultural machinery. Sugar beet and fodder beet harvesting equipment. Safety
    AMENDMENT 1
  • BS EN 13215:2000 Condensing units for refrigeration. Rating conditions, tolerances and presentation of manufacturer's performance data
    CORRIGENDUM 1
  • BS EN 13263-1:2005+A1:2009 Silica fume for concrete. Definitions, requirements and conformity criteria
    AMENDMENT 1
  • BS EN 13263-2:2005+A1:2009 Silica fume for concrete. Conformity evaluation
    AMENDMENT 1
  • BS EN 13363-1:2003+A1:2007 Solar protection devices combined with glazing. Calculation of solar and light transmittance. Simplified method
    CORRIGENDUM 1
  • BS EN 13384-2:2003+A1:2009 Chimneys. Thermal and fluid dynamic calculation methods. Chimneys serving more than one heating appliance
    AMENDMENT 1
  • BS EN ISO 13500:2008 Petroleum and natural gas industries. Drilling fluid materials. Specifications and tests
    CORRIGENDUM 1
  • BS EN ISO 13503-2:2006+A1:2009 Petroleum and natural gas industries. Completion fluids and materials. Measurement of properties of proppants used in hydraulic fracturing and gravel-packing operations
    AMENDMENT 1
  • BS EN 13674-4:2006+A1:2009 Railway applications. Track. Rail. Vignole railway rails from 27 kg/m to, but excluding 46 kg/m
    AMENDMENT 1
  • BS EN 13803-2:2006+A1:2009 Railway applications. Track. Track alignment design parameters. Track gauges 1435 mm and wider. Switches and crossings and comparable alignment design situations with abrupt changes of curvature
    AMENDMENT 1
  • BS EN 13867:2002+A1:2009 Concentrates for haemodialysis and related therapies
    AMENDMENT 1
  • BS EN 13941:2009 Design and installation of preinsulated bonded pipe systems for district heating
    CORRIGENDUM 1
  • BS EN 14214:2008+A1:2009 Automotive fuels. Fatty acid methyl esters (FAME) for diesel engines. Requirements and test methods
    AMENDMENT 1
  • BS EN 14591-2:2007 Explosion prevention and protection in underground mines. Protective systems. Passive water trough barriers
    CORRIGENDUM 1
  • BS EN 14761:2006+A1:2008 Wood flooring. Solid wood parquet. Vertical finger and module brick
    AMENDMENT 1
  • BS EN 14811:2006+A1:2009 Railway applications. Track. Special purpose rail. Grooved and associated construction
    AMENDMENT 1
  • BS EN 14861:2004+A1:2009 Forest machinery. Self propelled machinery. Safety requirements
    AMENDMENT 1
  • BS EN 14891:2007 Liquid applied water impermeable products for use beneath ceramic tiling bonded with adhesives. Requirements, test methods, evaluation of conformity, classification and designation
    CORRIGENDUM 3
  • BS EN 15030:2006 Chemicals used for treatment of water intended for human consumption. Silver salts for intermittent use
    CORRIGENDUM 1
  • BS EN 15200:2007 Sanitary appliances. Multifunction shower cabinets
    CORRIGENDUM 1
  • BS EN ISO 15463:2003 Petroleum and natural gas industries. Field inspection of new casing, tubing and plain-end drill pipe
    CORRIGENDUM 1
  • BS EN ISO 17059:2009 Oilseeds. Extraction of oil and preparation of methyl esters of triglyceride fatty acids for analysis by gas chromatography (Rapid method)
    CORRIGENDUM 1
  • BS EN ISO 17078-2:2007 Petroleum and natural gas industries. Drilling and production equipment. Flow-control devices for side-pocket mandrels
    CORRIGENDUM 1
  • BS EN ISO 18416:2009 Cosmetics. Microbiology. Detection of Candida albicans
    CORRIGENDUM 1
  • BS EN ISO 21148:2009 Cosmetics. Microbiology. General instructions for microbiological examination
    CORRIGENDUM 1
  • BS EN ISO 21149:2009 Cosmetics. Microbiology. Enumeration and detection of aerobic mesophilic bacteria
    CORRIGENDUM 1
  • BS EN ISO 28300:2008 Petroleum, petrochemical and natural gas industries. Venting of atmospheric and low pressure storage tanks
    CORRIGENDUM 1
  • BS EN 45502-2-2:2008 Active implantable medical devices. Particular requirements for active implantable medical devices intended to treat tachyarrhythmia (includes implantable defibrillators)
    CORRIGENDUM 1
