AS/NZS IEC 63103:2021
Lighting equipment - Non-active mode power measurement
Standard identically adopts IEC 63103:2020 for Australia, which specifies methods of measurement of electrical power consumption in nonactive mode(s), as applicable for electrical lighting equipment. This includes electrical lighting equipment incorporating non‐illumination components. This document applies to lighting equipment connected to a supply voltage up to 1 500 V DC or up to 1 000 V AC.
| Get this standard | Prices exclude GST | |
|---|---|---|
| PDF ( Single user document) |
$155.70 NZD
|
|
| HardCopy |
$173.00 NZD
|
|
| Networkable PDF |
Price varies
|
|
| Online Library ( Annual subscription) |
Info
Price varies
Online Library subscription information Online library subscriptions provide a cost-effective solution for organisations of any size to access the latest standards, offering 24/7 access to a personalised catalogue. The service ensures subscribers have have the most up-to-date version of selected standards, incluing automatic updates for any amendments or versions. Pricing is dependent on the chosen standards and the number of concurrent users, with discounts applied from the standards PDF price. For customised subscriptions or further inquiries, contact the Online Library team. |
AS/NZS IEC 63103:2021 Lighting equipment -- Non-active mode power measurement
CONTENTS
FOREWORD
INTRODUCTION
1 Scope
2 Normative references
3 Terms and definitions
4 General test conditions
4.1 General
4.2 Laboratory and environmental conditions
4.3 Supply voltage
4.3.1 Supply voltage and frequency
4.3.2 Supply voltage waveform
4.4 Power measurement accuracy and uncertainty
4.5 Network aspects
4.5.1 General
4.5.2 Wired networks
4.5.3 Wireless networks: conducted connection for testing
4.5.4 Wireless networks: radiated connection for testing
5 Measurements
5.1 General
5.2 Equipment under test (EUT)
5.2.1 General
5.2.2 Illumination-only lighting equipment
5.2.3 Multi-function lighting equipment
5.3 Preparation of EUT
5.3.1 General
5.3.2 Measurement of input power
5.3.3 EUT with no network provision
5.3.4 EUT with network provision (wired or wireless)
5.4 Measuring procedure
5.4.1 General
5.4.2 Direct meter reading method
5.4.3 Average reading method
5.4.4 Sampling method
Annex€A (informative)Guidance for product standards
Annex€B (normative)Measurement setup schemesfor illumination-only lighting equipment
Annex€C (normative)Measurement setup schemes for multi-function lighting equipment
Annex€D (informative)Application examples
Bibliography
Figures
Figure 1 – Test setup for non-active mode power consumption measurementof conducted connected EUT
Figure 2 – Test setup for non-active mode power consumption measurementof connected EUT with integral antennas (RF path symbolically shown)
Figure 3 – Calibration setup for non-active mode power measurementof connected EUT with integral antennas
Figure 4 – Components present within illumination-only EUT
Figure 5 – Component representing an additional function (AF) of multi-function EUT
Figure 6 – Configuration of multi-function lighting equipment:example including one additional function
Figure B.1 – Key to symbols used in figures of Annex€B
Figure B.2 – Measurement setup for determining the input powersupplied to the power supply
Figure B.3 – Measurement setup (with optional network provision)for determining the input power supplied to the control unit
Figure B.4 – Measurement setup (with optional network provision) for determining the input power supplied to the combined power supply and control unit
Figure B.5 – Measurement setup for determining the input power suppliedto the combined light source and power supply
Figure B.6 – Measurement setup (with optional network provision) for determining the input power supplied to the combined light source and control unit
Figure B.7 – Measurement setup (with optional network provision) for determiningthe input power supplied to illumination-only lighting equipment
Figure C.1 – Key to symbols used in figures of Annex€C
Figure C.2 – Measurement setup (with optional network provision) for determining the input power to multi-function lighting equipment
Figure D.1 – General measurement setup scheme for controlgear examples
Figure D.2 – Networked standby mode measurement setup for the "basic" controlgear
Figure D.3 – Networked standby mode measurement setup for controlgearwith an integrated auxiliary/bus power supply function
Tables
Table 1 – Configurations and examples of illumination-only equipmentand reference to the measurement setup
Table 2 – Template for reporting non-active mode power
Table 3 – Example of using the template of Table 2for reporting measured standby power for an illumination-only luminairewith integrated presence sensor
Table 4 – Example of using the template of Table 2for reporting measured standby power for a (multi-function) luminairewith an integrated presence sensor and an integrated camera
Keep me up-to-date
Register to receive notifications when updates are made to this standard.
