ISO 22554:2015
Ships and marine technology — Propeller shaft revolution indicators — Electric type and electronic type
ISO 22554:2015 specifies the construction, performance requirements, methods of testing, and required test results for electric and electronic propeller shaft revolution indicators (hereinafter referred to as "indicator system") required by Clause 2.5.4, Regulation 19, chapter V, SOLAS 1974 (as amended, 2000).
This International Standard is associated with IMO Resolution A.694 (17) and IEC 60945.
Where a requirement in this International Standard differs from IEC 60945, the requirement in this International Standard takes precedence.
NOTE When this indicator system can be used as the tachometer for the engine of a ship, its usage as the tachometer will be accepted.
| Get this standard | Prices exclude GST | |
|---|---|---|
| PDF ( Single user document) |
$126.00 NZD
|
|
| Networkable PDF |
Price varies
|
Section sec_1
Section sec_2
Section sec_3
Section sec_3.1
Section sec_3.2
Section sec_3.3
Section sec_3.4
Section sec_3.5
Section sec_3.6
Section sec_3.7
Section sec_3.8
Section sec_4
Section sec_4.1
Section sec_4.1.1
Section sec_4.1.2
Section sec_4.1.3
Section sec_4.1.4
Section sec_4.1.5
Table tab_a
Figure fig_1
Section sec_4.2
Section sec_4.2.1
Section sec_4.2.2
Section sec_4.2.2.1
Section sec_4.2.2.2
Section sec_4.2.2.3
Section sec_4.2.3
Section sec_4.2.3.1
Section sec_4.2.3.2
Section sec_4.3
Section sec_4.3.1
Section sec_4.3.2
Section sec_4.3.3
Section sec_4.3.4
Section sec_4.3.5
Section sec_4.3.6
Section sec_4.3.7
Section sec_4.3.8
Section sec_5
Section sec_5.1
Section sec_5.2
Section sec_5.3
Section sec_5.4
Section sec_5.5
Section sec_5.6
Section sec_5.7
Section sec_5.8
Section sec_5.8.1
Section sec_5.8.2
Section sec_5.8.3
Section sec_5.9
Section sec_5.9.1
Section sec_5.9.2
Section sec_5.9.3
Table tab_1
Section sec_5.9.4
Section sec_5.10
Section sec_6
Section sec_6.1
Section sec_6.2
Section sec_6.3
Section sec_6.4
Section sec_6.5
Section sec_6.6
Section sec_6.7
Section sec_6.8
Section sec_6.9
Section sec_6.10
Section sec_6.11
Section sec_7
Section sec_8
Section sec_8.1
Section sec_8.2
Section sec_8.3
Section sec_9
Reference ref_1
Reference ref_2
Reference ref_3
Reference ref_4
Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Construction of indicator system
4.1 Indicator system
4.2 Transmitters
4.3 Indicator
5 Performance requirements
5.1 General
5.2 Balance
5.3 Friction error
5.4 Calibration accuracy
5.5 Damping
5.6 Zero point
5.7 Output electric signal of a signal converter
5.8 Output electric signal accuracy of a signal converter
5.9 Power supply fluctuations
5.10 Insulation resistance and high voltage
6 Methods of testing and required test results
6.1 Test items and sequence
6.2 Construction
6.3 Environmental test
6.4 Balance test
6.5 Friction test
6.6 Calibration accuracy test
6.7 Damping test
6.8 Zero point test
6.9 Signal converter output electric signal test
6.10 Signal converter output electric signal accuracy test
6.11 Power supply fluctuation test
7 Interface
8 Marking
9 Information
Bibliography
Previous versions
Keep me up-to-date
Sign up to receive updates when there are changes to this standard
Related Information
Similar Standards
-
AS/NZS 4869.1:2006
Maritime Survivor Locating Systems (MSLS) - Operating on 121.5 MHz
-
AS/NZS 61097.12:2008
Global maritime distress and safety system (GMDSS) - Survival craft portable two-way VHF radiotelephone apparatus - Operational and performance requirements, methods of testing and required test results
-
AS/NZS 62320.1:2015
Maritime navigation and radiocommunication equipment and systems - Automatic identification system (AIS) - Part 1: AIS Base Stations - Minimum operational and performance requirements, methods of testing and required test results -
AS/NZS 62320.3:2015
Maritime navigation and radiocommunication equipment and systems - Automatic identification system (AIS) - Part 3: Repeater stations - Minimum operational and performance requirements - Methods of test and required test results
Section sec_1
Section sec_2
Section sec_3
Section sec_3.1
Section sec_3.2
Section sec_3.3
Section sec_3.4
Section sec_3.5
Section sec_3.6
Section sec_3.7
Section sec_3.8
Section sec_4
Section sec_4.1
Section sec_4.1.1
Section sec_4.1.2
Section sec_4.1.3
Section sec_4.1.4
Section sec_4.1.5
Table tab_a
Figure fig_1
Section sec_4.2
Section sec_4.2.1
Section sec_4.2.2
Section sec_4.2.2.1
Section sec_4.2.2.2
Section sec_4.2.2.3
Section sec_4.2.3
Section sec_4.2.3.1
Section sec_4.2.3.2
Section sec_4.3
Section sec_4.3.1
Section sec_4.3.2
Section sec_4.3.3
Section sec_4.3.4
Section sec_4.3.5
Section sec_4.3.6
Section sec_4.3.7
Section sec_4.3.8
Section sec_5
Section sec_5.1
Section sec_5.2
Section sec_5.3
Section sec_5.4
Section sec_5.5
Section sec_5.6
Section sec_5.7
Section sec_5.8
Section sec_5.8.1
Section sec_5.8.2
Section sec_5.8.3
Section sec_5.9
Section sec_5.9.1
Section sec_5.9.2
Section sec_5.9.3
Table tab_1
Section sec_5.9.4
Section sec_5.10
Section sec_6
Section sec_6.1
Section sec_6.2
Section sec_6.3
Section sec_6.4
Section sec_6.5
Section sec_6.6
Section sec_6.7
Section sec_6.8
Section sec_6.9
Section sec_6.10
Section sec_6.11
Section sec_7
Section sec_8
Section sec_8.1
Section sec_8.2
Section sec_8.3
Section sec_9
Reference ref_1
Reference ref_2
Reference ref_3
Reference ref_4
Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Construction of indicator system
4.1 Indicator system
4.2 Transmitters
4.3 Indicator
5 Performance requirements
5.1 General
5.2 Balance
5.3 Friction error
5.4 Calibration accuracy
5.5 Damping
5.6 Zero point
5.7 Output electric signal of a signal converter
5.8 Output electric signal accuracy of a signal converter
5.9 Power supply fluctuations
5.10 Insulation resistance and high voltage
6 Methods of testing and required test results
6.1 Test items and sequence
6.2 Construction
6.3 Environmental test
6.4 Balance test
6.5 Friction test
6.6 Calibration accuracy test
6.7 Damping test
6.8 Zero point test
6.9 Signal converter output electric signal test
6.10 Signal converter output electric signal accuracy test
6.11 Power supply fluctuation test
7 Interface
8 Marking
9 Information
Bibliography