  • BS EN 50274:2002 Low-voltage switchgear and controlgear assemblies. Protection against electric shock. Protection against unintentional direct contact with hazardous live parts
    CORRIGENDUM 1
  • BS EN 50436-2:2007 Alcohol interlocks. Test methods and performance requirements. Instruments having a mouthpiece and measuring breath alcohol for general preventive use
    CORRIGENDUM 1
  • BS EN 55020:2007 Sound and television broadcast receivers and associated equipment. Immunity characteristics. Limits and methods of measurement
    CORRIGENDUM 1
  • BS EN 60311:2003+A2:2009 Electric irons for household or similar use. Methods for measuring performance
    AMENDMENT 2
  • BS EN 60335-2-103:2003 Household and similar electrical appliances. Safety. Particular requirements for drives for gates, doors and windows
    AMENDMENT 11
  • BS EN 60404-5:2007 Magnetic materials. Permanent magnet (magnetically hard) materials. Methods of measurement of magnetic properties
    CORRIGENDUM 1
  • BS EN 61000-4-13:2002+A1:2009 Electromagnetic compatibility (EMC). Testing and measurement techniques. Harmonics and interharmonics including mains signalling at A.C. power port, low frequency immunity tests
    AMENDMENT 1
  • BS EN 61000-4-14:1999+A2:2009 Electromagnetic compatibility (EMC). Testing and measurement techniques. Voltage fluctuation immunity test for equipment with input current not exceeding 16 A per phase
    AMENDMENT 2
  • BS EN 61009-1:2004 Residual current operated circuit-breakers with integral overcurrent protection for household and similar uses (RCBOs). General rules
    AMENDMENT 13
  • BS EN 61290-1-3:2005 Optical amplifiers. Test methods. Power and gain parameters. Optical power meter method
    CORRIGENDUM 1
  • BS EN 61643-21:2001+A1:2009 Low voltage surge protective devices. Surge protective devices connected to telecommunications and signalling networks. Performance requirements and testing methods
    AMENDMENT 1
  • BS EN 61784-5-3:2008 Industrial communication networks. Profiles. Installation of fieldbuses. Installation profiles for CPF 3
    CORRIGENDUM 1
  • BS EN 62040-3:2001 Uninterruptible power systems (UPS). Method of specifying the performance and test requirements
    AMENDMENT 11
  • BS EN 140101-806:2008 Detail Specification. Fixed low power film resistors. Metal film resistors on high grade ceramic, conformal coated or molded, axial or preformed leads
    CORRIGENDUM 1
  • BS QC 750100:1986+A2:1996 (IEC 60747-11:1985) Harmonized system of quality assessment for electronic components. Discrete semiconductor devices. Sectional specification
    AMENDMENT 2
  • BS ISO 1431-1:2004+A1:2009 Rubber, vulcanized or thermoplastic. Resistance to ozone cracking. Static and dynamic strain testing
    AMENDMENT 1
  • BS ISO 1629:1995+A1:2007 Rubber and latices. Nomenclature
    CORRIGENDUM 1
  • BS ISO 3082:2009 Iron ores. Sampling and sample preparation procedures
    CORRIGENDUM 1
  • BS ISO 3664:2009 Graphic technology and photography. Viewing conditions
    CORRIGENDUM 1
  • BS ISO 8454:2007+A1:2009 Cigarettes. Determination of carbon monoxide in the vapour phase of cigarette smoke. NDIR method
    AMENDMENT 1
  • BS ISO 13628-11:2007 Petroleum and natural gas industries. Design and operation of subsea production systems. Flexible pipe systems for subsea and marine applications
    CORRIGENDUM 1
  • BS ISO 16000-17:2008 Indoor air. Detection and enumeration of moulds. Culture-based method
    CORRIGENDUM 1
  • BS ISO 16063-21:2003 Methods for the calibration of vibration and shock transducers. Vibration calibration by comparison to a reference transducer
    CORRIGENDUM 1
  • DD ISO/TS 16281:2008 Rolling bearings. Methods for calculating the modified reference rating life for universally loaded bearings
    CORRIGENDUM 1
  • BS ISO 17572-3:2008 Intelligent transport systems (ITS). Location referencing for geographic databases. Dynamic location references (dynamic profile)
    CORRIGENDUM 1
  • BS ISO/IEC 19784-1:2006+A2:2009 Information technology. Biometric application programming interface. BioAPI specification
