ISO 13784-1:2002
Reaction-to-fire tests for sandwich panel building systems — Part 1: Test method for small rooms
ISO 13874-1:2002 specifies a test method for determining the reaction to fire of sandwich panel building systems for small rooms and the resulting flame spread on or within the sandwich panel building construction when it is exposed to heat from a simulated internal fire with flames impinging directly on its internal corner. The test method is not intended for evaluating a product's fire resistance. ISO 13874-1:2002 is applicable to both freestanding and self-supporting, and frame-supported, sandwich panel systems. It is not applicable to sandwich panel products that are glued, nailed, bonded or similarly supported by an underlying wall or ceiling construction.
| Get this standard | Prices exclude GST | |
|---|---|---|
| PDF ( Single user document) |
$118.26 NZD
|
|
| HardCopy |
$152.17 NZD
|
|
| Networkable PDF |
Price varies
|
TitlePage - Reaction-to-fire tests for sandwich panel building systems—
TableofContent - Contents Page
Foreword - Foreword
Introduction - Introduction
Scope - 1 Scope
NormativeReference - 2 Normative references
Clause1 - 4 Principle
Clause1 - 5 Types of structure
Clause1 - 6 Test specimen
Clause1 - 7 Test room design and construction
UntitledSubclause2 - 7.1 The test method consists of a procedure by which sandwich panel assem...
UntitledSubclause2 - 7.2 Construct a room using the components of the sandwich panel systems i...
UntitledSubclause2 - 7.3 Provide a doorway in the centre of one of the
UntitledSubclause2 - 7.4 The room shall be located indoors. Tests shall not be conducted unles...
UntitledSubclause2 - 7.5 The connections between the panels, and between the walls and the cei...
UntitledSubclause2 - 7.6 If the system includes any additional bracing, support members, etc.,...
UntitledSubclause2 - 7.7 The test room shall be positioned below the exhaust hood in accordanc...
Clause1 - 8 Ignition source
UntitledSubclause2 - 8.1 The ignition source shall be a propane gas burner having a square top...
UntitledSubclause2 - 8.2 The burner shall be placed on the floor in a corner opposite the wall...
UntitledSubclause2 - 8.3 The burner shall be supplied with natural-grade propane (
UntitledSubclause2 - 8.4 The burner heat output, based on the net (lower) calorific value of p...
Clause1 - 9 Apparatus
UntitledSubclause2 - 9.1 Thermocouples
UntitledSubclause2 - 9.2 Heat flux meter
UntitledSubclause2 - 9.3 Additional equipment
UntitledSubclause3 - 9.3.1 Data recorder—
UntitledSubclause3 - 9.3.2 Timing device—
UntitledSubclause2 - 9.4 Heat and smoke release measurement system
Clause1 - 10 Heat and smoke release measurement
Subclause2 - 10.1 General
Subclause2 - 10.2 Method1
Subclause2 - 10.3 Method2
Clause1 - 11 Procedure
Subclause2 - 11.1 Initial conditions
UntitledSubclause3 - 11.1.1 The temperature in the test facility at the start of the test shal...
UntitledSubclause3 - 11.1.2 The horizontal wind speed measured at a horizontal distance of
UntitledSubclause3 - 11.1.3 The burner shall be in contact with the corner wall. The surface a...
UntitledSubclause3 - 11.1.4 The test set-up shall be photographed or video-recorded prior to t...
Subclause2 - 11.2 Test
UntitledSubclause3 - 11.2.1 Start all recording and measuring devices and record data for at l...
UntitledSubclause3 - 11.2.2 Adjust the burner to the required output levels within
UntitledSubclause3 - 11.2.3 Make a photographic or videotape record of the test or both of the...
UntitledSubclause3 - 11.2.4 During the test, record the following observations and the time at...
UntitledSubclause3 - 11.2.5 End the test if flashover occurs (i.e. the rate of heat release ex...
UntitledSubclause3 - 11.2.6 Note the extent of damage to the product after testing. Damage sha...
UntitledSubclause3 - 11.2.7 Record any other unusual behaviour.
Clause1 - 12 Precision
Clause1 - 13 Test report
AnnexNormative - Heat and smoke release measurement procedure in accordance with ISO9705— Method1
Clause1 - A.1 Hood and exhaust duct
Clause1 - A.2 Instrumentation in exhaust duct— Minimum requirements
Subclause2 - A.2.1 Volume flow rate
Subclause2 - A.2.2 Gas analysis
Subclause3 - A.2.2.1 Sampling line
Subclause3 - A.2.2.2 Oxygen
Subclause3 - A.2.2.3 Carbon monoxide and carbon dioxide
Subclause2 - A.2.3 Optical density
Subclause3 - A.2.3.1 General
Subclause3 - A.2.3.2 Incandescent lamp photometer
Subclause3 - A.2.3.3 Location
Clause1 - A.3 System performance
Subclause2 - A.3.1 Calibration
Subclause2 - A.3.2 System response
AnnexNormative - Heat and smoke release measurement procedure— Method2
Clause1 - B.1 Enclosure
Clause1 - B.2 Hood and exhaust duct
Clause1 - B.3 Instrumentation in the exhaust duct
AnnexNormative - Calculations
Clause1 - C.1 Volume flow
Clause1 - C.2 Heat release rate, calibration and test process
UntitledSubclause2 - C.2.1 During the calibration process, heat release rate from the ignition...