Related Information
Similar Standards
-
AS/NZS 3113:2005
Approval and test specification - Ceiling roses
-
AS/NZS 4782.2:2004
Double-capped fluorescent lamps - Performance specifications - Minimum Energy Performance Standard (MEPS)
-
AS/NZS 4782.2:2004 A1
Double-capped fluorescent lamps - Performance specifications - Minimum Energy Performance Standard (MEPS): Amendment 1
-
AS/NZS 4782.2:2004 A2
Double-capped fluorescent lamps - Performance specifications - Minimum Energy Performance Standard (MEPS): Amendment 2
AS/NZS IEC 63103:2021 Lighting equipment -- Non-active mode power measurement
CONTENTS
FOREWORD
INTRODUCTION
1 Scope
2 Normative references
3 Terms and definitions
4 General test conditions
4.1 General
4.2 Laboratory and environmental conditions
4.3 Supply voltage
4.3.1 Supply voltage and frequency
4.3.2 Supply voltage waveform
4.4 Power measurement accuracy and uncertainty
4.5 Network aspects
4.5.1 General
4.5.2 Wired networks
4.5.3 Wireless networks: conducted connection for testing
4.5.4 Wireless networks: radiated connection for testing
5 Measurements
5.1 General
5.2 Equipment under test (EUT)
5.2.1 General
5.2.2 Illumination-only lighting equipment
5.2.3 Multi-function lighting equipment
5.3 Preparation of EUT
5.3.1 General
5.3.2 Measurement of input power
5.3.3 EUT with no network provision
5.3.4 EUT with network provision (wired or wireless)
5.4 Measuring procedure
5.4.1 General
5.4.2 Direct meter reading method
5.4.3 Average reading method
5.4.4 Sampling method
Annex€A (informative)Guidance for product standards
Annex€B (normative)Measurement setup schemesfor illumination-only lighting equipment
Annex€C (normative)Measurement setup schemes for multi-function lighting equipment
Annex€D (informative)Application examples
Bibliography
Figures
Figure 1 – Test setup for non-active mode power consumption measurementof conducted connected EUT
Figure 2 – Test setup for non-active mode power consumption measurementof connected EUT with integral antennas (RF path symbolically shown)
Figure 3 – Calibration setup for non-active mode power measurementof connected EUT with integral antennas
Figure 4 – Components present within illumination-only EUT
Figure 5 – Component representing an additional function (AF) of multi-function EUT
Figure 6 – Configuration of multi-function lighting equipment:example including one additional function
Figure B.1 – Key to symbols used in figures of Annex€B
Figure B.2 – Measurement setup for determining the input powersupplied to the power supply
Figure B.3 – Measurement setup (with optional network provision)for determining the input power supplied to the control unit
Figure B.4 – Measurement setup (with optional network provision) for determining the input power supplied to the combined power supply and control unit
Figure B.5 – Measurement setup for determining the input power suppliedto the combined light source and power supply
Figure B.6 – Measurement setup (with optional network provision) for determining the input power supplied to the combined light source and control unit
Figure B.7 – Measurement setup (with optional network provision) for determiningthe input power supplied to illumination-only lighting equipment
Figure C.1 – Key to symbols used in figures of Annex€C
Figure C.2 – Measurement setup (with optional network provision) for determining the input power to multi-function lighting equipment
Figure D.1 – General measurement setup scheme for controlgear examples
Figure D.2 – Networked standby mode measurement setup for the "basic" controlgear
Figure D.3 – Networked standby mode measurement setup for controlgearwith an integrated auxiliary/bus power supply function
Tables
Table 1 – Configurations and examples of illumination-only equipmentand reference to the measurement setup
Table 2 – Template for reporting non-active mode power
Table 3 – Example of using the template of Table 2for reporting measured standby power for an illumination-only luminairewith integrated presence sensor
Table 4 – Example of using the template of Table 2for reporting measured standby power for a (multi-function) luminairewith an integrated presence sensor and an integrated camera
AS/NZS IEC 63103:2021
Online Library subscription information
Online library subscriptions provide a cost-effective solution for organisations of any size to access the latest standards, offering 24/7 access to a personalised catalogue. The service ensures subscribers have have the most up-to-date version of selected standards, incluing automatic updates for any amendments or versions. Pricing is dependent on the chosen standards and the number of concurrent users, with discounts applied from the standards PDF price. For customised subscriptions or further inquiries, contact the Online Library team.