    AMENDMENT 2
  • BS ISO/IEC 19794-2:2005 Information technology. Biometric data interchange formats. Finger minutiae data
    CORRIGENDUM 1

British Standards withdrawn

  • BS 88-2.2:1988 Cartridge fuses for voltages up to and including 1000 V A.C. and 1500 V D.C. Specification for fuses for use by authorized persons (mainly for industrial application). Additional requirements for fuses with fuse-links for bolted connections
    Superseded by BS 88-2:2007
  • BS 88-5:1988 Cartridge fuses for voltages up to and including 1000 V A.C. and 1500 V D.C. Specification of supplementary requirements for fuse-links for use in A.C. electricity supply networks
    Superseded by BS 88-2:2007
  • BS 88-6:1988 Cartridge fuses for voltages up to and including 1000 V A.C. and 1500 V D.C. Specification of supplementary requirements for fuses of compact dimensions for use in 240/415 V A.C. industrial and commercial electrical installations
    Superseded by BS 88-2:2007
  • BS 449-2:1969 Specification for the use of structural steel in building. Metric units
    Superseded by BS EN 1993-1-1:2005, BS EN 1993-1-5:2006, BS EN 1993-1-8:2005, BS EN 1993-1-10:2005, BS EN 1993-5:2007 and BS EN 1993-6:2007
  • BS 950-2:1967 Specification for artificial daylight for the assessment of colour. Viewing conditions for the graphic arts industry
    Superseded by BS ISO 3664:2009
  • BS 1361:1971 Specification for cartridge fuses for A.C. circuits in domestic and similar premises
    Superseded by BS 88-3:2007
  • BS 3135:1989 Specification for gas turbine acceptance test
    Superseded by BS ISO 2314:2009
  • BS 4076:1989 Specification for steel chimneys
    Superseded by BS EN 1993-3-2:2006
  • BS 4604-1:1970 Specification for the use of high strength friction grip bolts in structural steelwork. Metric series. General grade
    Superseded by BS EN 1993-1-8:2005
  • BS 4604-2:1970 Specification for the use of high strength friction grip bolts in structural steelwork. Metric series. Higher grade (parallel shank)
    Superseded by BS EN 1993-1-8:2005
  • BS 5221:1987 Specification for general purpose, metric module gear hobs
    Superseded by BS ISO 4468:2009
  • BS 5268-3:2006 Structural use of timber. Code of practice for trussed rafter roofs
    Superseded by BS EN 1995-1-1:2004+A1:2008
  • BS 5268-4.1:1978 Structural use of timber. Fire resistance of timber structures. Recommendations for calculating fire resistance of timber members
    Superseded by BS EN 1995-1-2:2004
  • BS 5268-4.2:1990 Structural use of timber. Fire resistance of timber structures. Recommendations for calculating fire resistance of timber stud walls and joisted floor constructions
    Superseded by BS EN 1995-1-2:2004
  • BS 5268-5:1989 Structural use of timber. Code of practice for the preservative treatment of structural timber
    This standard has been withdrawn as it is no longer relevant
  • BS 5400-1:1988 Steel, concrete and composite bridges. General statement
    Superseded by BS EN 1990:2002+A1:2005 and BS EN 1991-1-7:2006
  • BS 5400-2:2006 Steel, concrete and composite bridges. Specification for loads
    Superseded by BS EN 1990:2002+A1:2005 and BS EN 1991-1-7:2006
  • BS 5400-3:2000 Steel, concrete and composite bridges. Code of practice for design of steel bridges
    Superseded by BS EN 1993-1-1:2005, BS EN 1993-1-5:2006, BS EN 1993-1-8:2005, BS EN 1993-1-10:2005 and BS EN 1993-2:2006
  • BS 5400-4:1990 Steel, concrete and composite bridges. Code of practice for design of concrete bridges
    Superseded by BS EN 1992-2:2005
  • BS 5400-5:2005 Steel, concrete and composite bridges. Code of practice for design of composite bridges
    Superseded by BS EN 1994-2:2005
  • BS 5400-6:1999 Steel, concrete and composite bridges. Specification for materials and workmanship, steel
    Superseded by BS EN 1090-2:2008
  • BS 5400-7:1978 Steel, concrete and composite bridges. Specification for materials and workmanship, concrete, reinforcement and prestressing tendons
    Superseded by BS EN 1992-2:2005