UntitledSubclause2 - C.2.2 Heat release rate from a test specimen
UntitledSubclause2 - C.2.3 Equations(C.2)
Clause1 - C.3 Combustion gases
Clause1 - C.4 Light obscuration
AnnexInformative - Laser smoke photometer
Keep me up-to-date
Register to receive notifications when updates are made to this standard.
Related Information
Similar Standards
-
AS/NZS 1530.3:1999
Methods for fire tests on building materials, components and structures - Simultaneous determination of ignitability, flame propagation, heat release and smoke release
-
AS/NZS 1720.4:2019
Timber structures - Part 4: Fire resistance of timber elements -
AS/NZS 3013:2005
Electrical installations - Classification of the fire and mechanical performance of wiring system elements
-
BS 476-10:2009
Fire tests on building materials and structures, Guide to the principles, selection, role and application of fire testing and their outputs
TitlePage - Reaction-to-fire tests for sandwich panel building systems—
TableofContent - Contents Page
Foreword - Foreword
Introduction - Introduction
Scope - 1 Scope
NormativeReference - 2 Normative references
Clause1 - 4 Principle
Clause1 - 5 Types of structure
Clause1 - 6 Test specimen
Clause1 - 7 Test room design and construction
UntitledSubclause2 - 7.1 The test method consists of a procedure by which sandwich panel assem...
UntitledSubclause2 - 7.2 Construct a room using the components of the sandwich panel systems i...
UntitledSubclause2 - 7.3 Provide a doorway in the centre of one of the
UntitledSubclause2 - 7.4 The room shall be located indoors. Tests shall not be conducted unles...
UntitledSubclause2 - 7.5 The connections between the panels, and between the walls and the cei...
UntitledSubclause2 - 7.6 If the system includes any additional bracing, support members, etc.,...
UntitledSubclause2 - 7.7 The test room shall be positioned below the exhaust hood in accordanc...
Clause1 - 8 Ignition source
UntitledSubclause2 - 8.1 The ignition source shall be a propane gas burner having a square top...
UntitledSubclause2 - 8.2 The burner shall be placed on the floor in a corner opposite the wall...
UntitledSubclause2 - 8.3 The burner shall be supplied with natural-grade propane (
UntitledSubclause2 - 8.4 The burner heat output, based on the net (lower) calorific value of p...
Clause1 - 9 Apparatus
UntitledSubclause2 - 9.1 Thermocouples
UntitledSubclause2 - 9.2 Heat flux meter
UntitledSubclause2 - 9.3 Additional equipment
UntitledSubclause3 - 9.3.1 Data recorder—
UntitledSubclause3 - 9.3.2 Timing device—
UntitledSubclause2 - 9.4 Heat and smoke release measurement system
Clause1 - 10 Heat and smoke release measurement
Subclause2 - 10.1 General
Subclause2 - 10.2 Method1
Subclause2 - 10.3 Method2
Clause1 - 11 Procedure
Subclause2 - 11.1 Initial conditions
UntitledSubclause3 - 11.1.1 The temperature in the test facility at the start of the test shal...
UntitledSubclause3 - 11.1.2 The horizontal wind speed measured at a horizontal distance of
UntitledSubclause3 - 11.1.3 The burner shall be in contact with the corner wall. The surface a...
UntitledSubclause3 - 11.1.4 The test set-up shall be photographed or video-recorded prior to t...
Subclause2 - 11.2 Test
UntitledSubclause3 - 11.2.1 Start all recording and measuring devices and record data for at l...
UntitledSubclause3 - 11.2.2 Adjust the burner to the required output levels within
UntitledSubclause3 - 11.2.3 Make a photographic or videotape record of the test or both of the...
UntitledSubclause3 - 11.2.4 During the test, record the following observations and the time at...
UntitledSubclause3 - 11.2.5 End the test if flashover occurs (i.e. the rate of heat release ex...
UntitledSubclause3 - 11.2.6 Note the extent of damage to the product after testing. Damage sha...
UntitledSubclause3 - 11.2.7 Record any other unusual behaviour.
Clause1 - 12 Precision
Clause1 - 13 Test report
AnnexNormative - Heat and smoke release measurement procedure in accordance with ISO9705— Method1
Clause1 - A.1 Hood and exhaust duct
Clause1 - A.2 Instrumentation in exhaust duct— Minimum requirements
Subclause2 - A.2.1 Volume flow rate
Subclause2 - A.2.2 Gas analysis
Subclause3 - A.2.2.1 Sampling line
Subclause3 - A.2.2.2 Oxygen
Subclause3 - A.2.2.3 Carbon monoxide and carbon dioxide
Subclause2 - A.2.3 Optical density
Subclause3 - A.2.3.1 General
Subclause3 - A.2.3.2 Incandescent lamp photometer
Subclause3 - A.2.3.3 Location
Clause1 - A.3 System performance
Subclause2 - A.3.1 Calibration
Subclause2 - A.3.2 System response
AnnexNormative - Heat and smoke release measurement procedure— Method2
Clause1 - B.1 Enclosure
Clause1 - B.2 Hood and exhaust duct
Clause1 - B.3 Instrumentation in the exhaust duct
AnnexNormative - Calculations
Clause1 - C.1 Volume flow
Clause1 - C.2 Heat release rate, calibration and test process
UntitledSubclause2 - C.2.1 During the calibration process, heat release rate from the ignition...
UntitledSubclause2 - C.2.2 Heat release rate from a test specimen
UntitledSubclause2 - C.2.3 Equations(C.2)
Clause1 - C.3 Combustion gases
Clause1 - C.4 Light obscuration
AnnexInformative - Laser smoke photometer