AS/NZS 61000.3.2:2007
Electromagnetic compatibility (EMC) - Limits - Limits for harmonic current emissions (equipment input current less than or equal to 16 A per phase)
To provide manufacturers and suppliers of electricity and users of electrical equipment intended for connection to an electrical network with limits for voltage disturbances and harmonics produced by that equipment and the methods for ascertaining compliance to them in order to maintain electromagnetic compatibility within the electrical network. Adopted with modifications from IEC 61000-3-2, Ed.3.0(2005).
| Get this standard | Prices exclude GST | |
|---|---|---|
| PDF ( Single user document) |
$132.30 NZD
|
|
| HardCopy |
$147.00 NZD
|
|
| Networkable PDF |
Price varies
|
|
| Online Library ( Annual subscription) |
Info
Price varies
Online Library subscription information Online library subscriptions provide a cost-effective solution for organisations of any size to access the latest standards, offering 24/7 access to a personalised catalogue. The service ensures subscribers have have the most up-to-date version of selected standards, incluing automatic updates for any amendments or versions. Pricing is dependent on the chosen standards and the number of concurrent users, with discounts applied from the standards PDF price. For customised subscriptions or further inquiries, contact the Online Library team. |
Committee representation
Keeping Standards up-to-date
History
COPYRIGHT
PREFACE
CONTENTS
INTRODUCTION
SECTION
1 Scope
2 Normative references
3 Definitions
4 General
5 Classification of equipment
6 General requirements
7 Harmonic current limits
Annex
A Measurement circuit and supply source
B Requirements for measurement equipment
C Type test conditions
Table
1 – Limits mainly for Class A equipment
2 – Limits for Class C equipment
3 – Limits mainly for Class D equipment
A.1 – Measurement circuit for single-phase equipment
A.2 – Measurement circuit for three-phase equipment
C.1 – Conventional load for arc welding equipment tests
Figure
1 – Flowchart for determining conformity
A.1 – Measurement circuit for single-phase equipment
A.2 – Measurement circuit for three-phase equipment
AMENDMENT CONTROL SHEET
Amendments
Previous versions
Keep me up-to-date
Register to receive notifications when updates are made to this standard.
Related Information
Electricity (Safety) Regulations 2010
Ministry: WorkSafe New Zealand: Energy Safety
Section: Schedule 2
Citation context:Refers to 61000.3.2:2007(AS/NZS)A1. AS/NZS 61000.3.2 (means) AS/NZS 61000.3.2:2007: Electromagnetic compatibility (EMC) - Limits - Limits for harmonic current emissions (equipment input current less than or equal to 16 amperes per phase): including Amendments 1 and 2 (sic)
Electricity (Safety) Regulations 2010
Ministry: WorkSafe New Zealand: Energy Safety
Section: Schedule 2
Citation context:AS/NZS 61000.3.2 (means) AS/NZS 61000.3.2:2007: Electromagnetic compatibility (EMC) - Limits - Limits for harmonic current emissions (equipment input current less than or equal to 16 amperes per phase): including Amendments 1 and 2 (sic)
Similar Standards
-
AS/NZS 4365:2011
Radiocommunications equipment used in the UHF citizen band radio service
-
AS/NZS 4417.1:2012
Regulatory compliance mark for electrical and electronic equipment - Part 1: Use of the mark -
AS/NZS 4417.1:2012AA
Regulatory compliance mark for electrical and electronic equipment - Part 1: Use of the mark: Amendment A -
AS/NZS 61000.1.1:2000
Electromagnetic compatibility (EMC) - General - Application and interpretation of fundamental definitions and terms
Committee representation
Keeping Standards up-to-date
History
COPYRIGHT
PREFACE
CONTENTS
INTRODUCTION
SECTION
1 Scope
2 Normative references
3 Definitions
4 General
5 Classification of equipment
6 General requirements
7 Harmonic current limits
Annex
A Measurement circuit and supply source
B Requirements for measurement equipment
C Type test conditions
Table
1 – Limits mainly for Class A equipment
2 – Limits for Class C equipment
3 – Limits mainly for Class D equipment
A.1 – Measurement circuit for single-phase equipment
A.2 – Measurement circuit for three-phase equipment
C.1 – Conventional load for arc welding equipment tests
Figure
1 – Flowchart for determining conformity
A.1 – Measurement circuit for single-phase equipment
A.2 – Measurement circuit for three-phase equipment
AMENDMENT CONTROL SHEET
Amendments
Previous versions
AS/NZS 61000.3.2:2007
Online Library subscription information
Online library subscriptions provide a cost-effective solution for organisations of any size to access the latest standards, offering 24/7 access to a personalised catalogue. The service ensures subscribers have have the most up-to-date version of selected standards, incluing automatic updates for any amendments or versions. Pricing is dependent on the chosen standards and the number of concurrent users, with discounts applied from the standards PDF price. For customised subscriptions or further inquiries, contact the Online Library team.