  • BS 5400-8:1978 Steel, concrete and composite bridges. Recommendations for materials and workmanship, concrete, reinforcement and prestressing tendons
    Superseded by BS EN 1992-2:2005
  • BS 5400-10:1980 Steel, concrete and composite bridges. Code of practice for fatigue
    Superseded by BS EN 1993-1-9:2005
  • BS 5514-4:1997 Reciprocating internal combustion engines. Performance. Speed governing
    Superseded by BS ISO 3046-4:2009
  • BS 5628-1:2005 Code of practice for the use of masonry. Structural use of unreinforced masonry
    Superseded by BS EN 1996-1-1:2005, BS EN 1996-2:2006 and BS EN 1996-3:2006
  • BS 5628-2:2005 Code of practice for the use of masonry. Structural use of reinforced and prestressed masonry
    Superseded by BS EN 1996-1-1:2005, BS EN 1996-2:2006 and BS EN 1996-3:2006
  • BS 5628-3:2005 Code of practice for the use of masonry. Materials and components, design and workmanship
    Superseded by BS EN 1996-1-2:2005, BS EN 1996-2:2006 and BS EN 1996-3:2006
  • BS 5950-1:2000 Structural use of steelwork in building. Code of practice for design. Rolled and welded sections
    Superseded by BS EN 1993-1-1:2005, BS EN 1993-1-5:2006, BS EN 1993-1-8:2005, BS EN 1993-1-10:2005, BS EN 1993-5:2007 and BS EN 1993-6:2007
  • BS 5950-2:2001 Structural use of steelwork in building. Specification for materials, fabrication and erection. Rolled and welded sections
    Superseded by BS EN 1090-2:2008
  • BS 5950-4:1994 Structural use of steelwork in building. Code of practice for design of composite slabs with profiled steel sheeting
    Superseded by BS EN 1994-1-1:2004
  • BS 5950-5:1998 Structural use of steelwork in building. Code of practice for design of cold formed thin gauge sections
    Superseded by BS EN 1994-2:2005
  • BS 5950-6:1995 Structural use of steelwork in building. Code of practice for design of light gauge profiled steel sheeting
    Superseded by BS EN 1090-2:2008
  • BS 5950-7:1992 Structural use of steelwork in building. Specification for materials and workmanship: cold formed sections
    This standard has been withdrawn as it is no longer relevant
  • BS 5950-8:2003 Structural use of steelwork in building. Code of practice for fire resistant design
    Superseded by BS EN 1993-1-2:2005
  • BS 5950-9:1994 Structural use of steelwork in building. Code of practice for stressed skin design
    Superseded by BS EN 1993-1-3:2006
  • BS 6399-1:1996 Loading for buildings. Code of practice for dead and imposed loads
    Superseded by BS EN 1991-1-1:2002 and BS EN 1991-1-7:2006
  • BS 6399-2:1997 Loading for buildings. Code of practice for wind loads
    Superseded by BS EN 1991-1-4:2005
  • BS 6399-3:1988 Loading for buildings. Code of practice for imposed roof loads
    Superseded by BS EN 1991-1-3:2003
  • BS 7164-3:1992 Chemical tests for raw and vulcanized rubber. Methods for determination of solvent extract
    Superseded by BS ISO 1407:2009
  • BS 8002:1994 Code of practice for earth retaining structures
    Superseded by BS EN 1997-1:2004
  • BS 8004:1986 Code of practice for foundations
    Superseded by BS EN 1997-1:2004
  • BS 8007:1987 Code of practice for design of concrete structures for retaining aqueous liquids
    Superseded by BS EN 1992-3:2006
  • BS 8100-1:1986 Lattice towers and masts. Code of practice for loading
    Superseded by BS EN 1993-3-1:2006
  • BS 8100-2:1986 Lattice towers and masts. Guide to the background and use of Part 1 'Code of practice for loading'
    Superseded by BS EN 1993-3-1:2006
  • BS 8100-3:1999 Lattice towers and masts. Code of practice for strength assessment of members of lattice towers and masts
    Superseded by BS EN 1993-3-1:2006
  • BS 8100-4:1995 Lattice towers and masts. Code of practice for loading of guyed masts
    Superseded by BS EN 1993-3-1:2006
  • BS 8110-1:1997 Structural use of concrete. Code of practice for design and construction
    Superseded by BS EN 1992-1-1:2004
  • BS 8110-2:1985 Structural use of concrete. Code of practice for special circumstances
    Superseded by BS EN 1992-1-1:2004
  • BS 8110-3:1985 Structural use of concrete. Design charts for singly reinforced beams, doubly reinforced beams and rectangular columns
    Superseded by BS EN 1992-1-1:2004
  • BS 8118-1:1991 Structural use of aluminium. Code of practice for design
    Superseded by BS EN 1999-1-1:2007, BS EN 1999-1-3:2007 and BS EN 1999-1-4:2007
  • BS 8118-2:1991 Structural use of aluminium. Specification for materials, workmanship and protection
    Superseded by BS EN 1999-1-1:2007
  • BS 9090:1977 Variable capacitors of assessed quality: generic data and methods of test
    This standard was partially superseded by BS EN 134000:1995. The clauses which remained current are no longer considered relevant and are now withdrawn
  • DD CEN/TS 81-29:2004 Safety rules for the construction and installation of lifts. Safety rules for the construction and installation of lifts. Lifts for the transport of persons and goods. Interpretations related to EN 81-20 up to EN 81-28 (includes EN 81-1:1998 and EN 81-2:1998)
    Superseded by DD CEN/TS 81-11:2009
  • BS EN 375:2001 Information supplied by the manufacturer with in vitro diagnostic reagents for professional use
    Superseded by BS EN ISO 18113-2:2009
  • BS EN 591:2001 Instructions for use for in vitro diagnostic instruments for professional use
    Superseded by BS EN ISO 18113-3:2009
  • BS EN 592:2002 Instructions for use for in vitro diagnostic instruments for self-testing
    Superseded by BS EN ISO 18113-5:2009
  • DD CEN/TS 843-6:2004 Advanced technical ceramics. Monolithic ceramics. Mechanical properties at room temperature. Guidance for fractographic investigation
    Superseded by BS EN 843-6:2009
  • BS EN 1452-1:1999 Plastics piping systems for water supply. Unplasticized poly (vinyl chloride) (PVC-U). General
    Superseded by BS EN ISO 1452-1:2009
  • BS EN 1452-2:1999 Plastics piping systems for water supply. Unplasticized poly (vinyl chloride) (PVC-U). Pipes
    Superseded by BS EN ISO 1452-2:2009
  • BS EN 1452-3:1999 Plastics piping systems for water supply. Unplasticized poly (vinyl chloride) (PVC-U). Fittings
    Superseded by BS EN ISO 1452-3:2009
  • BS EN 1452-4:1999 Plastics piping systems for water supply. Unplasticized poly(vinyl chloride) (PVC-U). Valves and ancillary equipment
    Superseded by BS EN ISO 1452-4:2009
  • BS EN 1452-5:1999 Plastics piping systems for water supply. Unplasticized poly (vinyl chloride) (PVC-U). Fitness for purpose of the system
    Superseded by BS EN ISO 1452-5:2009
  • BS EN 1456-1:2001 Plastic piping systems for buried and aboveground drainage and sewerage under pressure. Unplasticized poly(vinyl chloride) (PVC-U). Specifications for piping components and the system
    Superseded by BS EN ISO 1452-1:2009, BS EN ISO 1452-2:2009, BS EN ISO 1452-3:2009, BS EN ISO 1452-4:2009 and BS EN ISO 1452-5:2009
  • DD ENV 1999-1-2:2000 Eurocode 9. Design of aluminium structures. General rules. Structural fire design
    Superseded by BS EN 1999-1-2:2007
  • BS EN ISO 9241-7:1998 Ergonomic requirements for office work with visual display terminals (VDTs). Requirements for display with reflections
    Superseded by BS EN ISO 9241-302:2008, BS EN ISO 9241-303:2008, BS EN ISO 9241-304:2008, BS EN ISO 9241-305:2008 and BS EN ISO 9241-307:2008
  • BS EN ISO 9241-8:1998 Ergonomic requirements for office work with visual display terminals (VDTs). Requirements for displayed colours
    Superseded by BS EN ISO 9241-302:2008, BS EN ISO 9241-303:2008, BS EN ISO 9241-304:2008, BS EN ISO 9241-305:2008 and BS EN ISO 9241-307:2008
  • BS EN 12818:2002 LPG equipment and accessories. Inspection and requalification of LPG tanks up to and including 13 m3 underground
    Superseded by BS EN 12817:2010
  • BS EN 12820:2002 Inspection and requalification of LPG tanks greater than 13 m3 underground
    Superseded by BS EN 12819:2009
  • BS EN ISO 13406-1:1999 Ergonomic requirements for work with visual display based on flat panels. Introduction
    Superseded by BS EN ISO 9241-302:2008, BS EN ISO 9241-303:2008, BS EN ISO 9241-304:2008, BS EN ISO 9241-305:2008 and BS EN ISO 9241-307:2008
  • BS EN ISO 13406-2:2002 Ergonomic requirements for work with visual display based on flat panels. Ergonomic requirements for flat panel displays
    Superseded by BS EN ISO 9241-302:2008, BS EN ISO 9241-303:2008, BS EN ISO 9241-304:2008, BS EN ISO 9241-305:2008 and BS EN ISO 9241-307:2008
  • DD CEN/TS 14774-1:2004 Solid biofuels. Methods for the determination of moisture content. Oven dry method. Total moisture. Reference method
    Superseded by BS EN 14774-1:2009
  • DD CEN/TS 14774-2:2004 Solid biofuels. Methods for the determination of moisture content. Oven dry method. Total moisture. Simplified method
    Superseded by BS EN 14774-2:2009
  • DD CEN/TS 14774-3:2004 Solid biofuels. Methods for the determination of moisture content. Oven dry method. Moisture in general analysis sample
    Superseded by BS EN 14774-3:2009
  • BS EN 29241-3:1993 Ergonomic requirements for office work with visual display terminals (VDTs). Visual display requirements
    Superseded by BS EN ISO 9241-302:2008, BS EN ISO 9241-303:2008, BS EN ISO 9241-304:2008, BS EN ISO 9241-305:2008 and BS EN ISO 9241-307:2008
  • BS EN 50144-2-13:2002 Safety of hand-held electric motor operated tools. Particular requirements for chain saws
    Superseded by BS EN 60745-2-13:2007
  • BS EN 50266-1:2001 Common test methods for cables under fire conditions. Test for vertical flame spread of vertically-mounted bunched wires or cables. Apparatus
    Superseded by BS EN 60332-3-10:2009
  • BS EN 50266-2-1:2001 Common test methods for cables under fire conditions. Test for vertical flame spread of vertically-mounted bunched wires or cables. Procedures. Category A F/R
    Superseded by BS EN 60332-3-21:2009
  • BS EN 50266-2-2:2001 Common test methods for cables under fire conditions. Test for vertical flame spread of vertically-mounted bunched wires or cables. Procedures. Category A
    Superseded by BS EN 60332-3-22:2009
  • BS EN 50266-2-3:2001 Common test methods for cables under fire conditions. Test for vertical flame spread of vertically-mounted bunched wires or cables. Procedures. Category B
    Superseded by BS EN 60332-3-23:2009
  • BS EN 50266-2-4:2001 Common test methods for cables under fire conditions. Test for vertical flame spread of vertically-mounted bunched wires or cables. Procedures. Category C
    Superseded by BS EN 60332-3-24:2009
  • BS EN 50266-2-5:2001 Common test methods for cables under fire conditions. Test for vertical flame spread of vertically-mounted bunched wires or cables. Procedures. Small cables. Category D
    Superseded by BS EN 60332-3-25:2009
  • BS EN 60269-1:1999 Low-voltage fuses. General requirements
    Superseded by BS EN 60269-1:2007+A1:2009
  • BS EN 60269-2:1995 Low-voltage fuses. Supplementary requirements for fuses for use by authorized persons (fuses mainly for industrial application)
    Superseded by BS 88-2:2007 and BS EN 60269-1:2007+A1:2009
  • BS EN 60269-3:1995 Low-voltage fuses. Supplementary requirements for fuses for use by unskilled persons (fuses mainly for household and similar applications)
    Superseded by BS 88-3:2007 and BS EN 60269-1:2007+A1:2009
  • BS EN 60269-4:1996 Low-voltage fuses. Supplementary requirements for fuse-links for the protection of semiconductor devices
    Superseded by BS EN 60269-4:2007
  • BS EN 60269-4-1:2002 Low-voltage fuses. Supplementary requirements for fuse-links for the protection of semiconductor devices. Sections I to III. Examples of types of standardized fuse-links
    Superseded by BS EN 60269-4:2007
  • BS EN 60570:1997 Electrical supply track systems for luminaires
    Superseded by BS EN 60570:2003
  • BS EN 60570-2-1:1995 Electrical supply track systems for luminaires. Mixed supply systems. Classes I and III
    Superseded by BS EN 60570:2003
  • BS EN 60603-7-1:2002 Connectors for frequencies below 3 MHz for use with printed boards. Detail specification for 8-way, shielded free and fixed connectors with common mating features, with assessed quality
    Superseded by BS EN 60512-26-100:2008 and BS EN 60603-7-1:2009
  • BS EN 61000-4-12:1996 Electromagnetic compatibility (EMC). Testing and measurement techniques. Oscillatory waves immunity test. Basic EMC publication
    Superseded by BS EN 61000-4-12:2006 and BS EN 61000-4-18:2007
  • BS EN 61280-2-5:1998 Fibre optic communication subsystem basic test procedures. Test procedures for digital systems. Jitter transfer function measurement
    Superseded by BS EN 61280-2-3:2009
  • BS EN 61290-2-3:1998 Optical fibre amplifiers. Basic specification. Test methods for optical power parameters. Optical power meter
    Superseded by BS EN 61290-1-3:2005
  • BS EN 61346-1:1996 Industrial systems, installations and equipment and industrial products. Structuring principles and reference designations. Basic rules
    Superseded by BS EN 81346-1:2009
  • BS EN 61346-2:2001 Industrial systems, installations and equipment and industrial products. Structuring principles and reference designations. Classification of objects and codes for classes
    Superseded by BS EN 81346-2:2009
  • BS EN 61557-1:1997 Electrical safety in low voltage distribution systems up to 1000 V A.C. and 1500 V D.C. Equipment for testing, measuring or monitoring of protective measures. General requirements
    Superseded by BS EN 61557-1:2007
  • BS EN 61557-2:1997 Electrical safety in low voltage distribution systems up to 1000 V A.C. and 1500 V D.C. Equipment for testing, measuring or monitoring of protective measures. Insulation resistance
    Superseded by BS EN 61557-2:2007
  • BS EN 61557-3:1997 Electrical safety in low voltage distribution systems up to 1000 V A.C. and 1500 V D.C. Equipment for testing, measuring or monitoring of protective measures. Loop impedance
    Superseded by BS EN 61557-3:2007
  • BS EN 61557-4:1997 Electrical safety in low voltage distribution systems up to 1000 V A.C. and 1500 V D.C. Equipment for testing, measuring or monitoring of protective measures. Resistance of earth connection and equipotential bonding
    Superseded by BS EN 61557-4:2007
  • BS EN 61557-5:1997 Electrical safety in low voltage distribution systems up to 1000 V A.C. and 1500 V D.C. Equipment for testing, measuring or monitoring of protective measures. Resistance to earth
    Superseded by BS EN 61557-5:2007
  • BS EN 61557-7:1997 Electrical safety in low voltage distribution systems up to 1000 V A.C. and 1500 V D.C. Equipment for testing, measuring or monitoring of protective measures. Phase sequence
    Superseded by BS EN 61557-7:2007
  • BS EN 61558-2-17:1998 Safety of power transformers, power supply units and similar. Particular requirements for transformers for switch mode power supplies
    Superseded by BS EN 61558-2-16:2009
  • BS EN 62086-1:2005 Electrical apparatus for explosive gas atmospheres. Electrical resistance trace heating. General and testing requirements
    Superseded by BS EN 60079-30-1:2007
  • BS EN 62086-2:2005 Electrical apparatus for explosive gas atmospheres. Electrical resistance trace heating. Application guide for design, installation and maintenance
    Superseded by BS EN 60079-30-2:2007
  • BS ISO 31-0:1992 Quantities and units. General principles
    Superseded by BS ISO 80000-1:2009
  • BS ISO 31-9:1992 Quantities and units. Atomic and nuclear physics
    Superseded by BS ISO 80000-10:2009
  • BS ISO 31-10:1992 Quantities and units. Nuclear reactions and ionizing radiations
    Superseded by BS ISO 80000-10:2009
  • BS ISO 31-11:1992 Quantities and units. Mathematical signs and symbols for use in the physical sciences and technology
    Superseded by BS ISO 80000-2:2009
  • BS ISO 1000:1992 SI units and recommendations for the use of their multiples and of certain other units
    Superseded by BS ISO 80000-1:2009
  • BS ISO 10836:1994 Iron ores. Method of sampling and sample preparation for physical testing
    Superseded by BS ISO 3082:2009
  • BS ISO 13320-1:1999 Particle size analysis. Laser diffraction methods. General principles
    Superseded by BS ISO 13320:2009
  • BS ISO 13628-5:2002 Petroleum and natural gas industries. Design and operation of subsea production systems. Subsea umbilicals
    Superseded by BS EN ISO 13628-5:2009
  • BS ISO/IEC 18028-1:2006 Information technology. Security techniques. IT network security. Network security management
    Superseded by BS ISO/IEC 27033-1:2009
  • BS IEC 60880:2006 Nuclear power plants. Instrumentation and control systems important to safety. Software aspects for computer-based systems performing category A functions
    Superseded by BS EN 60880:2009
  • DD IEC/PAS 62074-1:2007 Fibre optic WDM devices. Generic specification
    Superseded by BS EN 62074-1:2009
  • DD IEC/PAS 62267:2005 Railway applications. Automated urban guided transport (AUGT). Safety requirements
    Superseded by BS EN 62267:2009
  • DD IEC/PAS 62400:2005 Structuring principles for technical products and technical product documentation. Letter codes. Main classes and subclasses of objects according to their purpose and task
    Superseded by BS EN 81346-2:2009
  • BS IEC 62448:2007 Multimedia systems and equipment. Multimedia e-publishing and e-books. Generic format for e-publishing
    Superseded by BS EN 62448:2009
  • PD 1002:1997 A guide to cabling in private telecommunications systems
    This document has been withdrawn as it is no longer relevant
  • PD 6532-5:2000 Reference materials. Guide to the contents of certificates of reference materials. General requirements for the competence of reference material producers
    Superseded by PD ISO Guide 34:2009
  • PD 6576:1995 Memorandum on health and safety standardization in support of 'New Approach' Directives. Application in the field of machinery
    This document has been withdrawn
  • BS QC 300900:1991 Harmonized system of quality assessment for electronic components. Fixed capacitors for use in electronic equipment. Sectional specification: fixed polystyrene film dielectric metal foil D.C. capacitors
    This standard has been withdrawn following the withdrawal without supersession of IEC 60384-7:1991, of which it was the UK implementation
  • BS QC 300901:1992 Harmonized system of quality assessment for electronic components. Fixed capacitors for use in electronic equipment. Blank detail specification. Fixed polystyrene film dielectric metal foil D.C. capacitors. Assessment level E
    This standard has been withdrawn following the withdrawal without supersession of IEC 60384-7-1:1991, of which it was the UK implementation
  • BS AU 201-2:1985 Relays and flashers. Specification for arrangement and functional attribution of relay terminals for road vehicles
    This standard has been withdrawn as the identical International Standard, ISO 7880:1984 was withdrawn as it is no longer required by the industry
  • BS AU 206-1:1986 Diagnostic systems for road vehicles. Glossary
    This standard has been withdrawn as the identical International Standard, ISO 4092:1984 was withdrawn as it is no longer required by the industry
  • BS AU 206-2:1986 Diagnostic systems for road vehicles. Specification for graphical symbols for diagnostic testers
    This standard has been withdrawn as the identical International Standard, ISO 7639:1985 was withdrawn as it is no longer required by the industry
  • BS AU 206-3:1986 Diagnostic systems for road vehicles. Specification for general requirements for testing ignition systems
    This standard has been withdrawn as the identical International Standard, ISO 7342:1982 was withdrawn as it is no longer required by the industry
  • BS AU 234:1989 Methods of test and general requirements for road vehicle starter motors
    This standard has been withdrawn as the identical International Standard, ISO 8856:1988 was withdrawn as it is no longer required by the industry
  • PAS 55-1:2003 Asset management. Specification for the optimised management of physical infrastructure assets
    Superseded by PAS 55-1:2008
  • PAS 55-2:2003 Asset management. Guidelines for the application of PAS 55-1
    Superseded by PAS 55-2:2008

Published in international.